Related Manuals for DFI Qseven FS700 Series
Summary of Contents for DFI Qseven FS700 Series
- Page 1 FS700 Series Qseven Board User’s Manual A28550547 Chapter 1 Introduction www.dfi .com...
-
Page 2: Copyright
Copyright FCC and DOC Statement on Class B This publication contains information that is protected by copyright. No part of it may be re- This equipment has been tested and found to comply with the limits for a Class B digital produced in any form or by any means or used to make any transformation/adaptation without device, pursuant to Part 15 of the FCC rules. -
Page 3: Table Of Contents
Table of Contents Copyright ......................2 Trademarks ......................2 FCC and DOC Statement on Class B ............. 2 About this Manual ..................4 Warranty ......................4 Static Electricity Precautions ..............4 Safety Measures ....................4 About the Package ..................5 Chapter 1 - Introduction ................ -
Page 4: About This Manual
About this Manual Static Electricity Precautions An electronic file of this manual is included in the CD. To view the user’s manual in the CD, in- It is quite easy to inadvertently damage your PC, system board, components or devices even sert the CD into a CD-ROM drive. -
Page 5: About The Package
About the Package The package contains the following items. If any of these items are missing or damaged, please contact your dealer or sales representative for assistance. • One FS700-M60 board • One Heat spreader (for temperature -40°C to 85°C only) •... -
Page 6: Chapter 1 - Introduction
Chapter 1 Chapter 1 - Introduction Specifications Processor • Freescale i.MX 6 series processors Power • Under 5W @ 5V - i.MX6Q: i.MX 6Quad, up to 1.0GHz, Four Cortex-A9 cores Consumption - i.MX6D: i.MX 6Dual, up to 1.0GHz, Two Cortex-A9 cores Temperature •... -
Page 7: Features
Important: FAN control The DFI FS700 Series Qseven module provides Gigabit Ethernet with one Atheros AR8033 Ethernet PHY. The maximum throughput that the Gigabit Ethernet performs is limited to 470Mbps (total for Tx and Rx) due to internal bus limitations based on Fre- escale’s Errata ERR004512. -
Page 8: Chapter 2 - Hardware Installation
Chapter 2 Chapter 2 - Hardware Installation Block Diagram Board Layout 24 bits LVDS 24 bits LVDS DDR3 24 bits LVDS 24 bits LVDS Backlight Backlight eMMC DDR3 DDR3 I C 2 micro SD HDMI HDMI Top View RGMII Sensor GLAN PHY Freescale i.MX6 Series... -
Page 9: Mechanical Diagram
Chapter 2 Mechanical Diagram Important: Electrostatic discharge (ESD) can damage your processor, disk drive and other com- ponents. Perform the upgrade instruction procedures described at an ESD worksta- tion only. If such a station is not available, you can provide some ESD protection by FS700 Series Module wearing an antistatic wrist strap and attaching it to a metal part of the system chas- sis. -
Page 10: Mxm Connector
Chapter 2 MXM Connector Signal Signal GBE_MDI3- GBE_MDI2- GBE_MDI3+ GBE_MDI2+ GBE_LINK100# GBE_LINK1000# GBE_MDI1- GBE_MDI0- GBE_MDI1+ GBE_MDI0+ GBE_LINK# GBE_ACT# SUS_S5# WAKE# SUS_S3# SUS_STAT# PWRBTN# SLP_BTN# LID_BTN# PWGIN MXM Connector BATLOW# RSTBTN# SATA0_TX+ SATA0_TX- SATA0_ACT# SATA0_RX+ SATA0_RX- BIOS_DISABLE#/BOOT_ALT# SDIO_CLK SDIO_CD# SDIO_LED SDIO_CMD SDIO_WP SDIO_PWR# SDIO_DAT1... - Page 11 Chapter 2 Signal Signal Signal Signal LVDS_A0- LVDS_B0- SPI_MOS0 LVDS_A1+ LVDS_B1+ SPI_SCK MFG_NC4 LVDS_A1- LVDS_B1- 5V_SB 5V_SB LVDS_A2+ LVDS_B2+ MFG_NC0 MFG_NC2 LVDS_A2- LVDS_B2- MFG_NC1 MFG_NC3 LVDS_PPEN LVDS_BLEN VCC (+5V) VCC (+5V) LVDS_A3+ LVDS_B3+ VCC (+5V) VCC (+5V) LVDS_A3- LVDS_B3- VCC (+5V) VCC (+5V) VCC (+5V) VCC (+5V)
-
Page 12: Mxm Connector Signal Description
Serial ATA Led. Open collector output pin driven during SATA command activity. Important: The DFI FS700 Series Qseven module provides Gigabit Ethernet with one Atheros AR8033 Ethernet PHY. The maximum throughput that the Gigabit Ethernet performs is limited to 470Mbps (total for Tx and Rx) due to internal bus limitations based on Fre- escale’s Errata ERR004512. - Page 13 Chapter 2 USB Interface Signals Signal Pin# Pin Type Pwr Rail /Tolerance DFI-FS700 Series Carrier Board Description USB_P0+ Connect 90 @100MHz Common Choke in series and ESD I/O USB 3.3V Suspend/3.3V Universal Serial Bus Port 0 differential pair. USB_P0- suppressors to GND to USB connector...
- Page 14 Chapter 2 LVDS Flat Panel Signals Signal Pin# Pin Type Pwr Rail /Tolerance DFI-FS700 Series Carrier Board Description Connect to enable control of LVDS panel power circuit LVDS_PPEN O CMOS 3.3V/3.3V Controls panel power enable. Connect to enable control of LVDS panel backlight powe...
- Page 15 Chapter 2 SPI Interface Signals Signal Pin# Pin Type Pwr Rail /Tolerance DFI-FS700 Series Carrier Board Description Connect a series resistor 33 to Carrier Board SPI Device SI pin 3.3V Suspend/3.3V SPI_MOSI O CMOS Master serial output/Slave serial input signal. SPI serial output data from Qseven module to the SPI device.
- Page 16 Chapter 2 Manufacturing Signals Signal Pin# Pin Type Pwr Rail /Tolerance DFI-FS700 Series Carrier Board Description This pin is reserved for manufacturing and debugging purposes. MFG_NC0 I CMOS 3.3V/3.3V May be used as JTAG_TCK signal for boundary scan purposes during production or as a vendor specific control signal. When used as a vendor specific control signal the multiplexer must be controlled by the MFG_NC4 signal.
-
Page 17: Installing Fs700 Series Onto A Carrier Board
Chapter 2 Installing FS700 Series onto a Carrier Board 2. Grasping the FS700 module by its edges, align it into the MXM connector at an angle of approximately 45 degrees. The FS700 module must be installed into the MXM connector on the carrier board without any gap between the MXM connector and the gold finger. - Page 18 Chapter 2 Important: If you do not follow the correct installation steps above, it will cause severe damage to the board and the system operation. Example 1. The FS700 module is installed into the MXM connector on the carrier board directly. FS700 Example 2.