Advertisement
© BOSTITCH 2019
INTEGRATED AIR BLOWER (FIG 12, 13)
The N62FNSP-E / DA1564K-E has a integrated air
GB Not to be reproduced without permission. Unauthorised copies of this document do not constitute CE
blower that helps clean debris while working. Press the
compliance for the products.
integrated air blower button. Compressed air will be
GB
ejected out from front of the tool. Released the button to
FR Reproduction interdite sans permission préalable. Les copies non autorisées de ce document ne signifient en
stop blowing air.
rien que les produits soient conformes aux normes CE.
DO NOT DIRECT AIR STREAM AT BODY Risk of injury, do
not direct air stream at persons or animals.
DE Vervielfältigung nicht ohne Genehmigung gestattet. Unzulässig erstellte Kopien dieses Dokuments erfüllen nicht
die CE-Richtlinien für Produkte.
LED WORKLIGHT - DA1564K-E ONLY (FIG 14, 15, 16)
NL Mag niet worden vermenigvuldigd zonder toestemming. Onrechtmatige kopieën van dit document willen niet
NOTE: The LED worklight and battery is supplied
and fitted as a single component and cannot be
zeggen dat de producten voldoen aan de CE-vereisten.
serviced. If the LED or battery needs to be
replaced, a new unit should be fitted.
DK Må ikke gengives uden tilladelse. Uautoriserede kopier af dette dokument udgør ikke CE overholdelse for
•
DO NOT dispose of this unit with household waste.
produkterne.
•
Always dispose of batteries according to
local legislation.
FI Ei saa jäljentää ilman lupaa. Tämän asiakirjan ilman valtuutusta tehdyt kopiot eivät muodosta tuotteille CE-
yhdenmukaisuutta.
•
Please recycle in line with local provisions for
the collection and disposal of electrical and
GR Απαγορεύεται η αναπαραγωγή χωρίς προηγούμενη άδεια. Τα μη εξουσιοδοτημένα
electronic waste.
αντίγραφα του παρόντος εγγράφου δεν αποτελούν συμμόρφωση CE για τα προϊόντα.
This component is excluded from any extended warranty
and will operate for approx. 100,000 tool cycles.
IT Vietata la riproduzione senza permesso. Le copie non autorizzate di questo documento non garantiscono la
conformità CE per i relativi prodotti.
OPERATION
To operate the LED work-light you must first remove an
NO Skal ikke reproduseres uten tillatelse. Ikke godkjente kopier av dette dokumentet oppfyller ikke kravene for
electricity isolated plastic sheet before using the LED
work-light.
CE-merking for produktet.
1. Pull up the nose cover to open.
PT Reprodução proibida sem autorização prévia. As cópias não autorizadas deste documento não estão em
2. Pull out the electricity isolated plastic sheet.
conformidade com a CE para os produtos.
3. Close the nose cover.
4. LED light is on/off by pressing light button on the cover.
ES Prohibida la reproducción sin permiso. Las copias no autorizadas de este documento no suponen la
conformidad con las normas CE de los productos.
REMOVING THE LIGHT (Fig 17, 18, 19)
SE Prohibida la reproducción sin permiso. Las copias no autorizadas de este documento no suponen la
The LED work-light can be easily removed or if needed.
conformidad con las normas CE de los productos.
1. Pull up the nose cover to open
2. Press on the snap-fitting hook to release LED work-light.
PL Niniejszy dokument nie może być kopiowany bez pozwolenia. Nieautoryzowane kopie niniejszego dokumentu
3. Take out the LED work-light from the cover.
nie stanowią deklaracji zgodności CE prezentowanych produktów.
REPLACING THE LIGHT (N62-LED) (Fig 20, 21, 22)
CZ Niniejszy dokument nie może być kopiowany bez pozwolenia. Nieautoryzowane kopie niniejszego dokumentu
Insert a new LED work-light.
nie stanowią deklaracji zgodności CE prezentowanych produktów.
1. Align housing of the LED work-light into nose cover until
it snaps into position. Make sure the button is placed
SK Rozmnožovanie bez povolenia je zakázané. Neoprávnené kópie tohto dokumentu nie sú v súlade s CE pre dané
through nose cover hole.
výrobky.
2. Pull out the elecricity isolated plastic sheet.
HU A dokumentum engedély nélkül nem sokszorosítható. Az engedély nélkül sokszorosított dokumentum nem
3. Close the nose cover.
jelenti a termék CE-megfelelőségét.
RO Reproducerea neautorizată este interzisă. Copiile neautorizate ale acestui document nu reprezintă
conformitatea CE pentru produse.
10
JAM CLEARANCE (FIG 23-28)
m Warning! Always disconnect the air before clearing a
jammed fastener.
1. Disconnect the tool from the air supply. (Fig 23)
2. Release the pusher so it is no longer applying force to
the nail sticks. (Fig 24)
3. Open the jam clearing nose door by pulling down and
then up on the latch. (Fig 25)
4. Remove the jammed fastener. In certain circumstances,
pliers may be required to remove the fastener. (Fig 26)
5. Close the jam clearing nose door latch. (Fig 27)
6. Pull nail pusher back behind nail sticks. (Fig 28)
Advertisement
