Respironics BiPAP Plus User Manual page 45

a a: emC I
ppendIx
g m
uIdanCe and anufaCturer
electrmagnetic environment specified below. The user of this device should make sure it is used in such an environment.
e t
mIssIons est
RF emissions
CISPR 11
RF emissions
CISPR 11
Harmonic emissions
IEC 61000-3-2
Voltage fluctuations/Flicker emissions
IEC 61000-3-3
g m
uIdanCe and anufaCturer
electromagnetic environment specified below. The user of this device should make sure it is used in such an environment.
I t
mmunIty est
Electrostatic Discharge (ESD)
IEC 61000-4-2
Electrical Fast Transient/Burst
IEC 61000-4-4
Surge
IEC 61000-4-5
Voltage dips, short
interruptions and voltage
variations on power supply
input lines
IEC 61000-4-11
Power frequency (50/60 Hz)
magnetic field
IEC 61000-4-8
NOTE: U is the a.c. mains voltage prior to application of the test level.
T
B pap p m s u
I lus erIes
nformatIon
' d - e
s eClaratIon leCtromagnetIC
C
omplIanCe
Group 1
Class B
Class A
Complies
' d - e
s eClaratIon leCtromagnetIC
IeC 60601 t
est
l
evel
±6 kV contact
±8 kV air
±2 kV for power supply lines
±1 kV for input-output lines
±1 kV differential mode
±2 kV common mode
<5% U
T
(>95% dip in U ) for 0.5 cycle
T
40% U
T
(60% dip in U ) for 5 cycles
T
70% U
T
(30% dip in U ) for 25 cycles
T
<5% U
T
(>95% dip in U ) for 5 sec
T
3 A/m
m
ser anual
e :
This device is intended for use in the
mIssIons
e
leCtromagnetIC
The device uses RF energy only for its internal function. Therefore, its
RF emissions are very low and are not likely to cause any interference
in nearby electronic equipment.
The device is suitable for use in all establishments, including
domestic establishments and those directly connected to the public
low-voltage power supply network.
I :
mmunIty This device is intended for use in the
C l
omplIanCe evel
±6 kV contact
±8 kV air
±2 kV for supply mains
±1 kV for input/output lines
±1 kV differential mode
±2 kV for common mode
<5% U
T
(>95% dip in U ) for 0.5 cycle
T
40% U
T
(50% dip in U ) for 5 cycles
T
70% U
T
(30% dip in U ) for 25 cycles
T
<5% U
T
(>95% dip in U ) for 5 sec
T
3 A/m
e - g
nvIronment uIdanCe
e e
leCtromagnetIC nvIronment
g
uIdanCe
Floors should be wood, concrete or ceramic
tile. If floors are covered with synthetic
material, the relative humidity should be at
least 30%.
Mains power quality should be that of a
typical home or hospital environment.
Mains power quality should be that of a
typical home or hospital environment.
Mains power quality should be that of a
typical home or hospital environment. If
the user of the device requires continued
operation during power mains interruptions,
it is recommended that the device be
powered from an uninterruptible power
supply or a battery.
Power frequency magnetic fields should be
at levels characteristic of a typical location in
a typical hospital or home environment.
-
A-1