EWM Expert XQ 2.0 Operating Instructions Manual page 4

Contents
Notes on the use of these operating instructions
5.5.4
5.5.5
5.5.6
5.6 Welding task administration (Menu) ............................................................................................. 38
5.6.1
5.6.2
5.6.3
5.6.4
5.6.5
5.6.6
5.6.7
5.6.8
5.6.9
5.7 Change welding procedure (Arc) ................................................................................................. 52
5.8 Online data transfer (network) ..................................................................................................... 52
5.8.1
5.8.2
6 Welding procedure ............................................................................................................................... 54
6.1 MIG/MAG welding ........................................................................................................................ 54
6.1.1
6.1.2
6.1.3
6.1.4
6.1.5
6.1.6
6.1.7
6.1.8
6.2 TIG welding .................................................................................................................................. 73
6.2.1
6.2.2
6.3 MMA welding ................................................................................................................................ 78
6.3.1
4
5.5.3.1 System........................................................................................................... 36
5.5.3.2 Xnet machine ................................................................................................ 36
Load configuration ........................................................................................................ 37
5.5.4.1 System........................................................................................................... 37
5.5.4.2 Xnet machine ................................................................................................ 37
Load languages and texts ............................................................................................ 37
Record on USB drive .................................................................................................... 37
5.5.6.1 Register USB drive ........................................................................................ 37
5.5.6.2 Start recording ............................................................................................... 37
5.5.6.3 Stop recording ............................................................................................... 37
JOB selection (material/wire/gas) ................................................................................. 38
JOB favourites .............................................................................................................. 39
5.6.2.1 Saving current settings to Favourites ............................................................ 39
5.6.2.2 Loading saved Favourites ............................................................................. 40
5.6.2.3 Deleting saved Favourites ............................................................................. 40
JOB manager ................................................................................................................ 40
5.6.3.1 Copy JOB to number ..................................................................................... 40
5.6.3.2 Reset current JOB ......................................................................................... 40
5.6.3.3 Reset all JOBs ............................................................................................... 40
Program sequence ....................................................................................................... 41
Programs (P 1-15) ....................................................................................................... 42
A
5.6.5.1 Overview of the welding parameter switching options .................................. 43
5.6.5.2 MIG/MAG welding ......................................................................................... 45
5.6.5.3 Advanced settings ......................................................................................... 46
5.6.5.4 TIG welding ................................................................................................... 47
5.6.5.5 MMA welding ................................................................................................. 48
Setup mode .................................................................................................................. 49
WPQR welding data assistant ...................................................................................... 50
Welding monitoring ....................................................................................................... 51
JOB display setting ....................................................................................................... 51
Wired local network (LAN) ............................................................................................ 52
Wireless local network (WiFi) ....................................................................................... 53
Welding type ................................................................................................................. 54
6.1.1.1 Welding power (operating point) ................................................................... 54
6.1.1.2 Accessory components for operating point setting ....................................... 54
6.1.1.3 Arc length ...................................................................................................... 54
6.1.1.4 Arc dynamics (choke effect) .......................................................................... 54
6.1.1.5 superPuls ...................................................................................................... 55
Operating modes .......................................................................................................... 55
6.1.2.1 Explanation of signs and functions ................................................................ 55
6.1.2.2 Automatic cut-out .......................................................................................... 67
coldArc XQ / coldArc puls XQ ....................................................................................... 68
forceArc XQ / forceArc puls XQ .................................................................................... 68
rootArc XQ / rootArc pulse XQ ..................................................................................... 69
acArc puls XQ ............................................................................................................... 70
wiredArc ........................................................................................................................ 71
Standard MIG/MAG torch ............................................................................................. 72
Operating modes (functional sequences) ..................................................................... 73
6.2.1.1 Explanation of signs and functions ................................................................ 73
6.2.1.2 Automatic cut-out .......................................................................................... 73
Arc ignition .................................................................................................................... 77
6.2.2.1 Liftarc ............................................................................................................. 77
Hotstart ......................................................................................................................... 78
099-00L105-EW501
07.06.2019