Main Screen - Pentair EasyTouch PL4 User Manual

22
EasyTouch PL4/PSL4 Control Systems Menus
®
From the EasyTouch PL4/PSL4 Control Systems control panel menus you can schedule everyday pool/spa,
heating, filtration and cleaning. Lights and laminars can also be scheduled to switch on and off at specific
times. The "Settings" and "Schedule" menus are typically used most often for daily spa and pool operations.
The "Settings" menu is used by the pool installer to setup installed equipment which is connected to each
output relay (filter pump, auxiliary relays, heater, valves, lights, etc.). For EasyTouch PL4/PSL4 Control
Systems equipment installation instructions, see the EasyTouch PL4/PSL4 Control Systems Installation Guide
(P/N 520584).

Main Screen

AUTO HEATER
SPA 85°F / 100°F
AIR 70°F
MON 09:30 AM
AUTO HEATER
POOL 85°F / 95°F
AIR 70°F
MON 10:30 AM
AUTO
AIR 70°F
MON 11:30 AM
Main Screen Description
AUTO: The control system is in normal (automatic) operating mode. For information about "Service" and
"Timeout" operating modes, see page 4.
HEATER: The selected heat source as selected in the "Heat" menu (see page 30). The heat options are:
• OFF - No heating even though pump and other circuits may be operating.
HEATER - Gas heater only.
•
SOLAR ONLY - Solar heating system to be the only heat source. In order to display "Solar Pref." on
•
the main screen, you must first enable solar in the "Solar" menu (see page 30).
• SOLAR PREF. - (Solar Preferred) - For when solar and gas heating are combined, and you want to
use solar heating only when it is most effective. In order to display "Solar Pref." on the main screen,
you must first enable solar in the "Solar" menu.
SPA: "SPA" is displayed after the Valves (V) button is pressed to set in "spa" mode then the Filter (F) button
is pressed to switch the filter pump on, rotate the valve actuator (to isolate spa water from pool water), and
switch the heater on (if enabled in the "Heat" menu). Pressing the Valves (V) button alternates between "Pool"
and "Spa" mode. The temperature unit displayed on the left side is the actual water temperature (95° F) and
the set point temperature (100° F) as set in the "Heat" menu is displayed on the right side. If this display line
is blank, it indicates no spa or pool function is currently active. For Hi-Temp controls (single body system), see
page 30.
POOL: "POOL" is displayed after the Filter (F) button is pressed to switch the filter pump on, rotate the valve
actuator to isolate the pool water from the spa water, and switch the heater on (if enabled in the "Heat" menu).
Pressing the Valves (V) button alternates between "Pool" and "Spa" mode. The temperature unit displayed on
the left side is the actual water temperature (95° F) and the set point temperature (100° F) as set in the "Heat"
menu is displayed on the right side. If this display line is blank, it indicates no spa or pool function is currently
active. For Lo-Temp controls (single body system), see page 30.
AIR: Displays the actual outside ambient air temperature (70° F) as recorded by the air sensor located near
the EasyTouch PL4/PSL4 Control Systems Power Center.
DAY and TIME: The current system day and time (AM/PM). See the "Clock" menu to set the system day and
time (page 34).
EASYTOUCH PL4/PSL4 Control Systems User's Guide
®
The EasyTouch PL4/PSL4 Control Systems main screen displays the current mode
of operation
(AUTO/SERVICE/TIMEOUT), heat source being used, spa (or pool) actual water
temperature (95° F), current heater set point temperature (100° F) and the current
ambient air temperature (air sensor). Degree units can be displayed in either
Fahrenheit (default) or Celsius (see page 49). If the second display line is blank and
the heat source is not displayed, there is no spa or pool function currently active. The
main screen is automatically displayed if there is no control panel menu activity for
five minutes. If there is an IntelliChlor
pool and spa sanitizer settings, and salt levels can be viewed in the Diagnostics,
"Chlorinator," settings (see page 38).
Salt Chlorine Generator (SCG) being used,
®