Yocto Support - DFI FS053 User Manual

Yocto Support

(*) is depended on the NXP support.
Component Support Status
1.8
Yocto Version
3.14.52
Kernel Version
X11 without QT5 build
Window System
Support eMMC boot, eMMC v5.1, Linux ext3 file system
eMMC
Support "ping", "ifconfig" console commands verify, static IP/DHCP
Ethernet LAN1
Dynamic IP, fixed MAC address.
Support "ping", "ifconfig" console commands verify, static IP/DHCP
Dynamic IP, fixed MAC address. Due to LAN7500 is PCIe over USB2.0
Ethernet LAN2
Ethernet card, data transfer throughput limit is below 480Mbps (USB2.0
SPEC limitation).
1. Support USB HID Keyboard and Mouse Device
2. Support USB Mass Storage by "mount" console command, EXT3/EXT4/
USB 2.0
FAT filesystem
1. Support USB HID Keyboard and Mouse Device
2. Support USB Mass Storage by "mount" console command, EXT3/EXT4/
USB OTG
FAT filesystem
3. Support connect to PC to update image by i.MX6 MFGTool
1. Single display function
- resolution 800x480, RGB666 (Rev. B default, verified panel: AM-
800480R3TMQW-T31H)
- resolution 1024x600, RGB24 (Rev. A default, verified panel:
LVDS Panel
OT070UADDBT-00)
2. Multi-panel selection function for backward compatibility (Rev. B Image
only; activation required, please refer to Appendix A).
Support control by Linux device node, level value 0~7
LVDS Backlight
Support single touch function (Rev. B Image only)
Touch
Support single display function, need to plug in HDMI cable before power
HDMI Video
on, resolution 1920x1080@60
Output
Support read input voltage, set outpout voltage high/low status, control
DIO
by Linux device node, 8 pins
Support SD card boot, support SD storage by "mount" console command,
Micro SD Card
FAT filesystem. (Support Kingston, micro SDHC 4GB class 4, 4GB/16GB)
(SD Slot)
For standard product, we do not port any SDIO module.
Chapter 3 Software User Guide
Chapter 3
Support "lspci" console command for check PCIe card status. For
Mini PCIe
standard product, we only port ENLi AP12356 WiFi/BT module.
Support SATA storage only (by "mount" console command, EXT3/
SATA
EXT4/FAT filesystem). For standard product, we do not port any SATA
(Quad Only)
module.
Support Loopback & flow control test, BR 115200 (need DFI Linux user
UART1 - RS232
space utility)
Support Loopback test, BR 115200 (need DFI Linux user space utility)
UART1 - RS485
Support Loopback test, BR 115200 (need DFI Linux user space utility)
UART1 - RS422
Support Loopback test, BR 115200 (need DFI Linux user space utility)
UART2 - RS485
Support SPI2 Nor-Flash boot (Uboot image only)
SPI2 Nor-Flash
Support Linux "date -s" and "hwclock -w" console commands to set
RTC
system time
Support read device temperature (degrees C) by Linux device node
Thermal Sensor
Suport read Linux kernel debug log by serial port, use PC serial
Debug Serial Port
terminal tool (ex. PuTTY), BR 115200
Support play MPEG4 file (need DFI Linux user space utility).
Play Video
Support NXP utility "wdt_driver_test.out"(*) to test Watchdog reboot
Watchdog
function
VNC Server Support PC control via VNC, disabled by default (Rev. B Image only)
1. Support AP12356 Wifi/BT module
2. AP12356 WiFi: Support Wifi STA Mode (connect Wifi AP), Soft AP
Mode (enable DHCP/IPv4 routing); support commands — ifconfig,
Wifi/BT wpa_supplicant, wpa_cli, udhcpc, hostapd, iptables console, and
ping console (for verification).
3. AP12356 BT: Support files transfer protocol only (BT OBEX protocol);
support commands — obexd, obexctl, and obexpushd console.
1. u-boot.imx : around ~420 KB
2. zImage: around ~6MB
Image Size
3. rootfs.tar.bz2: around ~245MB (compressed), or around ~830MB
(uncompressed)
Free Storage Size Around ~5.3G free space (/dev/root)
27
www.dfi.com