Table of Contents
Advertisement
7. "Close lid and insert carafe. Press OK to start": close the lid
and attach the carafe to the connection nozzles (A11) (fig.
34): the appliance beeps (if the beep function is enabled);
8. Press "OK" to start mixing. The appliance proceeds with
preparation and the image of the beverage appears on the
control panel, together with a progress bar which gradual-
ly fills as the operation proceeds and a description of the
phase (mixing).
9. Preparation stops automatically and the message "Your
beverage is ready!" appears on the display. The cold milk
is ready to be poured into the cup. Use all the beverage
prepared; if any is left, do not put back in the refrigerator.
Please note!
•
To interrupt preparation at any moment, press "Stop".
12. TEA FUNCTION
Important! Danger of scalding.
Do not leave the appliance unattended while hot water is being
delivered.
To make tea, proceed as follows:
4. "BEVERAGE SETTINGS": the parameters that can be cus-
tomised according to your tastes appear on the display:
"Quantity"
"Temperature"
A different tea (white, green, oolong
or black) appears with each water
temperature
5. Press "OK" to start making the tea. The appliance proceeds
with preparation and the image of the beverage appears
on the control panel, together with a progress bar which
gradually fills as the operation proceeds and a description
of the phase (water delivery). The message "Your beverage
is ready!" appears on the display;
1. Make sure the hot water/
steam spout (F) is at-
tached correctly to the
connection nozzles (A11);
2. Put a tea bag in the cup,
then place the cup under
the spout (as close as pos-
sible to avoid splashes)
(fig. 40);
3. To make the beverage,
press the image on the
40
homepage corresponding
to the tea function;
6. The machine delivers the chosen quantity of hot water,
then delivery stops automatically.
Please note!
•
If "Energy Saving" mode is active, you may have to wait a
few seconds before the hot water is delivered.
•
To stop delivery manually, press "Stop".
•
As soon as delivery has ended, to increase the quantity
of water in the cup, just press "Extra". When the required
quantity is reached, press "Stop".
13. DELIVERING HOT WATER
To deliver hot water, proceed as follows:
1. Attach the hot water/steam spout (F) to the connection
nozzles (A11) (fig. 7): the appliance beeps (if the beep
function is enabled);
2. Place a cup under the spout (as close as possible to avoid
splashes) (fig. 40).
3. Select the function as described in the following
paragraphs.
13.1 Your beverage at a touch
Press the image on the homepage corresponding to hot water.
The appliance proceeds with preparation and the image of the
beverage appears on the display together with a progress bar
which gradually fills as the operation proceeds and a description
of the phase (water delivery).
At the end of preparation, the message "Your beverage is
ready!" appears on the display. The appliance is now ready to
be used again.
Please note!
As soon as delivery has ended, to increase the quantity of water
in the cup, just press "Extra". When the required quantity is
reached, press "Stop".
13.2 Customising the beverages
To deliver the desired quantity of hot water, proceed as follows:
1. Press
at the bottom of the image corresponding to hot
water. The selectable quantities appear on the display (B1):
"Quantity"
2. After selecting the quantity, press
proceeds with preparation and the image of the beverage
appears on the display together with a progress bar which
gradually fills as the operation proceeds and a description
of the phase (water delivery).
3. At the end of delivery, the message: "Your beverage is
ready! Save new settings?" is displayed;
4. Press "Save" to save the settings (or "Cancel" to retain the
previous parameters).
17
2X
1X
: The appliance
Advertisement
Table of Contents
Troubleshooting
