Table of Contents
Advertisement
GE H
EALTHCARE
D
5141177-100, R
IRECTION
EVISION
Chapter 6
Floor Loading and Weights
Section 1.0
Floor Loading
The BrightSpeed system has a total floor load of approximately 2880 kg (6340 lbs). About 2310 kg
(5088 lbs), including patient (205 kg (450 lbs)), is concentrated in the table-gantry assembly.
Table 6-1
ITEM
NET WEIGHT
LB(KG)
Gantry (w/
~3899
covers)
(~1770)
Dollies (each)
250 (114)
Top Cover (each)
15.4 (7)
Side Cover (each)
11 (5)
Front Cover
92.5 (42)
Rear Cover
92.5 (42)
Patient Table
1201 (545)
Includes 450
(205) Patient
Dolly
215 (98)
Patient Table:GT
980 (445) /
1700V w/227kg
1481 (672)
patient
Foot Switch
73 (33)
Power Distribution
~770
Unit
(~350)
Console w/
Elite:
single-piece
430 (195)
desktop & w/o
Edge/Excel:
monitors
397 (180)
Notes:
1.) Use the GE Supplied mounting hardware ONLY IF APPROVED by qualified personnel.
[See statements in
8.1 -
2.) Seismic angle brackets are included and shipped with the PDU..
Table 6-1 BrightSpeed System Floor Loading
14
lists CT components with weight, size, floor loading and normal mounting requirements.
OVERALL
WEIGHT/AREA
W X D
LB/SQ. FT.
INCH (MM)
(KG/M
81 x 40.1
263 (1286)
(2057 x 1018)
24.3 x 94
175 (852)
(616 x 2387)
25.6 x 93.3
493 (2408)
(650 x 2370)
-
-
28 x 22
185 (909)
(700 x 550)
48.8 x 48.6
Eilte: 140 (681)
(1240 x 1235)
Edge/Excel:
134 (652)
Table and Gantry Mounting Requirements, on
Chapter 6 - Floor Loading and Weights
B
S
RIGHT
LOAD PATTERN
IN. (MM)
2
)
Rectangular base plate 27.6
X 77.4 (700 X 1966) with four
round pads, each 2.5 (63.5)
in contact with floor.
Individual pad loadings are:
910 lb, 960 lb, 1040 lb, and
1090 lb (see
Figure
).
Rectangular base 17 X 57.5
(432 X 1460) with five round
pads, each 2.5 (63.5) in
contact with floor. Worst-
case cantilever pull on any
bolt is 1235 lb (561 kg).
For round 63.5mm pads.
Max Anchor Load is 1363lbs
(6061N).
-
Four Casters support area of
28 X 22 (711 X 559).
Four Casters or Leveling
Feet support area of 46 X 19
(1168 X 483).
page
84.]
E
, E
, E
: P
-I
PEED
LITE
DGE
XCEL
RE
NORMAL METHOD OF
MOUNTING IN. (MM)
(GE SUPPLIED)
Hilti Kwik-Bolt II 1/2in (12.7mm)
diameter by 8in (203mm) long per P/N
2106573 at four leveling pads into
concrete floor.
Hilti Kwik-Bolt II 1/2in (12.7mm)
diameter by 8in (203mm) long per P/N
2106573 at three leveling pads into
concrete floor.
Hilti Kwik-Bolt II 1/2in (12.7 mm)
diameter by 8in (203mm) long per P/N
2106573 at the leveling pads into
concrete floor.
-
Casters are for positioning and service.
Set on floor. May be anchored to floor
2
using angle brackets
in seismic
zones.
Casters are for positioning. Set on
floor. Console may be anchored to
floor using angle brackets
NSTALLATION
1
2
Page 103
Advertisement
Table of Contents
