2Nd.level.programming - FAAC 624BLD Manual

Display Function
L 2
LOOP 2:
If you activate this function, the loop
connected to Loop input will have the
SAFETY /CLOSE function, i.e. it will operate
as SAFETY during the closing stage, and will
command CLOSE to the board at release.
Y
= loop active
n o
= loop not active
Attention: if the function is not activated, loop
status will nevertheless be available on one of the
outputs, if appropriately set
S 1
NO EFFECT
S2
NO EFFECT
S t
AUTOMATED SYSTEM STATUS:
Exit from programming, storage of set data
and return to automated system status
view.
00
Closed
0 1
Opening pre-flashing
02
Opening
03
Open
04
On pause
05
Closing pre-flashing
06
Closing
07
Stopped ready to close
08
Stopped ready to open
09
Emergency opening
10
Closing safety device in operation
5.2.. 2 LEVEL.PROGRAMMING
nd.
To access  LEVEL PROGRAMMING, press push-button F and, while
ND
holding it down, press push-button +.
• if you release the push-button +, the display shows the name
of the first function.
• if you also release the F push-button, the display shows the
value of the function, which can be changed with keys +
and -.
• if you press the F key (and hold it down), the display shows
the name of the next function; if you release it, the value is
shown and can be modified with keys + and -.
• when you reach the last function, press the F push-button
to exit programming, and the display resumes showing the
inputs status.
The following table indicates the sequence of functions accessible in
nd LEVEL PROGRAMMING:
2 LEVEL PROGRAMMING
nd
Display Function
bo
MAXIMUM TORQUE AT THRUST:
the motor works at maximum torque
(ignoring the torque adjustment) during
the initial time of the movement.
Y
= Active
no
= Excluded
PF
PRE-FLASHING:
to activate the flashing light for 5 sec
before the start of the movement
no
OC
before every movement
PA
at end of pause only
CL
before closing
Default
.
Default
excluded
Display Function
SC
SLOW CLOSING:
no
for setting the entire closing stage at slow
speed.
tr
DECELERATION TIME AFTER LIMIT-SWITCHES:
for setting deceleration time (in seconds)
after the opening and closing limit-switches
have operated.
Can be adjusted from
second steps.
t
WORK TIME (time-out):
We advise you to set a value from 5 to 0 se-
05
conds longer than the required by the au-
tomated system to move from the closing
to the
Can be adjusted from
05
second steps.
Next, the viewing changes in minutes and ten-
ths of a second (separated by a dot) and time is
adjusted in 0 second steps, up to the maximum
value of
FS
FAIL SAFE:
If this function is activated, it enables a
function test of the photocells before any
automated system movement, indepen-
dently from the output used . If the test fai-
ls , the automated system does not start
the movement.
o 1
OUTPUT 1:
The output can be set to one of the fol-
lowing functions:
00
01
ning and pause, flashing at closing, and
off when automated system closed)
02
beam closed and on pause, inactive with
beam open, flashing during movement)
03
04
OFF during closing pre-flashing.
05
pre-flashing included.
06
pre-flashing included.
07
08
09
10
1 1
12
13
14
15
16
17
18
P1
OUTPUT 1 POLARITY:
for configuring the output polarity status.
Note: if the output is set to FAIL-SAFE (
leave the default value.
Y
o2
OUTPUT 2:
See output 
P2
OUTPUT 2 POLARITY:
See output  polarity
no
o3
OUTPUT 3:
See output 
P3
OUTPUT 3 POLARITY:
See output  polarity
7
Y
= Active
no
= Excluded
0 10
to sec. in one
00
= deceleration excluded
10
= maximum deceleration
opening position and vice versa.
0 59
to sec. in one
4.1
minutes.
Y
= Active
no
= Excluded
FAILSAFE
INDICATOR LIGHT (lighted at ope-
BEAM LIGHTING (output active with
L I G H T E
Beam CLOSED
Beam OPEN or in PAUSE, it goes
Beam MOVING AT OPENING,
Beam MOVING AT CLOSING,
Beam STILL
Beam in EMERGENCY status
LOOP engaged
LOOP engaged
OPEN for 64 SLAVE
CLOSE for 64 SLAVE
Beam DETACHED
FAAC - CITY lights
FAAC - CITY buzzer
FCA engaged
FCC engaged
interlock
Y
= N.C. polarity
n o
= N.O. polarity
Default
no
03
20
no
00
no
00
)
03
no
01
no