Page 1
J Series Fountain 3400JF, 3400HJF, 4400JF, 4400HJF Operation & Maintenance Manual 800 Deere Rd. Prescott, WI 54021 • 715.262.4488 • sales@kascomarine.com • www.kascomarine.com Document number 884180...
Page 2
The water is pulled upward and thrust through the flotation collar into the air. Your Kasco Marine fountain is ready for immediate use (after installation)� The motor and ball bearings are submerged in oil, and no further lubrication is needed�...
Page 3
3400 - 4400 J-SERIES FOUNTAIN MANUAL IMPORTANT SAFETY • Please read and follow these important instructions to help ensure your safety and the quality performance of your Kasco equip- ment� • Use caution when dealing with any electrical and/or moving equipment�...
Page 4
Back to Contents 3400 - 4400 J-SERIES FOUNTAIN MANUAL PARTS INCLUDED Description Part # Fountain Float 242001 1/4-20 x 4” Phillips Pan Head Screw 251220 1/4” split washers 840537 1/4” (3/4” OD) Flat Washer 251300 1/4 -20 x 1-3/4” Hex Head Bolt 475630 Bottom Screen Section 361540...
Page 5
Back to Contents 3400 - 4400 J-SERIES FOUNTAIN MANUAL ASSEMBLY INSTRUCTIONS 1. Rest the float on the 4 legs of the housing Align power cord with notch Align bolt holes with legs� 2� Lock washer goes between bolt and flat washer. Tighten down in 4 places.
Page 6
If your Kasco cord comes with a strain relief kit attached, attach the available link to the float-side knot in the mooring rope, as pictured here�...
Page 7
Back to Contents 3400 - 4400 J-SERIES FOUNTAIN MANUAL INCLUDED NOZZLES Pattern Description Model Height Width Included in Kit 3400 13’ 8’ Narrow geyser, marked S� (Pre-installed) 431230 Sequoia 4400 18’ 11’ 3400 9’ 29’ Center geyser with lower conical pattern, 431232 Linden 2-piece assembly with bolt�...
Page 8
High water level After unit is installed in the water, connect the power cord to a properly installed Kasco control panel (C-85, C-95, etc.) with built-in ground fault protection according to the instructions and electrical schematics included with the panel� Follow all local and national electrical codes for unit and control panel installation;...
Page 9
Seal replacement and all other repair services should be performed by Kasco Marine or a Kasco-trained Authorized Repair Center� Any alterations or changes made to Kasco units by an unauthorized source will void the warranty� This includes tampering with the unit, power cord, and/or control panel.
Page 10
Kasco® Marine, Inc� warrants this fountain to be free from defects in material or workmanship under normal use and service (exclud- ing ropes, power cord, and propeller)� The Kasco Marine, Inc� obligation under this warranty is limited to replacing or repairing free of charge any defective part within the warranty period from the date of shipment�...
Page 11
• Kasco Marine does estimates on repairs at the request of the customer� The request for estimate should be included in the letter that accompanies the returned unit and must include a daytime phone number and/or e-mail address� We will contact the customer with a total after the unit has been evaluated, but before the work is performed�...
Page 12
“My fountain turns itself off and back on without the timer and without tripping the GFI breaker.” (single phase units only) Each Kasco fountain has a Thermal Overload built in that will turn the unit off when it overheats� Once the unit has cooled down, it will start back up�...
Page 13
Back to Contents 3400 - 4400 J-SERIES FOUNTAIN MANUAL REPLACEMENT PARTS Description Qty Part # Zinc assembly 243475 Debris flinger, .500 dia. shaft 990410 Baseplate 431100 O-ring, for base 431246 Retaining clip 140313 1/4”-20 x 1-3/4” bolt 475630 Nut, 1/4”-20 serrated flange 840538 1/2”-20 jam nut 342058...
Page 14
3400 - 4400 J-SERIES FOUNTAIN MANUAL REPAIR CONTACT FORM • Kasco requires that all equipment sent for repair MUST be accompanied by this form and marked to Repairs attention� • Kasco is NOT responsible for shipping damage accrued in return shipment� •...