Raven SmarTrax Installation Manual
Case ih puma and new holland t70x0/t7.xxx - steering ready
Hide thumbs
Also See for SmarTrax:
- Calibration and operation manual (156 pages) ,
- Operation manual (73 pages) ,
- Installation manual (59 pages)
Related Manuals for Raven SmarTrax
Summary of Contents for Raven SmarTrax
- Page 1 Case IH Puma and New Holland T70X0/T7.XXX - Steering Ready SmarTrax™ Installation Manual P/N 016-5032-007 Rev B 09/15 E20796 Copyright 2012, 2013, 2015...
- Page 2 GPS, GNSS, SBAS, etc.). Therefore, Raven Industries cannot guarantee the accuracy, integrity, continuity, or availability of these services and cannot guarantee the ability to use Raven systems, or products used as components of systems, which rely upon the reception of these signals or availability of these services.
-
Page 3: Table Of Contents
Install the Node Harness ......................10 Install the Wheel Angle Sensor (WAS) Cable ................. 11 Install the Chassis Cable - SmarTrax-Only Systems (If Applicable) ........12 Connect SmarTrax to an Existing Chassis Cable (If Applicable) ..........13 Calibrate the SmarTrax System .................... - Page 4 Table of Contents Case IH Puma and New Holland T70X0/T7.XXX - Steering Ready SmarTrax™ Installation Manual...
-
Page 5: Important Safety Information
Ensure SmarTrax is disabled prior to starting any maintenance work on SmarTrax or the machine. WARNING • When starting the machine for the first time after installing SmarTrax, be sure that all persons stand clear in case a hose has not been properly tightened. •... -
Page 6: Hydraulic Safety
CAUTION Hydraulic Safety • Raven Industries recommends that appropriate protective equipment be worn at all times when working on the hydraulic system. • Never attempt to open or work on a hydraulic system with the equipment running. Care should always be taken when opening a system that has been previously pressurized. -
Page 7: Introduction
Preparing for Installation Before installing the SmarTrax system, park the machine where the ground is level, clean, and dry. Turn off the machine and leave it turned off for the duration of the installation process. Bleed pressure from the hydraulic system by loosening the hydraulic fittings slowly, where applicable. -
Page 8: Recommendations
Recommendations Raven Industries recommends the following best practices when installing or operating the SmarTrax system for the first time, at the start of the season, or when moving the SmarTrax system to another machine: • Install the GPS antenna in the recommended location. Refer to the following table for the machine-specific antenna mounting location. -
Page 9: Kit Contents
This section contains a list of the components that are included in the SmarTrax kit. Before beginning the SmarTrax installation, compare the items in the kit with the components on this list. If you have questions about the kit, contact your Raven dealer. - Page 10 Cable - Node Harness 115-4001-068 Cable - Deutsch to Tyco Adapter 115-4001-149 Cable - WAS Tee Adapter 115-4001-192 Assembly - SmarTrax Enable Foot Switch 063-0172-470 Nut - 3/8”-16 Lock 312-4001-109 Case IH Puma and New Holland T70X0/T7.XXX - Steering Ready SmarTrax™ Installation Manual...
-
Page 11: Cab Component Installation
C ab Component CHAPTER C h a p t e r 3 Installation Install the Case IH Interface Box Storage Cover Removed FIGURE 1. Remove the cover from the storage compartment in the left-rear corner of the cab. Machine’s Steering Control Cables FIGURE 2. - Page 12 Route the node harness out of the storage compartment toward the operator’s seat. Compress the foam insulation of the side wall so that the node harness fits and reinstall the storage compartment cover. Case IH Puma and New Holland T70X0/T7.XXX - Steering Ready SmarTrax™ Installation Manual...
-
Page 13: Install The Smartrax Node
Mounting Tabs When choosing the location for the SmarTrax node, consider the following points: • Mount the SmarTrax node inside the machine’s cab on a flat, level surface for proper performance and cable connection. Manual No. 016-5032-007 Rev. B... -
Page 14: Install The Foot Switch
Locate the ENABLE connector and connect it to the foot switch cable connector behind the operator’s seat. Case IH Puma and New Holland T70X0/T7.XXX - Steering Ready SmarTrax™ Installation Manual... -
Page 15: Install The Wheel Angle Sensor (Was) Cable
Cab Component Installation Steering Valve Location FIGURE 8. Route the LS PWR connector outside the cab and toward the steering valve. Note: The steering valve is located under the hood, directly in front of the cab. Valve Connection FIGURE 9. Disconnect the machine’s 2-pin connector from the load sense solenoid on the machine’s steering valve. -
Page 16: Install The Chassis Cable - Smartrax-Only Systems (If Applicable)
If the machine does not contain an existing chassis power system (such as AutoBoom, product control, etc.), it is necessary to install the chassis power cable to operate the SmarTrax system. If a CAN system already exists Case IH Puma and New Holland T70X0/T7.XXX - Steering Ready SmarTrax™ Installation Manual... -
Page 17: Connect Smartrax To An Existing Chassis Cable (If Applicable)
Cab Component Installation on the machine, refer to Connect SmarTrax to an Existing Chassis Cable (If Applicable) below to connect power to the SmarTrax system. Note: The chassis cable is sold separately. Contact your local Raven dealer for ordering information. -
Page 18: System Diagrams
Chapter 3 System Diagrams Case IH Puma and New Holland T70X0/T7.XXX - Steering Ready SmarTrax™ Installation Manual... - Page 19 Cab Component Installation Manual No. 016-5032-007 Rev. B...
- Page 20 Chapter 3 Case IH Puma and New Holland T70X0/T7.XXX - Steering Ready SmarTrax™ Installation Manual...
- Page 21 Index Cab Component Installation Calibrating the SmarTrax System 13 Connecting SmarTrax to an Existing Chassis Cable 13 Install the Wheel Angle Sensor Cable 11 Installing the Case IH Interface Box 7 Installing the Chassis Cable - SmarTrax-Only Systems 12 Installing the Foot Switch 10...
- Page 22 Index Case IH Puma and New Holland T70X0/T7.XXX - Steering Ready SmarTrax™ Installation Manual...
- Page 25 Bring the defective part and proof of purchase to your Raven dealer. If the dealer approves the warranty claim, the dealer will process the claim and send it to Raven Industries for final approval. The freight cost to Raven Industries will be the customer’s responsibility. The Return...
- Page 26 How Can I Get Service? Bring the defective part and proof of purchase to your Raven dealer. If the dealer approves the warranty claim, the dealer will process the claim and send it to Raven Industries for final approval.
Need help?
Do you have a question about the SmarTrax and is the answer not in the manual?
Questions and answers