Vitek VT-2340 Manual Instruction page 5

« ANION» button (14)
After pressing the button "
–
negative ion generator will be switched on and
the symbol " " will light up in the icon row (12).
To switch the ionization mode off touch the
–
button " ANION" (14) again, the symbol
" " in the icon row (12) will go out.
«HUMIDITY» button (15)
Relative humidity is the ratio of the mass con-
tent of water vapour in the air to the maximum
possible mass at the given temperature; relative
humidity is measured in percent and is indicated,
for example, as "45%".
Atmosphere air always contains water vapour,
percentage of which depends on meteorological
conditions; the higher the temperature, the more
water vapour is contained in the air. When cold
air is heated up to comfort temperature in winter,
relative percentage of water vapour decreases,
this is what relative humidity is.
To maintain comfortable room conditions, water
or water vapour must be artificially added to the
ambient air – this is what the air humidifier is nec-
essary for.
Comfortable relative humidity for humans is
"45-65%"; "40-55%" for preventive and medici-
nal purposes; for furniture, musical instruments
and libraries it is recommended to maintain rela-
tive air humidity of "40-60%".
Switch the humidifier on and set the required
–
level of "mist" release intensity with the button
" MIST" (16). The "mist" release intensity
will be shown with the scrolling symbols in the
icon row (12) on the panel (6).
Repeatedly touch the button "
–
(15) to set the desired level of relative humidity
in the room within the range from 30% to 90%
with the step of 5%, the humidity level is shown
with the digital symbols (11) and the symbol "
" in the icon row (12) on the panel (6).
After reaching the preset humidity level the
–
"mist" release will be switched off, the "mist"
release intensity in the icon row (12) will go
out. If the humidity level in the room decreases
the "mist" release will switch on again, and the
"mist" release intensity symbols in the icon
row (12) on the panel (6) will light up.
To switch the selected humidity maintenance
–
mode off press the button "
(15) until the symbol «
the panel (6) goes out, the digital symbols (11)
will show the relative humidity and the sym-
bols (10) will show the room temperature.
IM VT-2340.indd 5
Water heating mode on/off button
"
ANION" (14) the
In the water heating mode the evaporable water
is heated up to approximately 40°С, which helps
to disinfect the water and facilitates its evapo-
ration.
–
–
Timer setting button "
–
–
–
«Night» mode on/off button "
–
HUMIDITY"
–
Low water level indication
–
–
HUMIDITY"
» in the icon row on
–
5
WARM MIST" (17)
Press the button « WARM MIST» (17) to
switch the water heating mode on, the sym-
bol « » will light up in the icon row (12) on
the panel (6).
To switch the water heating mode off press
the button " WARM MIST" (17) again,
the water heating symbol "
row (12).
Consequently press the button "
(18) to set up the timer within the range from
1 to 12 hours with 1 hour step which will be
shown as the digital symbols (10) on the con-
trol panel (6) and the symbol "
row (12).
When the set time is reached the air humidifier
will be switched off.
To switch the time off press the button
" TIMER" until the symbol "
row (12) goes out, the digital symbols (10) will
show the room temperature.
After you press the button "
the air humidifier will switch to the "night"
mode, the symbol " " will light up in the
icon row (12), the symbols brightness on
the panel (6) will decrease and the operat-
ing mode buttons (14, 15, 16, 17, 18, 19) will
be inactive.
In the "night" mode you can switch the humid-
ifier off by pressing the button "
(13) or switch off the "night" mode by pressing
the button " SLEEP" (19) again.
When the water tank (3) is empty, the unit will
be switched off, you will hear sound signals
and the symbol " " will light up red and start
flashing in the icon row (12).
Switch the humidifier off by pressing the but-
ton " ON/OFF" (13) and unplug it, remove
the nozzle (1) and the water tank (3). Fill the
water tank (3) with water and install it on the
humidifier body (9), install the nozzle (1) back
to its place.
Switch the humidifier on for further operation.
ENGLISH
" in the icon
TIMER" (18)
TIMER"
" in the icon
" in the icon
SLEEP" (19)
SLEEP" (19)
ON/OFF"
18.01.2019 10:20:56