CMOS Setup / Boot Procedure
•
Turn power on.
•
Press the DEL key the instant that video is displayed (during the memory test).
•
Verify default CMOS Setup information as shown below.
•
Insert bootable floppy disk into floppy drive.
•
Reset computer using push button reset.
•
See VersaLogic KnowledgeBase article
more information about these parameters.
+------------------------------------------------------------------------------+
|
|
+---------------------------+--------------------+-----------------------------+
| DRIVE ASSIGNMENT ORDER:
| Drive A: Floppy 0
| Drive B: (None)
| Drive C: IDE 0/Pri Master +--------------------+ Show "Hit Del"
| Drive D: (None)
| Drive E: (None)
| Drive F: (None)
| Drive G: (None)
| Drive H: (None)
| Drive I: (None)
| Drive J: (None)
| Drive K: (None)
| (Loader): (Unused)
+---------------------------+ Ide 0: 3 = AUTOCONFIG, LBA
| FLOPPY DRIVE TYPES:
| Floppy 0: 1.44 MB, 3.5"
| Floppy 1: Not installed
+---------------------------+--------------------------------------+-----------
+------------------------------------------------------------------------------+
|
|
+---------------------------------------+--------------------------------------+
| D0000h 64k page function
| PLD register base I/O
| Force Ethernet 10-BaseT
| PS/2 Mouse (IRQ12)
| LPT1 (378h)
| Parallel Port Mode
| CPU Speed
| Cache Mode
| Write Buffer
| GP Bus Timings
| Console Redirection
+---------------------------------------+--------------------------------------+
Note:
Due to changes and improvements in the system BIOS, the information on your
monitor may differ from that shown above.
EPM-4 Reference Manual
Basic CMOS Configuration
System Bios Setup - Basic CMOS Configuration
(C) 2002 General Software, Inc. All rights reserved
| Date:>JAN 1, 1980
| Time: 00 : 00 : 00 | Typematic Rate
| NumLock: Disabled
| BOOT ORDER:
| Boot 1st: Drive A: | F1 Error Wait
| Boot 2nd: Drive C: | Parity Checking
| Boot 3rd: (None)
| Boot 4th: (None)
| Boot 5th: (None)
| Boot 6th: (None)
+--------------------+-----------------+-----------+
| ATA DRV ASSIGNMENT:
| Ide 1: 3 = AUTOCONFIG, LBA
| Ide 2: Not installed
| Ide 3: Not installed
Custom Configuration
System BIOS Setup - Custom Configuration
(C) 2002 General Software, Inc. All rights reserved
: ISA bus
: 0E0h
: Disabled
: Enabled
: Disabled
: FDD
: 133 MHz
: Wr-back
: Enabled
: Normal
: Auto
CMOS Setup / Boot Procedure
VT1476 – EPM-4 CMOS Setup Reference
| Typematic Delay
| Seek at Boot
| Config Box
| Memory Test Tick : Enabled
| Debug Breakpoints: (Unused) |
| Debugger Hex Case: Upper
| Memory Test : StdLo FastHi
Sect
Hds
| COM1 (3F8h) RS-232
| COM2 (2F8h) RS-232
| COM3 (3E8h) RS-422/485
| COM4 (2E8h) RS-422/485
| GP Timer 0
| GP Timer 1
| Watchdog Timer
| PCI Int A
| PCI Int B
| PCI Int C (Ethernet)
| PCI Int D
Configuration / Operation – 9
for
|
|
: 250 ms
|
: 30 cps
|
: None
|
: Enabled
|
: Enabled
|
: Enabled
|
: (Unused) |
|
|
|
Cyls | Memory
|
|
Base:
|
|
633KB
|
|
Ext:
|
|
63MB
|
+
|
|
: IRQ4
|
: IRQ3
|
: Disabled |
: Disabled |
: Disabled |
: Disabled |
: Disabled |
: IRQ11
|
: IRQ11
|
: IRQ11
|
: IRQ11
|