Advertisement
© BOSTITCH 2019
TRIGGER LOCKOUT CONTROL -
DA1564K-E ONLY (FIG 7, 8)
GB Not to be reproduced without permission. Unauthorised copies of this document do not constitute CE
The trigger lockout control feature on BOSTITCH
compliance for the products.
pneumatic tools provides a trigger lock feature for added
safety control. Push the Lockout control button in or out
FR Reproduction interdite sans permission préalable. Les copies non autorisées de ce document ne signifient en
to activate or lock the tool trigger.
rien que les produits soient conformes aux normes CE.
ACTUATION MODE
DE Vervielfältigung nicht ohne Genehmigung gestattet. Unzulässig erstellte Kopien dieses Dokuments erfüllen nicht
m Warning! Always disconnect air supply before making
die CE-Richtlinien für Produkte.
adjustments as accidental actuation may occur, possibly
causing injury.
NL Mag niet worden vermenigvuldigd zonder toestemming. Onrechtmatige kopieën van dit document willen niet
zeggen dat de producten voldoen aan de CE-vereisten.
SAFETY YOKE TYPE - N62FNSP-E ONLY
DK Må ikke gengives uden tilladelse. Uautoriserede kopier af dette dokument udgør ikke CE overholdelse for
These models operate differently from all other
BOSTITCH tools. To provide maximum visibility for
produkterne.
accurate fastener placement, the safety yoke of this tool
is normally in the "depressed" or "up" position. On all
FI Ei saa jäljentää ilman lupaa. Tämän asiakirjan ilman valtuutusta tehdyt kopiot eivät muodosta tuotteille CE-
other BOSTITCH tools and most other tools, the safety
yhdenmukaisuutta.
yoke is normally in the "extended" or "down" position.
This tool has a selectable actuation mode which
GR Απαγορεύεται η αναπαραγωγή χωρίς προηγούμενη άδεια. Τα μη εξουσιοδοτημένα
determines if the tool drives fasteners in sequential or
αντίγραφα του παρόντος εγγράφου δεν αποτελούν συμμόρφωση CE για τα προϊόντα.
contact actuation mode. In sequential mode, when the
tip of the nose is placed on the work surface and the
IT Vietata la riproduzione senza permesso. Le copie non autorizzate di questo documento non garantiscono la
trigger is pulled, the safety yoke moves out from the tool
to detect the work surface. The tool nose tip must be in
conformità CE per i relativi prodotti.
contact with the work surface to actuate. If the safety
yoke does not detect the work surface close enough to
NO Skal ikke reproduseres uten tillatelse. Ikke godkjente kopier av dette dokumentet oppfyller ikke kravene for
the nose of the tool, the tool will not actuate.
CE-merking for produktet.
In contact actuation mode, when the trigger is depressed
and held, the safety yoke will move out from the tool.
PT Reprodução proibida sem autorização prévia. As cópias não autorizadas deste documento não estão em
Contacting the work surface with the tool nose, will
conformidade com a CE para os produtos.
actuate the safety yoke driving a fastener each time the
work surface is contacted.
ES Prohibida la reproducción sin permiso. Las copias no autorizadas de este documento no suponen la
conformidad con las normas CE de los productos.
SELECTABLE ACTUATION SYSTEM - ALL MODELS
These models feature a selectable actuation system that
SE Prohibida la reproducción sin permiso. Las copias no autorizadas de este documento no suponen la
allows the user to choose between the following modes
conformidad con las normas CE de los productos.
of operation.
m WARNING! Tools marked with this symbol
PL Niniejszy dokument nie może być kopiowany bez pozwolenia. Nieautoryzowane kopie niniejszego dokumentu
have either contact actuation, continuous
nie stanowią deklaracji zgodności CE prezentowanych produktów.
contact actuation or selectable actuation
with contact actuation selected.
CZ Niniejszy dokument nie może być kopiowany bez pozwolenia. Nieautoryzowane kopie niniejszego dokumentu
WHEN IN CONTACT ACTUATION MODE:
nie stanowią deklaracji zgodności CE prezentowanych produktów.
These tools are designed for use in production
applications such as pallets, furniture,
SK Rozmnožovanie bez povolenia je zakázané. Neoprávnené kópie tohto dokumentu nie sú v súlade s CE pre dané
manufactured housing or upholstery.
výrobky.
DO NOT use for applications such as closing boxes
or crates and fitting transportation safety systems
on trailers and lorries. This tool shall only be used in
HU A dokumentum engedély nélkül nem sokszorosítható. Az engedély nélkül sokszorosított dokumentum nem
safe working places. Care must be taken to prevent
jelenti a termék CE-megfelelőségét.
accidental actuation when changing from one
working position to another.
RO Reproducerea neautorizată este interzisă. Copiile neautorizate ale acestui document nu reprezintă
conformitatea CE pentru produse.
SEQUENTIAL ACTUATION
The sequential actuation requires the operator to hold
the tool against the work with the safety yoke depressed
before pulling the trigger. In order to drive additional
fasteners, the trigger must be released and the tool
lifted away from the work, before repeating the above
mentioned steps.
This makes accurate fastener placement easier, for
instance on framing, toe nailing and crating applications.
The sequential actuation allows exact fastener location
without the possibility of driving a second fastener on
recoil, as described under Contact Trip (below). The
sequential actuation tool has a positive safety advantage
because it will not accidentally drive a fastener if the tool
is contacted against the work - or anything else - while
the operator is holding the trigger pulled.
CONTACT ACTUATION
The common operating procedure on "Contact
actuation" tools is for the operator to actuate the
safety trip while keeping the trigger pulled, thus driving
a fastener each time the work is contacted. This will
allow rapid fastener placement on many jobs, such as
sheathing, decking and pallet assembly. All pneumatic
tools are subject to recoil when driving fasteners.
The tool may bounce, releasing the safety yoke and
if unintentionally allowed to re-contact the work
surface with the trigger still actuated (finger still
holding the trigger pulled) an unwanted second
fastener will be driven.
SELECTING THE ACTUATION MODE (FIG 9-10):
To ensure safety, the user should lock the trigger
(DA1564K-E ONLY - see Trigger Lockout Control
above) before changing the trigger system. To
change the actuation mode, rotate the switch in the
counterclockwise direction. The switch will lock
automatically when the indicating arrow is pointing down
to the 3 nail icon stamped into the tool frame (Contact
Actuation Mode) or to a single nail icon stamped in the
tool frame (Sequential Actuation Mode). Unlock the
trigger to resume tool operation.
"DIAL-A-DEPTH™" FASTENER CONTROL
ADJUSTMENT (FIG 11A / 11B)
The DIAL-A-DEPTH™ Fastener Control adjustment
feature provides close control of the fastener drive depth;
from flush with the work surface to shallow or deep
countersink. First, set the air pressure for consistent
drive in the specific work, then use the DIAL-A-DEPTH™
Fastener Control adjustment to give the desired depth
of drive.
GB
9
Advertisement
