Intel core u-series processor whiskey lake ultra-slim fanless embedded system, 4 gige lan with 2 poe+, 4 usb, 4 com, 9v to 50v dc-in, -40 degrees c to 75 degrees c
Intel core i7/i5/i3 soc whiskey lake ultra-compact fanless embedded system, 2 gige lan, 4 10g usb 3.1 gen 2, 2 com, 9v to 48v, ignition control, -40 degrees c to 85 degrees c (109 pages)
Page 3
This manual is released by Vecow Co., Ltd. for reference purpose only. All product offerings and specifications are subject to change without prior notice. Vecow Co., Ltd. is under no legal commitment to the details of this document. Vecow shall not be liable for direct, indirect, special, incidental, or consequential damages arising out of the use of this document, the products, or any third party infringements, which may result from such use.
Core™ U-series processor with support for wide range temperature from -40°C to 75°C and wide range 9V to 50V power input. Vecow ABP-3000 Series is designed for edge computing and harsh industrial applications including Machine Vision, In-vehicle Computing, Industrial Automation, Intelligent Control, AMR/AGV, or any AIoT/ Industry 4.0 applications.
GETTING TO KNOW YOUR ABP-3000 2.1 Packing List Item Description ABP-3000 Ultra-Compact Embedded System ABP-3000 series accessory box, which contains Item Description Outlook Usage PHILLPIS Mini PCIe 53-2426906-30B M2.5x6L, Ni slot PHILLPIS 53-2426206-80B M3x6L, Ni+Ny Terminal block Switch 51-2211R03-S1A 3-pin (3.5mm)
S3, S5 Suspend to RAM, System off with standby power To power on ABP-3000, press the power button which will light the blue LED. To power off ABP-3000, you can either command shutdown by OS operation or simply press the power button.
Page 16
There are 4 USB 3.1 connections available supporting up to 10GB per second data rate in the front side of ABP-3000 series. It also compliant with the requirements of Super Speed (SS), high speed (HS), full speed (FS) and low speed (LS).
Page 17
PoE ON 2.2.9 10/100/1000 Mbps Ethernet Port There are two 8-pin RJ-45 jacks supporting 10/100/1000 Mbps Ethernet connections ® on the front side of ABP-3000. LAN 1 and LAN 2 are powered by Intel I350 Ethernet engine. ® • Intel I350 Gigabit Ethernet Controller supports 1Gbps data ratet •...
2.5 Main Jumper Settings 2.5.1 Front View of ABP-3000 Main Board with Jumper Location The figure below is the top view of the ABP-3000 main board. It shows the location of the jumpers. JP10 You may configure your card to match the needs of your application by setting jumpers.
The built-in MCU monitors the ignition signal and turns on/off the system according to pre-defined on/off delay period. 2.6.1 Adjust Ignition Control Modes ABP-3000 series provides 16 modes of different power on/off delay periods adjustable via SW3 switch. The default rotary switch is set to 0 in ATX/AT power mode.
Page 39
Note : 1. DC power source and IGN share the same ground. 2. ABP-3000 supports 9V to 50V wide range DC power input in ATX/AT mode. In Ignition mode, the input voltage is fixed to 12V/24V for car battery scenario.
APPENDIX A : Isolated DIO Guide A.1 Function Description The ABP-3000 offers a 16-bit DIO (Isolated/Non-Isolated) 20-pin terminal block connector, a watchdog timer, and a 2-port POE. Isolated DIO pins are fixed by Hardware design that cannot change in/out direction in runtime process.
APPENDIX B : Software Functions B.1 Driver API Guide In Header folder, Vecow.h and VecowLinux.h contain usabled API for Windows/ Linux. BOOL initial_SIO(BYTE Isolate_Type, BYTE DIO_NPN) Initial machine for IO and watch dogtimer. Isolate_Type : DIO type. 1 : Isolated DIO;...
Page 84
C.2 OS Installation ABP-3000 is featured with two NVMe PCIe M.2 (2280) SSD storage. We take two 1TB NVMe PCIe M.2 SSDs for Windows 10 OS installation as an example. C.3 To Install All Device Drivers of the System The instructions are as follows : 1.
Page 85
C.6 To Create RAID Volume on"Rapid Storage Technology" Software ABP-3000 is featured with two NVMe PCIe M.2 SSDs for RAID volume, so there are two options to choose on this page. Let's take RAID 1 as an example, select "RAID 1".