Diagnostic; Osd Menu Setting; Osd Menu Table - Ganz ZT-PTS Series Instruction Manual

Diagnostic

Whenever the IR Camera is power on, a standard diagnostic is operated.
CAMERA ID : 001
BAUD RATE : 2400BPS
WAITING............
A. PAN Origin Test
Zero point of Pan is Located during the Panning test.
B. Tilt Origin Test
Zero point of Tilt is Located during the Tilt Test
C. TX Connection Test
Wait for 60 seconds for TX Connection Test.
During 60 seconds, the camera is must received a signal by any control
equipment as DVR or controller.
Then OK is displayed then automatically verifying TX Connection Test
• If "Not Tested" is displayed in the test.
- The result which is not received any signal from DVR or controller.
- Wrong connecting way such as the protocol, baud rate or RS-485
connection.
The use may check the install way carefully.
D. Camera Comm. Test
Camera communication is also checked.
OK should be displayed in these four tests before installation.
If all the above Tests are OK, "NOW EEPROM CHECKING" and "ALL DATA
INITIALIZING" is displayed and the camera is ready to operate.
ZT-PTS SERIES
PAN ORIGIN TEST OK
TILT ORIGIN TEST OK
TX CONNECTION TEST OK
CAMERA COMM TEST OK
016

OSD Menu Setting

A. OSD Menu Table
MAIN MENU
DOME SETUP CAMERA ID
CAMERA SET RECOVER
PRESET MANUAL SPEED : 150℃
AUTO SCAN ALARM
TOUR LANGUAGE
PATTERN [NEXT PAGE]
ALARM SAVE AND EXIT
SECTOR EXIT
EXIT
CAMERA SET
COLOR MODE : B/W PRESET NO
INVERS MODE : OFF PRESET ID
D-ZOOM : OFF PAN : XXX.X
AGC MODE : ON SAVE
AGC MAX LEVEL : x1.5 EXIT
T-RANGE MIN : 020℃
T-RANGE MAX : 045℃
CALI. MODE : AUTO
CALI. INTERVAL : 600SEC
EXIT
AUTO SCAN SET
START ANGLE : XXX.X.XXX.X TOUR NO
END ANGLE : XXX.X.XXX.X TOUR TITLE
DIRECTION : CW TOUR STEP
ENDLESS : OFF / ON PRESET NO
SPEED : 10°/S DWELL TIME
DWELL TIME : 03 SPEED
SAVE AND EXIT SAVE
EXIT EXIT
PATTERN SET
PATT NO : 01 ALARM NO
PATT TITLE : PATTERN 01 ALARM INPUT
DATE FILL : 100% ALARM ACT
SAVE AUX ACT
EXIT SAVE
EXIT
SECTOR
SECTOR NO : 01
SECTOR ID : SECTOR01
SECTOR START : XXX.X.XX.X
SECTOR END : XXX.X.XX.X
SAVE
EXIT
ZT-PTS SERIES
DOME SET DOME SET
: CAM 1 [SYSTEM SET]
: OFF SYSTEM LOCK : OFF
[PASSWORD]
: DISABLE [OSD DISPLAY]
: ENGLISH [SYSTEM STATUS]
[INITIALIZATION]
[PREVIOUS PAGE]
PRESET SET SYSTEM SET
: 01 FLIP STATUS : NOMAL
: PRESET 01 MOTOR TORQUE : LOW
TITL : XX.X RECOVER ORIGIN : ON
[PREVIOUS PAGE]
TOUR SET OSD DISPLAY
: 01 CAMERA ID : ON / OFF
: TOUR 01 PRESET ID : ON / OFF
: 01 SECTOR ID : OFF / ON
: 01 COORDINATE : ON / OFF
: 03 [PREVIOUS PAGE]
: 200°/S
ALARM SET [SYSTEM STATUS]
: 01 PROTOCOL : PELCO D/P
: OFF / ON / NC BAUD RATE : 2400BPS
: 001 FIRMWARE VER : 1.10a
: BLK UPGRADED DATE : 02.02.12
CAMERA MODULE: TSM-72
[PREVIOUS PAGE]
[INITIALIZATION]
[TOUR CLEAR]
[PRESET CLEAR]
[SECTOR CLEAR]
[PATTERN CLEAR]
[LOAD OPTIMIZED DEFAULT]
[PREVIOUS PAGE]]
017