Bostitch N52FN Operation And Maintenance Manual
  1. Manuals
  2. Brands
  3. Bostitch Manuals
  4. Nail Gun
  5. N52FN
  6. Operation and maintenance manual

Bostitch N52FN Operation And Maintenance Manual

Industrial oil free angled finish nailers
Hide thumbs Also See for N52FN:

Advertisement

Table of Contents

See also: Operation & Maintenance Manual
N52FN/N62FN
INDUSTRIAL OIL FREE ANGLED FINISH NAILERS
CLAVADORA INDUSTRIAL EN BARRA ANGULA LIBRE DE LUBRICACIÓN
CLOUEURS INDUSTRIEL DE FINITION EN BANDES SANS HUILE
OPERATION and MAINTENANCE MANUAL
MANUAL DE OPERACIÓN Y DE MANTENIMIENTO
MANUEL D'INSTRUCTIONS ET D'ENTRETIEN
BEFORE OPERATING THIS TOOL, ALL OPERATORS SHOULD STUDY THIS MANUAL TO
UNDERSTAND AND FOLLOW THE SAFETY WARNINGS AND INSTRUCTIONS. KEEP THESE
INSTRUCTIONS WITH THE TOOL FOR FUTURE REFERENCE. IF YOU HAVE ANY QUESTIONS,
CONTACT YOUR BOSTITCH REPRESENTATIVE OR DISTRIBUTOR.
ANTES DE OPERAR ESTA HERRAMIENTA, TODOS LOS OPERADORES DEBERÁN ESTUDIAR
ESTE MANUAL PARA PODER COMPRENDER Y SEGUIR LAS ADVERTENCIAS SOBRE SEGURI-
Y LAS INSTRUCCIONES. MANTENGA ESTAS INSTRUCCIONES CON LA HERRAMIENTA
PARA FUTURA REFERENCIA, SI TIENE ALGUNA DUDA, COMUNÍQUESE CON SU REPRESEN-
DE BOSTITCH O CON SU DISTRIBUIDOR.
LIRE ATTENTIVEMENT LE PRÉSENT MANUEL AVANT D'UTILISER L'APPAREIL. PRÉTER UNE
ATTENTION TOUTE PARTICULIÈRE AUX CONSIGNES DE SÉCURITÉ ET AUX AVERTISSE-
GARDER CE MANUEL AVEC L'OUTIL POUR FUTUR RÉFÉRENCE. SI VOUS AVEZ DES
QUESTIONS, CONTACTEZ VOTRE REPRÉSENTANT OU VOTRE CONCESSIONNAIRE BOSTITCH.
107740REVD 12/00
Stanley Fastening Systems

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the N52FN and is the answer not in the manual?

Questions and answers

Related Manuals for Bostitch N52FN

Summary of Contents for Bostitch N52FN

  • Page 1 LIRE ATTENTIVEMENT LE PRÉSENT MANUEL AVANT D’UTILISER L’APPAREIL. PRÉTER UNE ATTENTION TOUTE PARTICULIÈRE AUX CONSIGNES DE SÉCURITÉ ET AUX AVERTISSE- GARDER CE MANUEL AVEC L’OUTIL POUR FUTUR RÉFÉRENCE. SI VOUS AVEZ DES QUESTIONS, CONTACTEZ VOTRE REPRÉSENTANT OU VOTRE CONCESSIONNAIRE BOSTITCH. 107740REVD 12/00 Stanley Fastening Systems...

  • Page 2: Table Of Contents

    Bostitch nails, staples and accessories. LIMITED WARRANTY Bostitch, Inc., warrants to the original retail purchaser that this product is free from defects in material and workmanship, and agrees to repair or replace, at Bostitch's option, any defective product within 1 year from the date of purchase. This warranty is not transferable. It only covers...

  • Page 3: Safety Instructions

    SAFETY INSTRUCTIONS EYE PROTECTION which conforms to ANSI specifications and provides protection against flying particles both from the FRONT and SIDE should ALWAYS be worn by the operator and others in the work area when loading, operating or servicing this tool. Eye protection is required to guard against flying fasteners and debris, which could cause severe eye injury.
  • Page 4 PRESSURE. AIR CONSUMPTION: Model N52FN requires 4.0 cubic feet per minute and Model N62FN requires 5.3 cubic feet per minute of free air to operate at the rate of 60 fasteners per minute, at 80 p.s.i.g. To calculate the actual rate at which the tool will be run to determine the amount of air required, for example;...

  • Page 5: Air Supply And Connections

    AIR SUPPLY AND CONNECTIONS Do not use oxygen, combustible gases, or bottled gases as a power source for this tool as tool may explode, possibly causing injury. FITTINGS: Install a male plug on the tool which is free flowing and which will release air pressure from the tool when disconnected from the supply source.
  • Page 6 LOADING THE N52FN/N62FN EYE PROTECTION which conforms to ANSI specifications and provides protec- tion against flying particles both from the FRONT and SIDE should ALWAYS be worn by the operator and others in the work area when loading, operating or ser- vicing this tool.

  • Page 7: Tool Operation

    THIS MANUAL. II. REFER TO “TOOL SPECIFICATIONS” IN THIS MANUAL TO IDENTIFY THE OPERATING SYSTEM ON YOUR TOOL. There are three available systems on BOSTITCH pneumatic tools. They are: 1. TRIGGER OPERATION 2. CONTACT TRIP OPERATION 3. SEQUENTIAL TRIP OPERATION OPERATION 1.

  • Page 8: Tool Operation Check

    IN ADDITION TO THE OTHER WARNINGS CONTAINED IN THIS MANU- AL OBSERVE THE FOLLOWING FOR SAFE OPERATION • Use the BOSTITCH pneumatic tool only for the purpose for which it was designed. • Never use this tool in a manner that could cause a fastener to be directed toward the user or others in the work area.

  • Page 9: Maintaining The Pneumatic Tool

    Care must also be taken to insure no permanent kinks are put in the spring as this will reduce the springs force. REPLACEMENT PARTS: BOSTITCH replacement parts are recommended. Do not use modified parts or parts which will not give equivalent performance to the original equipment. AIR SUPPLY-PRESSURE AND VOLUME: Air volume is as important as air pressure.

  • Page 10: Trouble Shooting

    TROUBLE SHOOTING PROBLEM CAUSE CORRECTION Trigger valve housing leaks air O-ring cut or cracked ....Replace O-ring Trigger valve stem leaks air O-ring/seals cut or cracked ..Replace trigger valve assembly Frame/nose leaks air Loose nose screws .

  • Page 11: Dial-A-Depth™ Fastener Control Adjustment

    TO ADJUST DIAL-A DEPTH FASTENER TRIP ADJUSTMENT CONTROL ADJUSTMENT: Deep JAM RELEASE Models N52FN and N62FN, contain a Jam Release feature. ALWAYS DISCONNECT AIR SUPPLY BEFORE CLEARING A JAMMED FASTENER. Jam Clearing Partial Release Of Magazine Disconnect air supply from tool.

  • Page 12: Accessories

    ACCESSORIES AVAILABLE: N80K2 Remote Cycle Kit N62-MAGKIT N62 Magazine Assembly Kit IMPORTANT NOTE: Steel finish nails are made from galvanized steel wire and not treated after nails are manufactured. As such, we do not guarantee or warranty product against corrosion for any specified time. -12-...

This manual is also suitable for:

N62fn

Table of Contents