Honda Hawk GT NT650 1988 Service Manual page 9

GENERAL INFORMATION
TORQUE VALUES
The torque specifications listed under "Engine" and "Frame" are for specific tightening points. If a specification is not listed,
follow the standard torque values below.
STANDARD TORQUE VALUES
TYPE
TORQUE N'm (kg-m, ft-Ib) TYPE TORQUE N'm (kg-m, ft-Ib)
5 mm bolt, nut 5 (0.50, 3.6)
5 mm screw
4 (0.40, 2.9)
6 mm bolt, nut 10 (1.0, 7.2)
6 mm screw, 6 mm
8 mm bolt, nut
22 (2.2, 16)
bolt with 8 mm head
9 (0.9, 6.5)
10 mm bolt, nut 35 (3.5, 25)
6 mm flange bolt, nut
12 (1.2,"9)
12 mm bolt, nut 55 (5.5,40) 8 mm flange bolt, nut 27 (2.7, 20)
10 mm flange bolt, nut
40 (4.0,29)
ENGINE
Item Q'ty
Thread dia.
Torque
Remark
(mm)
N'm (kg-m, ft-Ib)
Spark plug
4 12 14(1.4,10)
Cylinder head cover bolt 4 6 10 (1.0, 7.2) Special bolt
Camshaft holder bolt 6 8 23 (2.3, 17)
nut
2 8
23 (2.3, 17)
6 mm bolt 4
6
10(1.0,7.2)
Cylinder head nut
8 10
48 (4.8, 35)
bolt
4 8
23 (2.3, 17)
8 mm nut 4
8
23 (2.3, 17)
6 mm bolt 2 6 10(1.0,7.2) Socket bolt
Camshaft sprocket bolt 4
7
23 (2.3, 17)
NOTE 1
Clutch lock nut
1 18 130 (13.0, 94) Staked nut.
Right crankcase cover bolt
15 6
10(1.0,7.2)
Left crankcase cover bolt
9 6
10(1.0,7.2)
Oil filter cartridge 1 20 10(1.0,7.2) Apply clean engine oil to the
.
O-ring
Oil drain bolt
1 14 35 (3.5, 25)
Neutral switch
1 10 12(1.2,9)
Oil pressure switch 1
- -
12 (1.2, 9)
NOTE 4
Primary drive gear bolt
1 12 90 (9.0, 65) UBS bolt, NOTE 2
Flywheel bolt
1 12
130 (13.0, 94)
Left hand threads, NOTE 2
Starter one way clutch
6 8
30 (3.0,22)
Torx bolt, NOTE 1
Oil control bolt
1 10 23 (2.3, 17)
Oil pipe bolt
2 7
10(1.0,7.2)
Special bolt
Connecting rod cap nut
4
8
34 (3.4,25)
Crankcase bolt
14 8 27 (2.7, 20) NOTE 2
6 6
12 (1.2, 9)
NOTE 2
Shift drum stopper plate bolt
1 6
26 (2.6, 19)
NOTE 1
Insulator band screw
4 5 4 (0.4,2.9)
NOTE 2
Timing hole cap
1 14 10 (1.0, 7.2) NOTE 3
Crankshaft hole cap 14
30
15(1.5,11)
NOTE 3
Oil pump driven sprocket bolt
1 6 15(1.5,11) NOTE 1
Valve adjusting screw lock nut
6 7 23 (2.3, 17)
Cylinder stud bolt 8mm 2
8
20-30 (2.0-3.0,
NOTE 1, Refer section 10.
14-22)
10 mm
8 10 30- 50 (3.0- 5.0, NOTE 1, Refer section 10.
22-36)
.
NOTE 1: Apply a locking agent to the threads.
NOTE 2: Apply clean engine oil to the threads.
NOTE 3: Apply molybdenum disulfide grease to the threads.
NOTE 4: Apply sealant to the threads.
1-5