1. Manuals
  2. Brands
  3. Nice Manuals
  4. Automatic Barriers
  5. X-Bar
  6. Instructions and warnings for installation and use

Nice X-bar Instructions And Warnings For Installation And Use

Hide thumbs Also See for X-bar:
Table of Contents

Advertisement

Quick Links

Download this manual
X-BAR
Automatic barrier
EN - Instructions and warnings for installation and use
IT - Istruzioni ed avvertenze per l'installazione e l'uso
FR - Instructions et avertissements pour l'installation et l'utilisation
ES - Instrucciones y advertencias para la instalación y el uso
DE - Installierungs-und Gebrauchsanleitungen und Hinweise
PL - Instrukcje i ostrzeżenia do instalacji i użytkowania
NL - Aanwijzingen en aanbevelingen voor installatie en gebruik
RU - Инструкции и важная информация для технических специалистов

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the X-bar and is the answer not in the manual?

Questions and answers

Related Manuals for Nice X-bar

Summary of Contents for Nice X-bar

  • Page 1 X-BAR Automatic barrier EN - Instructions and warnings for installation and use IT - Istruzioni ed avvertenze per l’installazione e l’uso FR - Instructions et avertissements pour l’installation et l’utilisation ES - Instrucciones y advertencias para la instalación y el uso DE - Installierungs-und Gebrauchsanleitungen und Hinweise PL - Instrukcje i ostrzeżenia do instalacji i użytkowania...
  • Page 3 3000 mm 179,5 mm 300 mm...
  • Page 5 90°...
  • Page 10 0 ° VIII...
  • Page 11 MOTB OPEN CLOSE FLASH BLUEBUS STOP P.P. OPEN CLOSE...

  • Page 15: Table Of Contents

    Incorrect installation could cause serious physi- Contents cal injury . We recommend that you read this entire manual with care before starting any work . If in doubt, do not install the product and contact the Nice technical assistance department . • CAUTION! – Important instructions: keep this manual in a safe place PICTURES .

  • Page 16: Installation Criteria And Special Warnings Related To Essential

    • Mechanical strength and stability of the product: combination with the articles listed in the product catalogue of Nice S .p .a . The product is designed and constructed to ensure that, during normal use, all These requirements may not be guaranteed if the product is used in con- forces applied, impact and normal wear will not damage or impair mechanical figurations or with other products that have not been foreseen; the use of...

  • Page 17: Chapter 2 - Product Description And Intended Use

    10 % the solar power system “Solemyo” (see paragraph 4 .9 .3) . V3 and V4 speed X-Bar runs on electric energy and in the event of a power failure the pole can Speed V5 20 % be released and moved manually . Alternatively the buffer battery model PS124 can be used (optional accessory - see paragraph 4 .9 .2), which guarantees a...

  • Page 18: Barrier Fixture

    TABLE 3 - Technical specifications of electrical cables (Fig. 1) Connection Cable type Maximum admissible length A: Mains POWER SUPPLY cable cable 3 x 1,5 mm 30 m (note 1) B: Cable for BlueBus devices cable 2 x 0,5 mm 30 m C: POLE LIGHTS D: KEY-OPERATED SELECTOR SWITCH cable 30 m (note 2) cables 4 x 0,25 mm E: Built-in FLASHING LIGHT OPTIONAL FLASHING LIGHT: cable 2 x 0,5 mm 30 m FLASHING LIGHT with aerial cable RG58 shielded cable type 20 m (less than 5 m recommended) IMPORTANT – To make the connection, programming of the FLASH output must be modified (see paragraph 6.2 - Table 7) Note 1 – If the power cable is longer than 30 m, a cable with a larger cross-section is required (3 x 2.5 mm...

  • Page 19: Chapter 4 - Electrical Connections

    IMPORTANT! – NEVER CONNECT DEVICES OTHER THAN THOSE SPE- 01. Loosen the screws of the cover (Fig. 29); CIFIED. 02. Route the electric cables inside X-Bar, starting from the base towards the control unit and routing them to the left; 4.2 - Initial start-up and electrical connections 03. Connect the wires of the electric power cable to the 3-contact terminal with fuse and secure the cable with the collar (Fig.

  • Page 20: Pole Movement Check

    4.9.2 - Buffer battery mod. PS124 (accessory) To insert the radio receiver, disconnect the control unit from the power mains In the event of a mains power failure, X-Bar can also be powered by a buffer and insert the receiver as shown in fig. 34 .

  • Page 21: Commissioning

    Compile the form “Maintenance schedule” containing all maintenance instructions for all devices in the automation and forward it to the owner . In the case of X-Bar, this form is present at the end of this manual, in the removable section .

  • Page 22: Level Two Programming (Adjustable Parameters)

    “Bluebus” output (connected devices) and all the LEDs apart from the Bluebus LED which will flash more slowly. When the control unit receives a command normal operation is restored. When using X-Bar with the Solemyo system, a longer Stand By mode must be set . This operation is performed using the Oview programmer .

Table of Contents