Grass-Roller 2,9m 22/05-2018 EC DECLARATION OF CONFORMITY in accordance with the EU Machinery Directive 2006/42/EC applicable as from December 29 2009: HE-VA ApS N. A. Christensensvej 34, DK-7900 Nykøbing Mors hereby confirms that the following machine has been manufactured in accordance with the Council Directive 2006/42/EC.
3.8 bar/55 psi. Machine description Grass-Roller is a roller for consolidation of grassland. With water in the smooth steel rollers a high weight is achieved and with that effective consolidation which guarantees an evenly pressed grassland. This helps achieve the highest yield from the grass and good quality clean silage without soil, stones, spores etc.
Grass-Roller 2,9m 22/05-2018 Technical specifications Weight Weight without without Power Working Roller type / No. of equipm. Transport Total equipm. requirement width Ring type spokes width length with without water water Lift mounted: 2,90m 710mm Plain roller 1.035 1.995 80-120...
Grass-Roller 2,9m 22/05-2018 Safety instructions General information Do not start-up the machine if there are persons in exposed positions* within a hazardous area**. When persons are in exposed positions (e.g. in connection with adjustment, maintenance, attachment and uncoupling), the following conditions must be observed: The machine must be lowered to firm ground.
Grass-Roller 2,9m 22/05-2018 Safety - and other markings on the machine Study the Operating Instructions thoroughly before any operation of the machine and observe all safety instructions. Plate with serial number and year of manufacture. Indication label for the machine’s hydraulic systems.
Grass-Roller 2,9m 22/05-2018 Operating instructions Attachment On delivery the roller is in transport position. At start-up the roller is attached to the tractor. Important: Check that the towing hook height is between 500 and 550 mm. Raise the support leg and place it in the transport fittings on top of the drawbar. Now fit all the hydraulic hoses.
Grass-Roller 2,9m 22/05-2018 Settings and adjustment Long finger harrow The long finger harrow is raised and lowered with the hydraulic system, marked with green colour. During work the long finger harrow can be raised and lowered as required. However, take care that the harrow does not work too deeply, meaning that it will carry the whole weight of the roller.
Grass-Roller 2,9m 22/05-2018 Levelling board The levelling board is raised in proportion to the wear and tear of the tines. This is performed by loosening 2 nuts , the using a 19 mm spanner on the thread spindle, which determines the height When the desired height is reached, the 2 nuts are tightened again Be sure that all adjusters are set the same, otherwise the levelling board will operate unevenly.
After the season, the roller is to be cleaned and lubricated with grease and oil. Empty the water from the rollers to avoid frost damage. Important: The piston rods are to be lubricated with grease, for long term storage. Repairs All repairs are to be performed with original HE-VA spare parts.
Grass-Roller 2,9m 22/05-2018 Spring-Board The Spring-Board requires 1 double-acting hydraulic outlet on the tractor. The tine angle and thereby the aggressiveness of the tines is hydraulically controlled from the driver's cab and the depth control is done manually. The Spring-Board tine bar is adjustable in height and thereby the working angle of the tines against the ground is being changed.
Grass-Roller 2,9m 22/05-2018 Drawbar extension Pos. Item no. Designation 2,9m 1200001 Cpl. extended drawbar 1200050 Support leg 1030280 Pin for support leg Ø16 L=94 0377400 R-clip Ø4, galvanized Top link for 36.01 – 55.01 heavy model (36x3,0 430-620 mm) 690302011 690134004 Ring pin Ø10x40...
Grass-Roller 2,9m 22/05-2018 Roller bar Pos. Item no. Designation 2,9m 1200002 Roller bar 2,9m 1200050 Support leg 1030280 Pin Ø16 L=94 0377400 R-clip Ø4 1200034 Top link between roller bar and draw bar 690200085 Cylinder 80/40x255 Ø30/Ø30 69430130G Pin Ø30 L=130 69430094G Pin Ø30 L=94...