Advertisement
Quick Links
©2015 FarmTek
®
All Rights Reserved. Reproduction
is prohibited without permission.
Revision date: 08.26.15
6' Wide Premium Greenhouse Benches
Premium Greenhouse Bench with Stationary Top
STK#
DIMENSIONS
112416S6X08
6' W x 3' H x 8' L
112416S6X10
6' W x 3' H x 10' L
112416S6X12
6' W x 3' H x 12' L
*
Actual bench may differ from example shown.
1
Advertisement
Related Manuals for FarmTek Growers Supply 112416S6X10
Summary of Contents for FarmTek Growers Supply 112416S6X10
- Page 1 6' W x 3' H x 8' L 112416S6X10 6' W x 3' H x 10' L 112416S6X12 6' W x 3' H x 12' L ©2015 FarmTek ® All Rights Reserved. Reproduction Actual bench may differ from example shown. is prohibited without permission.
-
Page 2: Important Information
Important Information READ THIS DOCUMENT BEFORE YOU BEGIN Thank you for purchasing this premium greenhouse bench. When properly assembled and maintained, this product will provide years of reliable service. These instructions include helpful hints and important information needed to safely assemble and properly maintain the bench. Please read these instructions before you begin. - Page 3 Important Information PICTORIAL GUIDE The following graphics and photos will help identify the different parts of your bench. (Some parts may not be shown.) 102921B FALB10B FAG102B FA4482B 108553 Wafer 100442 (1) QH1070 Pipe Neo-Bonded 1/4" Nut 1/4" x 3/4" Bolt Tek Screw Head Screw Nut Setter...
-
Page 4: Assembly Instructions
Assembly Instructions ASSEMBLE BENCH TOP SUPPORTS Use the photos and information that follows to construct the bench top frame supports. The 12' bench has four (4) support assemblies. The 8' and 10' benches each have three (3) supports. Gather the parts required to complete one (1) support assembly: •... - Page 5 Assembly Instructions 6. Tighten 1/4" bolts. 7. Check square tube position. 8. Install one FA4482B Tek screw in center. 9. Check assembly for square. 10. Secure bracket in place using two (2) 11. Flip assembly over and repeat Steps 8-10 more Tek screws.
- Page 6 Assembly Instructions ATTACH PIPE STRAPS Use the photos and information that follows to attach the QH1070 straps. Attach two QH1070 straps to each bench top support assembly. QH1070 1. Measure 15-3/4" from the bottom of each leg 2. Have an assistant hold the assembly and 3.
- Page 7 Assembly Instructions ASSEMBLE SUPPORT FRAME FOR BENCH TOP For best results, assemble the support frame on a flat, level surface. Gather the parts for the support frame: • (6) ST01500D706G19 struts; eight (8) for the 12' bench. • (2) 1.315" diameter round pipes. (See Quick Start diagrams for pipe length/ID.) •...
- Page 8 Assembly Instructions ASSEMBLE SUPPORT FRAME FOR BENCH TOP—continued 7. Tighten the pipe strap mounting bolts of 8. Check that six (6) band clamps are in position 9. Take one strut and attach it to one band clamp. the mid support. Tighten until snug. Do not on the horizontal pipes–eight (8) for the 12' overtighten.
- Page 9 Assembly Instructions ASSEMBLE SUPPORT FRAME FOR BENCH TOP—continued 13. Move to the lower strut connection and 14. Using a level, verify that the support leg is 15. Repeat to attach the remaining strut for the reposition band clamp as needed. plumb/vertical.
- Page 10 Assembly Instructions • (3) 1.25" x 1.25" square tubes (See Quick Start section for ID.) INSTALL LONG BENCH TOP SUPPORT TUBES • 112431 aluminum angle clips (Bench length determines quantity.) Actual length may differ. Measure and adjust as needed. 1. Set one long 1.25" x 1.25" square tube on the 2.
- Page 11 Assembly Instructions INSTALL LONG BENCH TOP SUPPORT TUBES—CONTINUED 7. Take another Tek screw and secure the clip 8. Remove the clamp and move to the opposite 9. Next, move to the mid support assembly and end of the frame and repeat the steps to install install a clip at that location.
- Page 12 Assembly Instructions INSTALL LONG BENCH TOP SUPPORT TUBES—CONTINUED 13. Measure to center tube end-to-end. 14. At one end, align the center of the tube with 15. Install angle clip and Tek screws to secure the the center mark made in Step 11 and clamp tube to the crossbar.
- Page 13 Assembly Instructions ASSEMBLE BENCH TOP For best results, assemble the bench top frame with an assistant on a flat, level surface. Gather the parts for the support frame: • (2) 112399L072375 frame end rails–short • 125P072G14 bench top supports • FA4482B Tek screws •...
- Page 14 Assembly Instructions ASSEMBLE BENCH TOP—continued 7. Move to the end rails and attach side rails as 8. With assistance, gently tap the rails to seat 9. Using a carpenter's square, square all corners. shown. Position the channel edges of the side the ends at the corner.
- Page 15 Assembly Instructions 102921B FA4482B ASSEMBLE BENCH TOP—continued Neo-Bonded Tek Screw Washer ATTENTION: Actual bench may differ from what is shown. Consult the Quick Start Guide for your bench details. 12. With assistance, carefully lift the expanded 13. Lower the expanded metal top into the frame. NOTE: Use a block of wood or small hammer metal top and carry it to the assembled frame.
- Page 16 Assembly Instructions 102921B FA4482B ASSEMBLE BENCH TOP—continued Neo-Bonded Tek Screw Washer 17. Continue to install Tek screws and washers NOTE: Install screws in a position that best Photo shows a Tek screw and washer installed along the side rail at each support tube. secures both the expanded metal top and the through the side rail and into the support tube.
- Page 17 Assembly Instructions ATTENTION: Actual bench may differ from what is shown. SECURE TOP TO THE MAIN SUPPORT FRAME Consult the Quick Start Guide for your bench details. 1. Square the bench top on the support frame. 2. Move to a bench top support closest to the 3.
- Page 18 Quick Start Guide 6' x 8' Premium Bench – Stationary Top 112416S6X08 6' x 10' Premium Bench – Stationary Top 112416S6X10 6' x 12' Premium Bench – Stationary Top 112416S6X12 WARNING: Evenly distribute weight when using bench. Never stand on bench top or allow anyone to stand on bench.
- Page 19 6' x 8' (112416S6X08) Premium Bench – Stationary Top See next page for 6' x 8' bench top parts. FALB10B FAG102B Bolt 112391 Bolt Clamp S125P096G14 FA4482B Tek Screw S125P057G14 QH1070 Pipe Strap S125P096G14 112431 Angle Clip 112391 131P072 Bolt Clamp S125P03175 QH1070 Pipe Strap...
- Page 20 6' x 8' (112416S6X08) Bench Top – Exploded View FA4482B 108553 Wafer 102921B Tek Screw Head Screw Neo-Bonded Washer 6' x 8' Bench Top 112416S6X08 FA4482B Tek Screw and 102921B Neo- Bonded Washer S125P072G14 Support Tube 112815 Poly Bench Corner 108553 Waferhead Screw...
- Page 21 6' x 8' (112416S6X08) Bench Top – Installation 112431 Angle Clips Secure the bench top to the support tubes of the main frame using Tek screws and 112431 angle clips. See Procedure 6. Install one 112431 clip at each corner of the bench top.
- Page 22 PAGE RESERVED FOR CUSTOMER NOTES AND RECORDS Revision date: 08.26.15...
- Page 23 6' x 10' (112416S6X10) Premium Bench – Stationary Top See next page for 6' x 10' bench top parts. FALB10B FAG102B Bolt S125P120G14 112391 Bolt Clamp S125P057G14 FA4482B Tek Screw 112431 QH1070 Pipe Strap Angle Clip 131P096 112391 Bolt Clamp S125P120G14 S125P03175 QH1070...
- Page 24 6' x 10' (112416S6X10) Bench Top – Exploded View FA4482B 108553 Wafer 102921B Tek Screw Head Screw Neo-Bonded Washer 6' x 10' Bench Top 112416S6X10 FA4482B Tek Screw and 102921B Neo-Bonded Washer S125P072G14 Support Tube 112815 Poly Bench Corner 108553 Waferhead Screw ATTENTION: Evenly space the S125P072G14...
- Page 25 6' x 10' (112416S6X10) Bench Top – Installation 112431 Angle Clips Secure the bench top to the support tubes of the main frame using Tek screws and 112431 angle clips. See Procedure 6. Install one 112431 clip at each corner of ST01500D706G19 the bench top.
- Page 26 PAGE RESERVED FOR CUSTOMER NOTES AND RECORDS Revision date: 08.26.15...
- Page 27 6' x 12' (112416S6X12) Premium Bench – Stationary Top See next page for 6' x 12' bench top parts. FALB10B FAG102B Bolt 112391 Bolt Clamp S125P144 S125P057G14 FA4482B Tek Screw QH1070 Pipe Strap 131P120G17 S125P144 112391 112431 Bolt Clamp Angle Clip S125P03175 QH1070 Pipe Strap...
- Page 28 6' x 12' (112416S6X12) Bench Top – Exploded View FA4482B 108553 Wafer 102921B Tek Screw Head Screw Neo-Bonded Washer 6' x 12' Bench Top 112416S6X12 FA4482B Tek Screw and 102921B Neo-Bonded Washer S125P072G14 Support Tube 112815 Poly Bench Corner 108553 Waferhead ATTENTION: Evenly space the S125P072G14 Screw...
- Page 29 6' x 12' (112416S6X12) Bench Top – Installation 112431 Angle Clips Secure the bench top to the ST01500D706G19 support tubes of the main frame using Tek screws and 112431 angle clips. See Procedure 6. Install one 112431 clip at each corner of the bench top.