Kasco 3400JF Owner's Manual page 15

C85 / C95 non-metallic Control Panel
TIME CLOCK SETTING
To set the current time, turn the inner dial clockwise.
Do not set the time by rotating "outer" dial.
Turn the minute hand or small plastic inner dial clock-
wise until the time of day on the outer dial is aligned
with the triangle marker on the inner dial (two o'clock
position).
Example for 10:00 AM. Turn the minute hand clock-
wise until 10:00 AM is aligned with the triangle on
the inner dial. The hour and the minute dial will show
exactly 10:00.
Captive trippers
Triangle marker (in the on position)
Dimensions
FM/1 synchronous/quartz
TIME SETTING
TO SET THE CURRENT TIME (AND DAY OF WEEK
ON 7 DAY UNITS), TURN THE MINUTE HAND
CLOCKWISE. DO NOT SET THE TIME BY ROTAT-
ING "OUTER" DIAL.
Turn the minute hand clockwise until the day of the week
(7-day timer) and the time of day on the outer dial is
aligned with the triangle marker on the inner dial (two
o'clock position).
Example for 7-day program dial Monday 10:30 AM. Turn the
PROGRAMMING
minute hand clockwise until Monday 10:30 AM is aligned
The 24-Hour dial has quarter-hour divisions and AM/
with the triangle on the inner dial. The hour and minute hand
PM indications.
will show exactly 10:30.
The time switch is programmed by pushing the captive
Example for 24-hour program dial 10:30 AM. Turn the minute
trippers to the outer ring position for the entire pe-
hand clockwise until 10:30 AM is aligned with the triangle on
the inner dial. The hour and the minute dial will show exact-
riod that the aerator is to be turned "ON", i.e., fifteen
ly 10:30.
PROGRAMMING
7-Day (SW, QRW Models)
Timer
minutes for each tripper on the 24-Hour dial. When
the tripper is pushed to the inside, the switch is in the
"OFF" position.
PROGRAMMING WITH MANUAL OVERRIDE
SWITCH
Your Timer may have a 3-way manual switch or a
2-way manual switch.
AUTOMATIC MODE
In order to operate the time clock in the automatic
mode, the manual switch must be in the automatic
postion- see diagram.
MANUAL MODE
For the 3-way switch, with the manual override switch
in the lower position, marked "O", the time clock
output will remain Permanently OFF. In the upper
position, marked "I", the time clock output will remain
permanently ON.
PROGRAMMING WITH MANUAL
For the 2-way switch, with the manual override switch
OVERRIDE SWITCH
in the lower position, marked "ON" the time clock
AUTOMATIC MODE
output will remain permanently ON.
In order to operate the time switch module in the automatic
mode, the manual switch must be in the center position (auto-
matic) - see diagram.
MANUAL MODE
With the manual switch selector lever the selected programs
can be overridden. In the lower position, marked "O", termi-
nals 3 and 5 are permanently closed. In the upper position,
marked "I", terminals 3 and 4 are permanently closed (see
SETTING THE TIMER
The timer is a 24 hour time clock with 15 minute increment settings.
diagram).
The captive trippers change the SPDT relay state when pushed
toward the outside.
1. Setting time of day
(a) Synchronize the timer by aligning arrow at the 2:00 position
of inner face with the corresponding time of day printed on the
outer ring.
Override Mode
NOTE: Power must be ON to keep time synchronization.
2. Setting ON time and duration
Locate desired activation time(s) on outer ring (b) and push
trippers to the outside (c). Each tripper represents 15 minutes
activation time. Push as many trippers back as desired for dura-
tion time. When the timer reaches the fi rst tripper, the timer SPDT
3-way manual
contacts will change state and turn ON. It will remain ON for as
long as the following trippers are pushed out. When timer goes
override switch
past last tripper, the timer will return to the OFF mode. The timer
has a selector for (d) AUTOMATIC and ON modes.
TIME SETTING
TO SET THE CURRENT TIME (AND DAY OF WEE
ON 7 DAY UNITS), TURN THE MINUTE HAN
CLOCKWISE. DO NOT SET THE TIME BY ROTAT
ING "OUTER" DIAL.
Turn the minute hand clockwise until the day of the wee
(7-day timer) and the time of day on the outer dial
aligned with the triangle marker on the inner dial (tw
o'clock position).
Example for 7-day program dial Monday 10:30 AM. Turn th
minute hand clockwise until Monday 10:30 AM is aligne
Overide Mode
with the triangle on the inner dial. The hour and minute han
2-way manual
will show exactly 10:30.
overide switch
Example for 24-hour program dial 10:30 AM. Turn the minu
hand clockwise until 10:30 AM is aligned with the triangle o
the inner dial. The hour and the minute dial will show exac
ly 10:30.
PROGRAMMING
Dimensions
FM/1 synchronous/quartz
I = permanent ON
= automatic
0 = permanent OFF
ON - Permanently ON
AUTO - automatic
15