Page 2
Important Information READ THIS DOCUMENT BEFORE YOU BEGIN Thank you for purchasing this premium greenhouse bench. When properly assembled and maintained, this product will provide years of reliable service. These instructions include helpful hints and important information needed to safely assemble and properly maintain the bench. Please read these instructions before you begin.
Page 3
Important Information PICTORIAL GUIDE The following graphics and photos will help identify the different parts of your bench. (Some parts may not be shown.) 102921B FALB10B FAG102B FA4482B 108553 Wafer Neo-Bonded 1/4" Nut 1/4" x 3/4" Bolt Tek Screw Head Screw Washer 112399Lxxxxxx 112815 Poly Corners...
Page 4
Assembly Instructions FRAME ASSEMBLY (CONTINUED) FA4482B Tek Screw FALB10B FAG102B FA4482B FALB10B FAG102B QH1070 Pipe Bolt Tek Screw 1/4" Nut 1/4" x 3/4" Bolt QH1070 Strap 112391 Pipe Strap Bolt Clamp 112675 End Plug S125P060 S125P0xxG14 (Length depends on bench.) S125P033 Install one 112675 end plug in each end of each long support tube and back support tubes.
Assembly Instructions FRAME ASSEMBLY Use the photos and information on the following pages to construct the bench frame. FA4482B Tek Screw NOTE: The 12' bench has four (4) support assemblies. The 8' and 10' benches each have three (3) supports. ST01500D706G19 Strut Revision date: 02.17.23...
Page 6
Assembly Instructions LOWER TIER BENCH ASSEMBLY For best results, assemble the bench top frame with an assistant on a flat, level surface. Gather the parts for the support frame: • (2) 112399L036375 frame end rails–short • 125P048 bench top supports •...
Page 7
Assembly Instructions LOWER TIER BENCH ASSEMBLY (CONTINUED) 7. Move to the end rails and attach side rails as 8. With assistance, gently tap rails to seat the 9. Using a carpenter's square, square all corners. shown. Position channel edges of side rail on ends at the corner.
Page 8
Assembly Instructions 102921B FA4482B LOWER TIER BENCH ASSEMBLY (CONTINUED) Neo-Bonded Tek Screw Washer 12. With assistance, carefully lift the expanded 13. Lower expanded metal top into frame. Gently NOTE: Use a block of wood or small hammer metal top and carry it to the assembled frame. tap frame rails as needed to allow top to drop if needed to lightly tap frame rails apart to CAUTION: Metal is sharp! Wear gloves to...
Page 9
Assembly Instructions 102921B FA4482B LOWER TIER BENCH ASSEMBLY (CONTINUED) Neo-Bonded Tek Screw Washer 17. Continue to install Tek screws and washers NOTE: Install screws in a position that best Photo shows a Tek screw and washer installed along side rail at each support tube. secures both the expanded metal top and through side rail and into support tube.
Page 10
Assembly Instructions LOWER TIER BENCH ASSEMBLY (CONTINUED) FA4482B 108553 Wafer 102921B Tek Screw Head Screw Neo-Bonded Washer FA4482B Tek Screw and 102921B Neo- Bonded Washer S125P036 Support Tube 112815 Poly Bench Corner* 108553 Waferhead Screw ATTENTION: Evenly space the S125P048 support tubes during assembly.
Page 11
Assembly Instructions ATTACH LOWER TIER BENCH Square the bench top on the support frame. Verify that each side is equal distance from the 1.25" x 1.25" support tube. Ends of top will rest on the ends of all long support tubes. FA4482B Tek Screw Diagram above shows the 112431 clip connections.
Page 12
Assembly Instructions TOP TIER BENCH ASSEMBLY FA4482B 108553 Wafer 102921B Tek Screw Head Screw Neo-Bonded Washer S125P024 Support Tube FA4482B Tek Screw and 102921B Neo- Bonded Washer 112815 Poly Bench Corner* 108553 Waferhead Screw ATTENTION: Evenly space the S125P024 support tubes during assembly. Install one * Install Poly corners when bench support tube in the channel of each end rail.
Page 14
Assembly Instructions TOP TIER BENCH ASSEMBLY (CONTINUED) 112675 Tier height is adjustable. Varies from 10"-20" depending on strut placement and desired height. Install one 112675 end plug in each end of each long support tube and back support tubes. 15-3/4" END VIEW *Actual bench may differ from example shown.
Page 15
Assembly Instructions TOP TIER BENCH ASSEMBLY (CONTINUED) S125PxxxG14 (Length depends on bench.) FA4482B Tek Screw Diagram above shows the 112431 clip connections. 112431 Angle Clip Square the bench top on the support frame. Verify that each side is equal distance from the 1.25" x 1.25"...
Page 16
Assembly Instructions 3' x 8' Premium Stationary Multi-Level Bench 112413S3X08T22 3' x 10' Premium Stationary Multi-Level Bench 112413S3X10T22 WARNING: Evenly distribute weight when using bench. Never stand or allow anyone to stand on bench. 3' x 12' Premium Stationary Multi-Level Bench 112413S3X12T22 *Actual bench may differ from example shown.
Page 17
Notes age is reserved for customer's notes. Revision date: 02.17.23...