Related Manuals for SHOWTEC EventSpot 1600 Q4
Summary of Contents for SHOWTEC EventSpot 1600 Q4
- Page 1 MANUAL ENGLISH EventSpot 1600 Q4 Ordercode: 44051 Highlite International B.V. – Vestastraat 2 – 6468 EX – Kerkrade – the Netherlands...
-
Page 2: Table Of Contents
Multiple EventSpots (Master/Slave control) ......................12 Multiple EventSpots (DMX Control) ........................13 Multiple EventSpots (Wireless DMX Control) .......................14 Connect the EventSpot 1600 Q4 to the Wireless DMX signal transmitter .............15 Disconnect from the Wireless DMX signal transmitter ..................15 Fixture Linking ................................16 Data Cabling ................................16 Control Panel ................................17... - Page 3 EventSpot 1600 Q4 Maintenance ..................................29 Troubleshooting ................................30 No Light ..................................30 No Response to DMX ..............................30 Product Specifications ..............................32 Dimensions ..................................33 Notes ....................................34 Ordercode: 44051...
-
Page 4: Warning
EventSpot 1600 Q4 Warning Unpacking Instructions Immediately upon receiving this product, carefully unpack the carton and check the contents to ensure that all parts are present, and have been received in good condition. Notify the dealer immediately and retain packing material for inspection if any parts appear to be damaged from shipping or the carton itself shows signs of mishandling. - Page 5 For replacement, use fuses of same type and rating only. ● The user is responsible for correct positioning and operating of the Showtec EventSpot 1600 Q4. The manufacturer will not accept liability for damages caused by the misuse or incorrect installation of this device.
-
Page 6: Operating Determinations
EventSpot 1600 Q4 Operating Determinations ● This device is not designed for permanent operation. Regular operation breaks will ensure that the device will serve you for a long time without defects. ● The minimum distance between light-output and the illuminated surface must be bigger than 0,5 meter. -
Page 7: Connection With The Mains
EventSpot 1600 Q4 The EventSpot 1600 Q4 can be placed on a flat surface or fitted to any kind of truss with a clamp. Improper installation can cause serious damage to people and property! Connection with the mains Connect the device to the mains with the power plug. -
Page 8: Return Procedure
EventSpot 1600 Q4 Return Procedure Returned merchandise must be sent prepaid and in the original packing, call tags will not be issued. Package must be clearly labeled with a Return Authorization Number (RMA number). Products returned without an RMA number will be refused. Highlite will not accept the returned goods or any responsibility. -
Page 9: Description Of The Device
EventSpot 1600 Q4 Description of the device Features The EventSpot 1600 Q4 is a wireless LED Eventspot from Showtec. ● Long battery life ● Eco mode for extended batterylife ● IP-54 for outdoor use ● Wireless DMX by Wireless Solutions Sweden ●... -
Page 10: Overview
EventSpot 1600 Q4 Overview Fig. 01 01) Adjustment knob 02) 4 x 12W RGBW LEDs 03) OLED display + control buttons Bottom Fig. 02 04) Dedicated 3-pin DMX signal connector IN IP54 05) Main power button ON/OFF 06) Dedicated 3-pin DMX signal connector OUT IP54... -
Page 11: Backside
EventSpot 1600 Q4 Backside Fig. 03 09) Wireless DMX receiving antenna Installation Remove all packing materials from the EventSpot 1600 Q4. Check that all foam and plastic padding is removed. Connect all cables. Do not supply power before the whole system is set up and connected properly. -
Page 12: Control Modes
EventSpot 1600 Q4 Fig. 04 Important! ● Do not charge for more than 24 hours. ● Recharge within 3 days of use. ● Press the Main power button (05) to off at the underside when storing for more than 7 days. -
Page 13: Multiple Eventspots (Master/Slave Control)
EventSpot 1600 Q4 Multiple EventSpots (Master/Slave control) 01) Use a 3-p XLR cable to connect the EventSpots and other devices. The pins: 1. Earth 2. Signal (-) 3. Signal (+) 02) Link the units as shown in (Fig. 05), connect a DMX signal cable from the first unit's DMX "out" socket to the second unit's "in"... -
Page 14: Multiple Eventspots (Dmx Control)
EventSpot 1600 Q4 Multiple EventSpots (DMX Control) 01) Leave at least 0,5 meter on all sides for air circulation Use a 3-p XLR cable to connect the EventSpots and other devices. Link the units as shown in (figure 06), connect a DMX signal cable from the first unit's DMX "out"... -
Page 15: Multiple Eventspots (Wireless Dmx Control)
EventSpot 1600 Q4 Multiple EventSpots (Wireless DMX Control) 01) Place the EventSpots at the desired position (see page 15 for maximum WiFi distance). 02) When the W-DMX LED indicator (C) is blinking (green), the device is searching for a connection. -
Page 16: Connect The Eventspot 1600 Q4 To The Wireless Dmx Signal Transmitter
The LED Indicator will light up for 900ms and then dim for 100ms; The LED will flicker slowly. When the wireless DMX communication is normal, the LED indicator will always be on. The EventSpot 1600 Q4 cannot receive a wireless DMX signal and a DMX cable signal at the same time When the device is in manual, auto program or built-in program, please ensure that the matching 2.4GHz... -
Page 17: Fixture Linking
DAP Audio DMX adapter: 3-pin > 5-pin. Ordercode FLA30. ● DAP Audio DMX Terminator 3-pin. Ordercode FLA42. ● DAP Audio DMX Terminator 5-pin. Ordercode FLA43. The EventSpot 1600 Q4 can be operated with a controller in control mode or without the controller in stand-alone mode. Ordercode: 44051... -
Page 18: Control Panel
EventSpot 1600 Q4 Control Panel OLED display IR-remote sensor W-DMX LED indicator MODE button UP button SET button Power button on/off W-DMX button DOWN button Fig.09 DMX Control Mode The fixtures are individually addressed on a data-link and connected to the controller. -
Page 19: Menu Overview
EventSpot 1600 Q4 Menu overview Ordercode: 44051... -
Page 20: Main Menu Options
EventSpot 1600 Q4 First press the main power button (5) and then hold the power button (G) for at least 3 sec. to activate the EventSpot! The EventSpot will show the current software version, battery energy level, actual temperature and type of DMX signal at start-up ! Main Menu Options 01) Press the MODE or SET button to open the main menu. -
Page 21: Manual
EventSpot 1600 Q4 2. Manual In this menu you can individually set the static colors. 01) While in main menu, press the UP/DOWN buttons until the display shows Manual. 02) Press the SET button to open the menu, the display will show: Press the UP/DOWN buttons to scroll between the static colors Red, Green, Blue and White. -
Page 22: Master/Slave
EventSpot 1600 Q4 07) If you choose the strobe frequency , press the SET button to open the submenu. 08) Press the UP/DOWN buttons to set the desired strobe frequency. The adjustment range is between , from OFF to high strobe frequency. -
Page 23: Curves Select
EventSpot 1600 Q4 6.1. Curves Select In this menu you can adjust the dimming of the device by choosing a dimming curve. 01) Press the UP/DOWN buttons until the display shows Curves Select. 02) Press the SET button to open the menu, the display will show: 03) Press the UP/DOWN buttons to choose the desired dimming curve out of the 4 available options: 04) Press the SET button to confirm your choice. -
Page 24: Dmx Fail
03) Press the UP/DOWN buttons to choose between 04) If you choose , the EventSpot 1600 Q4 will have maximum output, this is the normal mode. 05) If you choose , you can set the working time from 1-15, the output will reduce but the operating time will increase to a maximum of 15Hr. -
Page 25: Lock
EventSpot 1600 Q4 6.6. Lock In this menu you can select whether the safety lock is active or not. 01) Press the UP/DOWN buttons until the display shows Lock. 02) Press the SET button to open the menu, the display will show: 03) Press the UP/DOWN buttons to select Yes or No. -
Page 26: Information
EventSpot 1600 Q4 7. Information In this menu you can view several info from the device. In main menu, press the UP/DOWN buttons until the display shows Information. Press the SET button to open the menu, the display will show: 03) You can view the currently installed software version, actual temperature, type of DMX signal and life time. -
Page 27: Auto Program
Activates the Warm white color Auto program 01) Press the button to activate Auto program. 02) The EventSpot 1600 Q4 will immediately start with its built-in program. Built-in programs 01) Press the button to activate the Built-in programs mode. 02) Press the buttons to choose between program 01-16. -
Page 28: Dmx Channels
EventSpot 1600 Q4 DMX Channels 4 Channels Channel 1 – Red Dimmer intensity 0-255 Gradual adjustment Red from 0-100% Channel 2 – Green Dimmer intensity 0-255 Gradual adjustment Green from 0-100% Channel 3 – Blue Dimmer intensity 0-255 Gradual adjustment Blue from 0-100% Channel 4 –... - Page 29 EventSpot 1600 Q4 Channel 3 – Color presets (CH1 must be set between 1-255 No function 8-13 Color 1 (R255, G000, B000, W000) 14-20 Color 2 (R255, G000, B000, W100) 21-27 Color 3 (R255, G000, B000, W200) 28-34 Color 4 (R255, G050, B000, W000)
-
Page 30: Maintenance
04) The electric power supply cables must not show any damages or material fatigue. The EventSpot 1600 Q4 requires almost no maintenance. However, you should keep the unit clean. Otherwise, the fixture’s light-output will be significantly reduced. Disconnect the mains power supply, and then wipe the cover with a damp cloth. -
Page 31: Troubleshooting
04) If all of the above appears to be in order, switch the unit on again. 05) If you are unable to determine the cause of the problem, do not open the EventSpot 1600 Q4, as this may damage the unit and the warranty will become void. - Page 32 EventSpot 1600 Q4 Problem Probable cause(s) Solution No power to the fixture • Check that power is switched on One or more and the battery is charged fixtures do not function at all Internal fuse blown • Return the device to your local...
-
Page 33: Product Specifications
EventSpot 1600 Q4 Product Specifications Model: Showtec EventSpot 1600 Q4 Input Voltage: 100-240V AC, 50/60 Hz Drive current: 650mA Refresh rate: 12KHz Battery storage: 15,6Ah Operating time at full RGBW: 8 hours Operation temperature: -10°to +40° Battery type: Litium ion... -
Page 34: Dimensions
EventSpot 1600 Q4 Dimensions Ordercode: 44051... -
Page 35: Notes
EventSpot 1600 Q4 Notes Ordercode: 44051... - Page 36 ©2018 Showtec...