Pentair EasyTouch PL4 User Manual page 29

AUX 1
AUX 2
AUX 3
EasyTouch PL4/PSL4 Control System Menus
®
A
FEATURE 1-2
CLOCK
SETTINGS
(OPTIONAL)
INTELLIFLO
INTELLICHLOR
(OPTIONAL)
INTELLICHEM
(OPTIONAL)
HEAT PUMP COM
(OPTIONAL)
CIRCUIT NAMES
CIRCUIT FUNC.
CUSTOM NAMES
VALVES
2-SPEED PUMP
SOLAR
DELAYS
F° / C°
iS4
QUICK TOUCH II
MAN HEAT [OFF/ON]
CALIBRATION
ERASE EEPROM
SET PASSWORD
WIRELESS ADDR
BACKLIGHT
POWER SAVE
WIRELESS ADDR
SPA SIDE [OFF/ON]
ENABLE/DISABLE IS4 SPA-SIDE REMOTE
DIAGNOSTICS SOFTWARE REV (REVISION LEVEL FOR THE OUTDOOR AND INDOOR CONTROL PANEL)
BOOTLOADER REV (REVISION LEVEL FOR THE OUTDOOR AND INDOOR CONTROL PANEL)
SELF TEST (STATUS: TESTING (FOLLOW ON-SCREEN PROMPTS TO TEST LCD AND BUTTONS) - CODE: 0 -
CHLORINATOR
WATER TEMP (FAHRENHEIT/CELCIUS - STATUS DISPLAY ONLY)
SOLAR TEMP (FAHRENHEIT/CELCIUS - STATUS DISPLAY ONLY) - (DISPLAYS IF SOLAR IS ENABLED IN HEAT MENU)
AIR TEMP (FAHRENHEIT/CELCIUS - STATUS DISPLAY ONLY)
DISP OP CODES - DISPLAY? NO/YES (DISPLAYS TRANSMIT/RECEIVE PACKETS NUMBERS ON SCREEN)
CIR NAMES [ON/OFF] VIEW DEFAULT CIRCUIT NAMES BEFORE MODIFICATION.
RESET SYSTEM (REINITIALIZE INDOOR CONTROL PANEL - USE RIGHT BUTTON)
FLASH UPDATE (USED FOR FIRMWARE UPDATES VIA PC - PRESS MENU TO ABORT)
MODE: SCHEDULE
0
08:00A -- 05:00P (12:00 AM - 11:59 PM -12 HOURS)
S M T W T F S (DAYS OF THE WEEK)
0
MODE: EGG TIMER
0
TIME: 12:00 (00:00 - 23:59) / DON'T STOP
MODE: NEW / DELETE / NONE
0
FEATURE 1 - 2
DATE & TIME 1/2 - (MONTH/DAY/YEAR) - (DAY/HOUR/MINUTES/AM/PM)
DATE & TIMER 2/2 - DAYLIGHT SAVING: (AUTO/MANUAL)
CLOCK ADJUST 00:00 (0 TO 300) - (-300 TO -5) IN 5 SCEOND INCREMENTS
PUMP #1 - PUMP TYPE [VS, VSF, NONE]
FILTERING, PRIMING, BACKWASH, VACUUM, STATUS
INTELLICHLOR 1/2 - ENABLE (YES/NO), POOL MODE: 0 - 100 % (50% default) SPA MODE: 0% (2% default)
INTELLICHLOR 2/2 - SUPER CHLR (ON/OFF), RUN HOURS (0 -72)
PH/OPR Values (pH VAL, SET - OPR VAL, SET) - Status (pH/OPR level) - Saturation Index (CH,TDS,TA,SI)
SETTINGS: ENABLE, DISABLE (NO/YES) - [HEATING, COOLING] - STATUS
CIRCUIT NAMES (1/7) - [SPA, POOL, AUX1, AUX2, AUX3, FEATURE 1-2]
CIRCUIT: (SPA [MASTER SPA], POOL [MASTER POOL], AUX 1-3, FEATURE 1-2, AUX EXTRA -
FUNCTIONS: GENERIC, MASTER SPA, MASTER POOL,
MSTR CLEANER, LIGHT, SAM LIGHT, SAL LIGHT, PHOTON GENERATOR, COLOR WHEEL,
SPILLWAY, FLOOR CLEANER, INTELLIBRITE, MAGICSTREAM,
CSTM NAME 1/7 (ASSIGN UP TO 100 CUSTOM NAMES)
[USERNAME-01...100] (UP TO 11 ALPHANUMERIC CHARACTERS)
A: [NONE, SPA, POOL, AUX1, AUX2, AUX3, FEATURE 1-2, HEATER]
B: [NONE, SPA, POOL, AUX 1, AUX2, AUX3, FEATURE 1-2, HEATER]
2-SPEED PMP 1/4 (ASSIGN UP TO 4 CIRCUITS)
CIRCUIT (NONE, SPA, POOL, AUX1, AUX2,AUX3, FEATURE 1-2, SOLAR, HEATER, POOL HEATER, SPA HEATER, FREEZE)
SOLAR 1/2 - ENABLE (YES/NO) - HEAT PUMP (YES/NO) - SOLAR 2/3 - FREEZE,
SOLAR 3/3 (TEMPREATURE DIFFERENCE) - START (3°-9° (6° default)) - RUN (2°-5° (3° default))
COOL DOWN (YES/NO) - VALVES (YES/NO)
FAHRENHEIT / CELCIUS
ASSIGN CIRCUITS 1/4
CIRCUIT - (NONE, SPA, POOL, AUX 1 - 3, FEATURE 1-2)
ASSIGN QT4 II 1/4 (ASSIGN UP TO 4 CIRCUITS)
CIRCUIT - (NONE, SPA, POOL, AUX 1 - 3, FEATURE 1-2)
SWITCH MANUAL HEAT ON OR OFF WHEN SPA IS MANUALLY SWITCHED ON (USE RIGHT BUTTON SELECT ON/OFF)
WATER (FAHRENHEIT/CELCIUS) - AIR (FAHRENHEIT/CELCIUS) - SOLAR (FAHRENHEIT/CELCIUS) -
SOLAR MUST BE ENABLED IN "HEAT" MENU TO DISPLAY
ERASE ALL (YES /NO) - ARE YOU SURE? (YES/NO)
SET PASSWORD: {XXXX} 4 DIGITS - ENABLE / DISABLE [NO/YES]
SET AN ADDRESS FOR EASYTOUCH WIRELESS CONTROL PANEL
ON TIME: 5 S, 15 S, 30 S, 60 S, 5 M, OFF [BRIGHTNESS: LOW, MED HI]
IDLE TIME: 15 S, 30 S, 60 S, 5 ME
SET AN ADDRESS FOR EASYTOUCH WIRELESS CONTROL PANEL
SEE "TROUBLESHOOTING" SECTION FOR ERROR CODES)
SALT LEVEL: DISPLAYS CURRENT SALT LEVEL (XXXX) PPM
STATUS: OK - NO ERRORS (SUPER CHLORINATE, COM LINK ERROR, CHECK FLOW / PCB,
LOW SALT, VERY LOW SALT, HIGH CURRENT, CLEAN CELL!!, LOW VOLTAGE)
(Continued)
FREEZE: NO/YES
WIRELESS CONTROL PANEL ONLY
EASYTOUCH PL4/PSL4 Control Systems User's Guide
®
21