Renesas M30290T-EPB User Manual
  1. Manuals
  2. Brands
  3. Renesas Manuals
  4. Computer Hardware
  5. M30290T-EPB
  6. User manual
Renesas M30290T-EPB User Manual

Renesas M30290T-EPB User Manual

Emulation probe for m16c/26a, 28, 29 group mcus
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
M30290T-EPB
Emulation Probe for M16C/26A, 28, 29 Group MCUs
User's Manual
Rev.1.00
August 16, 2004
REJ10J0388-0100Z

Advertisement

Table of Contents
loading

Related Manuals for Renesas M30290T-EPB

Summary of Contents for Renesas M30290T-EPB

  • Page 1 M30290T-EPB Emulation Probe for M16C/26A, 28, 29 Group MCUs User’s Manual Rev.1.00 August 16, 2004 REJ10J0388-0100Z...
  • Page 2 Notes regarding these materials These materials are intended as a reference to assist our customers in the selection of the Renesas Technology product best suited to the customer's application; they do not convey any license under any intellectual property rights, or any other rights, belonging to Renesas Technology Corporation, Renesas Solutions Corporation or a third party.
  • Page 3 Preface The M30290T-EPB is an emulation probe for the M16C/26A, 28, 29 Group MCUs. The M30290T-EPB is used by connecting to the PC7501 emulator main unit. This user's manual mainly describes specifications of the M30290T-EPB emulation probe and how to setup it. For details on the following products, which are used with the M30290T-EPB, refer to each product's user's manual.

  • Page 4: Table Of Contents

    M30290T-EPB User’s Manual Contents Chapter 1. Precautions for Safety ........................7 1.1 Safety Symbols and Meanings....................8 WARNING ............................9 Warning for Installation......................9 Warning for Use Environment ....................9 CAUTION............................10 Caution to Be Taken for Modifying This Product ..............10 Cautions to Be Taken for Turning On the Power ..............
  • Page 5 Contents Chapter 3. Setup.............................. 23 3.1 Selecting Clock Supply......................24 3.1.1 Clocks..........................24 3.1.2 Using an Internal Oscillator Circuit Board ..............24 3.1.3 Using the Oscillator Circuit on the User System ............27 3.1.4 Using the Internal Generator Circuit................28 3.2 A-D Conversion Bypass Capacitors ..................
  • Page 6 PC7501 system This means an emulator system built around the PC7501 emulator. The PC7501 emulator system is configured with an emulator main unit PC7501, emulation probe M30290T-EPB, emulator debugger M3T-PD30F and host machine. Emulator main unit PC7501 This means an emulator for the M16C Family MCUs. You can configure your emulator system by changing emulation probes according to your target MCU.

  • Page 7: Chapter 1. Precautions For Safety

    Chapter 1. Precautions for Safety Chapter 1. Precautions for Safety This chapter describes precautions for using this product safely and properly. For precautions for the emulator main unit and the emulator debugger, refer to each user's manual included with your product.

  • Page 8: Safety Symbols And Meanings

    M30290T-EPB User’s Manual 1.1 Safety Symbols and Meanings In both the user's manual and on the product itself, several icons are used to insure proper handling of this product and also to prevent injuries to you or other persons, or damage to your properties.

  • Page 9: Warning

    Chapter 1. Precautions for Safety WARNING Warning for Installation: Do not set this product in water or areas of high humidity. Make sure that the main unit does not get wet. Spilling water or some other liquid into the main unit can cause an unrepairable damage. Warning for Use Environment: This equipment is to be used in an environment with a maximum ambient temperature of 35°C.

  • Page 10: Caution

    M30290T-EPB User’s Manual CAUTION Caution to Be Taken for Modifying This Products: Do not modify this product. Modifying or disassembling this product will void your warranty. Cautions to Be Taken for Turning On the Power: Turn on the power of the emulator and user system as simultaneously as possible. And also, turn off the power of the emulator and user system as simultaneously as possible.

  • Page 11: Important

    Chapter 1. Precautions for Safety IMPORTANT Notes on Downloading Firmware: Before using this product for the first time, it is necessary to download the dedicated firmware. Please note that, to do this, it is necessary to start up the emulator main unit in maintenance mode. For downloading firmware, see "4.2 Downloading Firmware"...

  • Page 12: Notes On Maskable Interrupts

    M30290T-EPB User’s Manual IMPORTANT Notes on Maskable Interrupts: Even if a user program is not being executed (including when run-time debugging is being performed), the evaluation MCU keeps running so as to control the emulation probe. Therefore, timers and other components do not stop running.

  • Page 13: Note On Accessing Addresses 00000H And 00001H

    Chapter 1. Precautions for Safety IMPORTANT Note on Accessing Addresses 00000h and 00001h: With the M16C/Tiny Series MCUs, when a maskable interrupt is generated, the interrupt data (interrupt number and interrupt request level) stored in addresses 00000h and 00001h are read out. Also, the interrupt request bit is cleared when address 00000h or 00001h is read out.

  • Page 14: Notes On Address-Match Interrupts

    M30290T-EPB User’s Manual IMPORTANT Notes on Address-Match Interrupts: When you use the address-match interrupt function in a user program, uncheck "Enable the Address Match Interrupt Break Function" in the MCU tab of the Init dialog box of the emulator debugger. Thus, normal software breaks are used for the internal RAM and ROM areas of an MCU.

  • Page 15: Note On Dma Transfer

    Chapter 1. Precautions for Safety IMPORTANT Note on DMA Transfer: With this product, the program is stopped with a loop program to a specific address. Therefore, if a DMA request is generated while the program is stopped, DMA transfer is executed. However, make note that DMA transfer while the program is stopped may not be performed correctly.

  • Page 16: Notes On Debugging In Cpu Rewrite Mode

    M30290T-EPB User’s Manual IMPORTANT Notes on Debugging in CPU Rewrite Mode: When you debug M16C/26A, 28, 29 Group MCUs in CPU rewrite mode, do not change the block 0 area (FF000h--FFFFFh) of the flash ROM. Otherwise, the emulator will be uncontrollable.

  • Page 17: Chapter 2. Preparation

    Chapter 2. Preparation Chapter 2. Preparation This chapter describes the package components, the system configuration and the preparation for using this product for the first time. 2.1 Package Components ..........................18 2.2 Other Tool Products Required for Development ..................18 2.3 Name of Each Part ...........................

  • Page 18: Package Components

    M30290T-EPB user's manual (Japanese) * Please keep the M30290T-EPB's packing box and cushion material in your place for reuse at a later time when sending your product for repair or other purposes. Always use these packing boxes and cushion material when transporting this product.

  • Page 19: Name Of Each Part

    M30290T-80FPD etc. Figure 2.1 System configuration (1) Emulation probe M30290T-EPB This emulation probe consists of the interface board PCA7501EPBA for the M16C/26A, 28, 29 Groups and MCU board M30290T-EPBM for M16C/26A, 28, 29 Group MCUs. The M30290T-EPBM with an evaluation MCU is separately available for replacement.

  • Page 20: Names And Functions Of The Pc7501 Upper Panel Leds

    M30290T-EPB User’s Manual 2.3.2 Names and Functions of the PC7501 Upper Panel LEDs Figure 2.2 shows the names of the LEDs on the upper panel of the PC7501. System status Target status Figure 2.2 Names of the LEDs on the upper panel of the PC7501 (1) System Status LEDs The system status LEDs indicate the emulator PC7501's power supply, firmware operating status, etc.
  • Page 21 Chapter 2. Preparation (2) Target Status LEDs The target status LEDs indicate operating status of the target MCU and power supply of the user system. Table 2.4 lists the definition of each target status LED. Table 2.4 Definition of the target status LEDs Name Status Meaning...

  • Page 22: When Using The Emulator For The First Time

    M30290T-EPB User’s Manual 2.4 When Using the Emulator for the First Time 2.4.1 Downloading Firmware If you have purchased this emulation probe newly, you need to download the firmware. The download procedure is given in Figure 2.3. Before downloading the firmware, check that emulator debugger M3T-PD30F is installed to your host machine and the PC7501 is connected to the host machine.

  • Page 23: Chapter 3. Setup

    Chapter 3. Setup Chapter 3. Setup This chapter describes switch settings required for using this product and how to connect this product to the PC7501 and the user system. 3.1 Selecting Clock Supply..........................24 3.1.1 Clocks.............................. 24 3.1.2 Using an Internal Oscillator Circuit Board ..................24 3.1.3 Using the Oscillator Circuit on the User System ................

  • Page 24: Selecting Clock Supply

    M30290T-EPB User’s Manual 3.1 Selecting Clock Supply 3.1.1 Clocks You can choose a clock supplied to the evaluation MCU by the Emulator tab in the Init dialog box of the emulator debugger. Table 3.1 shows the clocks and their initial settings.
  • Page 25 Chapter 3. Setup 2. Replace the oscillator circuit board (see Figure 3.2). The oscillator circuit board of the PC7501 is in the lower right corner of the board. Unscrew the screw securing the oscillator circuit board. Lift off the oscillator circuit board. Attach another oscillator circuit board to the connector.
  • Page 26 M30290T-EPB User’s Manual (3) Using the Internal Oscillator Circuit Bare Board To use the emulation probe at a frequency you like, build a desired oscillator circuit on the included OSC-2 oscillator circuit bare board. Figure 3.3 shows an external view of the OSC-2 oscillator circuit bare board and where the connector pins are located.

  • Page 27: Using The Oscillator Circuit On The User System

    Chapter 3. Setup 3.1.3 Using the Oscillator Circuit on the User System To operate this product with an external clock, construct the oscillator circuit as shown in Figure 3.5 in the user system and input the oscillator output at 50% duty (within the operating range of the evaluation MCU) into pin X .

  • Page 28: Using The Internal Generator Circuit

    M30290T-EPB User’s Manual 3.1.4 Using the Internal Generator Circuit The dedicated circuit in the PC7501 can generate any arbitrary frequency specified by the emulator debugger, and it can be supplied as a main clock. It does not depend on either the oscillator circuit board in the PC7501 or the oscillator circuit on the user system.

  • Page 29: A-D Conversion Bypass Capacitors

    Chapter 3. Setup 3.2 A-D Conversion Bypass Capacitors There is a foot pattern on the M30290T-EPBM board for mounting bypass capacitors for the A-D conversion circuit near the MCU. Mount suitable bypass capacitors as occasion demands. Figure 3.7 shows where they are installed and the configuration of this product.

  • Page 30: Connecting The Pc7501

    M30290T-EPB User’s Manual 3.3 Connecting the PC7501 Figure 3.8 shows how to connect the PC7501 and the emulation probe. M3T-FLX160-EPB Emulation probe Figure 3.8 Connecting the PC7501 and the emulation probe CAUTION Notes on Connecting the PC7501: When connecting the emulation probe, be sure to hold the both sides of the emulation probe horizontally and insert it directly.

  • Page 31: Connecting The User System

    Chapter 3. Setup 3.4 Connecting the User System Figure 3.9 shows how to connect this product according to your user system. Emulation probe M30290T-EPB 42-pin 48-pin 64-pin 80-pin 0.8-mm-pitch 0.5-mm-pitch 0.5-mm-pitch 0.5-mm-pitch M30263T-42SSB M30291T-64FPD M30290T-80FPD SSOP LQFP M30260T-48FPD LQFP LQFP...

  • Page 32: Connecting To A 42-Pin 0.8-Mm-Pitch Foot Pattern

    (2) Attach the M3T-SSOP42B-450 included with the M30263T-42SSB and the socket frame to the socket main unit. (3) Attach the J1 and J2 of the M30290T-PTCB to the J3 and J4 of the M30290T-EPB. (4) Attach the M30263T-42SSB to the M3T-SSOP42B-450.

  • Page 33: Connecting To A 48-Pin 0.5-Mm-Pitch Foot Pattern

    (2) Attach the YQPACK048SD included with the M30260T-48FPD to the NQPACK048SD and secure it with the YQ-GUIDE's. (3) Attach the J1 and J2 of the M30290T-PTCB to the J3 and J4 of the M30290T-EPB. (4) Attach the M30260T-48FPD to the YQPACK048SD.

  • Page 34: Connecting To A 64-Pin 0.5-Mm-Pitch Foot Pattern

    (2) Attach the YQPACK064SD included with the M30291T-64FPD to the NQPACK064SD-ND and secure it with the YQ-GUIDE's. (3) Attach the J1 and J2 of the M30290T-PTCB to the J3 and J4 of the M30290T-EPB. (4) Attach the M30291T-64FPD to the YQPACK064SD.

  • Page 35: Connecting To An 80-Pin 0.5-Mm-Pitch Foot Pattern

    (2) Attach the YQPACK080SD included with the M30290T-80FPD to the NQPACK080SD-ND and secure it with the YQ-GUIDE's. (3) Attach the J1 and J2 of the M30290T-PTCB to the J3 and J4 of the M30290T-EPB. (4) Attach the M30290T-80FPD to the YQPACK080SD.
  • Page 36 M30290T-EPB User’s Manual MEMO ( 36 / 58 )

  • Page 37: Chapter 4. Usage

    Chapter 4. Usage Chapter 4. Usage This chapter describes from turning on the power of this product to starting up the emulator debugger. 4.1 Turning On the Power ..........................38 4.1.1 Checking Connections of the Emulator System................38 4.1.2 Turning ON/OFF the Power ......................38 4.1.3 Power Supply to the User System ....................

  • Page 38: Turning On The Power

    M30290T-EPB User’s Manual 4.1 Turning On the Power 4.1.1 Checking Connections of the Emulator System Before turning the power ON, check the connection of the interface cable to the host machine, PC7501, emulation probe, and user system. 4.1.2 Turning ON/OFF the Power Turn ON the power of the emulator and user system as simultaneously as possible.

  • Page 39: Led Display When The Pc7501 Starts Up Normally

    Chapter 4. Usage 4.1.4 LED Display When the PC7501 Starts Up Normally Figure 4.1 shows upper panel LED lighting status when the emulator started up properly. Check it when starting up the emulator system. ・If this LED does not light, check the voltage of the user system. ・Check that power is supplied to all the power terminals.

  • Page 40: Downloading Firmware

    M30290T-EPB User’s Manual 4.2 Downloading Firmware 4.2.1 When It is Necessary to Download Firmware It is necessary to download the firmware in the cases listed below. Normally, the following are automatically detected when the emulator debugger is started up, and the firmware is downloaded.

  • Page 41: Self-Check

    Chapter 4. Usage 4.3 Self-check 4.3.1 Self-check Procedure To run the self-check of the emulator, do so as explained here below. While the self-check is in progress, the LEDs will change as shown in Figure 4.3. (1) If the user system is connected, disconnect it. (2) Within 2 seconds of activating power to the emulator, press the system reset switch on the emulator front panel to switch the emulator to maintenance mode.

  • Page 42: If An Error Is Detected In The Self-Check

    M30290T-EPB User’s Manual 4.3.2 If an Error is Detected in the Self-check If the self-check does not result normally (ERROR 1 to ERROR 4 in Figure 4.3), check the following. Whether the emulation probe and PC7501 are connected properly. Whether the proper firmware has been downloaded.

  • Page 43: Chapter 5. Specifications

    Chapter 5. Specifications Chapter 5. Specifications This chapter describes specifications of this product. 5.1 Specifications ............................44 5.2 Connection Diagram..........................45 5.3 External Dimensions..........................46 5.3.1 External Dimensions of the Emulation Probe.................. 46 5.3.2 External Dimensions of the Converter Board M30263T-42SSB ............. 47 5.3.3 External Dimensions of the Converter Board M30260T-48FPD .............

  • Page 44: Specifications

    M30290T-EPB User’s Manual 5.1 Specifications Table 5.1 lists the specifications of the M30290T-EPB. Table 5.1 Specifications of the M30290T-EPB Emulator PC7501 Applicable MCU M16C/26A, 28, 29 Group MCUs Evaluation MCU M30290FCWP ROM: 128 KB + 4 KB, RAM: 12 KB...

  • Page 45: Connection Diagram

    Chapter 5. Specifications 5.2 Connection Diagram Figures 5.1 shows a connection diagram of the M30290T-EPB. This connection diagram mainly shows the interface section. The circuits not connected to the user system such as the emulator's control system are omitted. The signals not shown in Figure 5.1 connect the evaluation MCU and the user system directly.

  • Page 46: External Dimensions

    M30290T-EPB User’s Manual 5.3 External Dimensions 5.3.1 External Dimensions of the Emulation Probe Figure 5.2 shows external dimensions of the M30290T-EPB connected with the M30290T-PTCB. 85.0 11.0 Unit: mm Figure 5.2 External dimensions of the emulation probe ( 46 / 58 )

  • Page 47: External Dimensions Of The Converter Board M30263T-42Ssb

    Chapter 5. Specifications 5.3.2 External Dimensions of the Converter Board M30263T-42SSB Figure 5.3 shows external dimensions and a sample foot pattern of the converter board M30263T-42SSB (included with the M30263T-EPB-FP) for a 42-pin 0.8-mm-pitch SSOP. 16.00 ±0.1 35.0 +0.1 0.40 0.28 0.20 0.80...

  • Page 48: External Dimensions Of The Converter Board M30291T-64Fpd

    Figure 5.5 External dimensions and a sample foot pattern of the converter board M30291T-64FPD 5.3.5 External Dimensions of the Converter Board M30290T-80FPD Figure 5.6 shows external dimensions and a sample foot pattern of the converter board M30290T-80FPD (included with the M30290T-EPB-HP) for an 80-pin 0.5-mm-pitch LQFP. 41.0 0.25 11.1...

  • Page 49: Chapter 6. Troubleshooting

    Chapter 6. Troubleshooting Chapter 6. Troubleshooting This chapter describes how to troubleshoot when this product does not work properly. 6.1 Flowchart to Remedy the Troubles ......................50 6.2 When the Emulator Debugger Does Not Start Up Properly..............51 ( 49 / 58 )

  • Page 50: Flowchart To Remedy The Troubles

    Figure 6.1 shows the flowchart to remedy the troubles from when power to the emulator is activated until the emulator debugger starts up. Check this while the user system is disconnected. For the latest FAQs visit the Renesas Tool Homepage.

  • Page 51: When The Emulator Debugger Does Not Start Up Properly

    Chapter 6. Troubleshooting 6.2 When the Emulator Debugger Does Not Start Up Properly (1) When the LEDs of the PC7501 Shows an Error Table 6.1 Errors LEDs show and their checkpoints Connection to Error Checkpoint the user system LEDs do not light up. Check that the power cable is connected to the PC7501.
  • Page 52 M30290T-EPB User’s Manual (2) MCU Setting Dialog Box Does Not Appear at Debugger Startup Table 6.2 Checkpoints of errors at debugger startup Error Checkpoint Communication error occurred. Check that all emulator debugger settings, interface cable settings Data was not sent to the target.

  • Page 53: Chapter 7. Maintenance And Guarantee

    Chapter 7. Maintenance and Guarantee Chapter 7. Maintenance and Guarantee This chapter describes how to maintenance, repair provisions and how to request for repair. 7.1 Maintenance ............................. 54 7.2 Guarantee..............................54 7.3 Repair Provisions ............................. 54 7.4 How to Request for Repair ........................55 ( 53 / 58 )

  • Page 54: Maintenance

    M30290T-EPB User’s Manual 7.1 Maintenance If dust or dirt collects on any equipment of your emulation system, wipe it off with a dry soft cloth. Do not use thinner or other solvents because these chemicals can cause the equipment's surface coating to separate.

  • Page 55: How To Request For Repair

    Distributor After checking the contents of fault, the distributor should please send the faulty product along with the Repair Request Sheet to Renesas Solutions Corp. Renesas Solutions When the faulty product is repaired, it will be returned to the customer at the earliest convenience.
  • Page 56 M30290T-EPB User’s Manual MEMO ( 56 / 58 )
  • Page 57 M30290T-EPB User’s Manual Rev.1.00 August 16, 2004 REJ10J0388-0100Z COPYRIGHT ©2004 RENESAS TECHNOLOGY CORPORATION AND RENESAS SOLUTIONS CORPORATION ALL RIGHTS RESERVED...

Table of Contents