Android Support - DFI FS053 User Manual

Android Support

(*) is depended on the NXP support.
Component Support Status
5.1.1
Android Version
3.14.52
Kernel Version
Support eMMC boot, eMMC v5.1, Linux ext4 file system
eMMC
1. Support "ping", "ifconfig" console commands, and NXP Ethernet APP (*)
2. Support static IP/DHCP Dynamic IP, fixed MAC address
3. If both LAN1 Ethernet port and LAN2 Ethernet port are plugged-in with
Ethernet cables, only the first Ethernet port plugged-in with Ethernet
Ethernet LAN1
cable will connect to network. If the first Ethernet port plugged-in with
Ethernet cable is unplugged, the second Ethernet port will connect to
network automatically.
1. Support "ping", "ifconfig" console commands, and NXP Ethernet APP (*)
2. Support static IP/DHCP Dynamic IP, fixed MAC address
3. If both LAN1 Ethernet port and LAN2 Ethernet port are plugged-in with
Ethernet cables, only the first Ethernet port plugged-in with Ethernet
Ethernet LAN2
cable will connect to network. If the first Ethernet port plugged-in with
Ethernet cable is unplugged, the second Ethernet port will connect to
network automatically.
1. Support USB HID Keyboard and Mouse Device
2. Support Android auto mount USB Mass Storage function (only one USB
storage is available at a time. If second USB is plugged-in the USB cable,
USB 2.0
second USB is not available. If first USB is unplugged, second USB needs
to be unplugged and re-plugged back to be available.) FAT32 filesystem
only without multi-partition
1. Support USB HID Keyboard and Mouse Device
2. Support Android auto mount USB Mass Storage function (only one USB
storage is available at a time. If second USB is plugged-in the USB cable,
second USB is not available. If first USB is unplugged, second USB needs
USB OTG
to be unplugged and re-plugged back to be available.) FAT32 filesystem
only without multi-partition
3. Support connect to PC to update image by i.MX6 MFGTool
1. Support LVDS+HDMI dual display — LVDS as main output — resolution
800x480, RGB666 (Rev. B default, verified panel: AM-800480R3TMQW-
T31H)
LVDS Panel
2. For Android standard product, dual display is by default enabled.
3. Multi-panel selection function for backward compatibility (activation
required, please refer to Appendix A).
Chapter 3 Software User Guide
Chapter 3
1. Support Android->Settings->Display->Brightness level control without
adaptive brightness function.
LVDS Backlight
2. For standard product, we do not port any light sensor module.
Support single touch function
Touch
1. Default support LVDS+HDMI dual display function. HDMI is slave
output, resolution 1024x600 (based on LVDS resolution).
2. If users want to change HDMI resolution (i.e. 1920x1080), users need
HDMI Video
to modify kernel parameter to change LVDS resolution to 1920x1080 too.
Output
3. For Android standard product, we enable dual display function by
default.
1. Support read input voltage, set outpout voltage high/low status, control
by Linux device node, 8 pins
DIO
2. Support DFI Android GPIO demo APP (support by request)
1. Support SD card boot, support SD storage by "mount" console
command, FAT32 filesystem. (Support Kingston, micro SDHC 4GB class 4,
4GB/16GB)
Micro SD Card
2. Support Android auto mount SD card function (FAT32 filesystem only,
(SD Slot)
without multi-partition)
3. For standard product, we do not port any SDIO module.
1. Support "busybox lspci" console command for check PCIe card status.
Mini PCIe
2. For standard product, we only port ENLi AP12356 WiFi/BT module.
1. Support SATA hard disk storage only
2. Support Android auto mount SATA function (FAT32 filesystem only,
SATA (Quad
without multi-partition)
Only)
3. For standard product, we do not port any SATA module.
Support Loopback & flow control test, BR 115200 by DFI Android UART
UART1 - RS232
demo APP (supoprt by request)
Support Loopback test, BR 115200 by DFI Android UART demo APP
UART1 - RS485
(supoprt by request)
Support Loopback test, BR 115200 by DFI Android UART demo APP
UART1 - RS422
(supoprt by request)
Support Loopback test, BR 115200 by DFI Android UART demo APP
UART2 - RS485
(supoprt by request)
Support SPI2 Nor-Flash boot (Uboot image only)
SPI2 Nor-Flash
Support Android->Settings->Date to set system time function.
RTC
Support read device temperature (degrees C) by Android CPU-Z APP
Thermal Sensor
installed by user
Suport read Linux kernel debug log by serial port, use PC serial terminal
Debug Serial
tool (ex. PuTTY), BR 115200
Port
28
www.dfi.com