1. Manuals
  2. Brands
  3. DR Manuals
  4. Chipper
  5. RAPID-FEED 16.50 PRO
  6. Safety & operating instructions manual

DR RAPID-FEED 16.50 PRO Safety & Operating Instructions Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

16.50 PRO DR
SAFETY & OPERATING INSTRUCTIONS
Serial No.
Order No.
READ AND UNDERSTAND THIS MANUAL AND ALL INSTRUCTIONS BEFORE OPERATING OR
SERVICING THIS 16.50 PRO DR RAPID-FEED CHIPPER.
®
RAPID-FEED™ CHIPPER
Chipper shown with
Optional Accessories

Advertisement

Table of Contents
loading

Related Manuals for DR RAPID-FEED 16.50 PRO

Summary of Contents for DR RAPID-FEED 16.50 PRO

  • Page 1 ® 16.50 PRO DR RAPID-FEED™ CHIPPER SAFETY & OPERATING INSTRUCTIONS Chipper shown with Optional Accessories Serial No. Order No. READ AND UNDERSTAND THIS MANUAL AND ALL INSTRUCTIONS BEFORE OPERATING OR SERVICING THIS 16.50 PRO DR RAPID-FEED CHIPPER.
  • Page 2 Congratulations on your purchase of a new 16.50 PRO DR RAPID-FEED CHIPPER! We have done our utmost to ensure that your 16.50 PRO DR RAPID-FEED CHIPPER will be one of the most trouble-free and satisfying pieces of equipment you have ever owned. Please let us know of any questions you may have.

  • Page 3: Table Of Contents

    Additional Information and Potential Changes .................11 CHAPTER 3 ............................13 SETTING UP YOUR 16.50 PRO DR RAPID-FEED CHIPPER.............13 16.50 PRO DR RAPID-FEED CHIPPER Controls and Features ..........13 Unpacking the 16.50 PRO DR RAPID-FEED CHIPPER..............14 Attaching the Hopper Assembly ....................16 Attaching the Discharge Chute....................16 Attaching the Hitch Plate ......................16...
  • Page 4 Hitch Coupler Adjustment......................60 CHAPTER 8 ............................62 PARTS LIST AND SCHEMATIC DIAGRAMS................62 Parts List - 16.50 PRO DR RAPID-FEED CHIPPER ..............62 Schematic - 16.50 PRO DR RAPID-FEED CHIPPER..............63 Parts List - 16.50 PRO DR RAPID-FEED CHIPPER ..............64 Schematic - 16.50 PRO DR RAPID-FEED CHIPPER..............65 Parts List –...

  • Page 5: Chapter 1

    Representatives will be happy to help you. Conventions used in this manual Tip: This is a helpful hint to guide you in getting the most out of your 16.50 PRO DR RAPID-FEED THIS INDICATES A HAZARDOUS SITUATION, WHICH, IF NOT FOLLOWED, WILL RESULT IN DEATH OR SERIOUS INJURY.

  • Page 6: Specifications

    An Order Number is used to check and maintain your order history. The number is located on the upper left portion of your packing slip. For your convenience and ready reference, enter the Order Number in the space provided on the front cover of this manual. 16.50 PRO DR ® RAPID-FEED™ CHIPPER...

  • Page 7: Chapter 2

    Shown below are copies of all the safety and operation labels that appear on the equipment. Take a ment to study them and make a note of their location on your 16.50 PRO DR RAPID-FEED CHIPPER as you assemble and before you operate the unit. Replace damaged or missing safety and operation labels immediately.
  • Page 8 241991 241811 241821 242001 #127811 241831 242041 #242331 (electric start model only) #242611 (Road-Towing Package only) 16.50 PRO DR ® RAPID-FEED™ CHIPPER...
  • Page 9 241841 CONTACT US AT www.DRpower.com or CALL TOLL FREE 1-800-DR-OWNER...

  • Page 10: Protecting Yourself And Those Around You

    SHOES, WE RECOMMEND WEARING THEM. DO NOT USE THE MACHINE WHILE BAREFOOT OR WEARING OPEN SANDALS. • WEAR LONG PANTS WHILE OPERATING THE 16.50 PRO DR RAPID-FEED CHIPPER. • USE EAR PROTECTORS OR EAR PLUGS RATED FOR AT LEAST 20 DBA TO PROTECT YOUR HEARING.

  • Page 11: Safety For Children And Pets

    • NEVER, UNDER ANY CONDITIONS, REMOVE, BEND, CUT, FIT, WELD, OR OTHERWISE ALTER STANDARD PARTS ON THE 16.50 PRO DR RAPID-FEED CHIPPER. THIS INCLUDES ALL SHIELDS AND GUARDS. MODIFICATIONS TO YOUR MACHINE COULD CAUSE PERSONAL INJURIES AND PROPERTY DAMAGE AND WILL VOID YOUR WARRANTY.

  • Page 12: Towing Safety (Applies Only If Road-Towing Package Is Installed)

    Towing Safety (applies only if Road-Towing Package is installed) • BEFORE TOWING, BE CERTAIN THE 16.50 PRO DR RAPID-FEED CHIPPER IS CORRECTLY AND SECURELY ATTACHED TO THE TOWING VEHICLE AND THE SAFETY CHAINS ARE IN PLACE. LEAVE SLACK IN THE CHAINS TO ALLOW FOR TURNING.

  • Page 13: General Safety

    OCCURRING TO OTHER PEOPLE, THEIR PROPERTY, AND THEMSELVES. • YOUR 16.50 PRO DR RAPID-FEED CHIPPER IS A POWERFUL TOOL, NOT A PLAYTHING. EXERCISE EXTREME CAUTION AT ALL TIMES. THE DESIGN OF THIS MACHINE IS TO CHIP WOOD. DO NOT USE IT FOR ANY OTHER PURPOSE.
  • Page 14 RECOMMENDATION; SEE CHAPTER 4. PERSONAL INJURY OR DAMAGE TO THE MACHINE COULD RESULT. • WHILE USING THE 16.50 PRO DR RAPID-FEED CHIPPER, DON'T HURRY OR TAKE THINGS FOR GRANTED. WHEN IN DOUBT ABOUT THE EQUIPMENT OR YOUR SURROUNDINGS, STOP THE MACHINE AND TAKE THE TIME TO LOOK THINGS OVER.

  • Page 15: A Note To All Users

    Additional Information and Potential Changes DR Power Equipment reserves the right to discontinue, change, and improve its products at any time without notice or obligation to the purchaser. The descriptions and specifications contained in this manual were in effect at printing.
  • Page 16 16.50 PRO DR ® RAPID-FEED™ CHIPPER...

  • Page 17: Chapter 3

    It may be helpful to familiarize yourself with the controls and features of your 16.50 PRO DR RAPID-FEED CHIPPER as shown in Figure 1 before beginning these procedures. If you have any questions at all, please feel free to contact us at www.DRpower.com or call our Customer Service Representatives at our toll free number: 1-800-DR-OWNER (376-9637).

  • Page 18: Unpacking The 16.50 Pro Dr Rapid-Feed Chipper

    Discharge Package (optional Accessory) (optional Accessory) NOTE: Unpacking the 16.50 PRO DR RAPID-FEED CHIPPER is a two-person job. We recommend you have an extra set of hands available before you begin because the 16.50 PRO DR RAPID- FEED CHIPPER weighs 372 lbs. (Manual Start) and 392 (Electric Start).
  • Page 19 Top-Discharge Chute (if ordered) to the Pallet and Banding remove the Extended Top-Discharge Chute. With the help of another person, carefully remove the Hopper Assembly and roll the 16.50 PRO DR RAPID- FEED CHIPPER from the shipping pallet, resting it on the Tongue Assembly. Steel...

  • Page 20: Attaching The Hopper Assembly

    • Two 1/2" Wrenches Hitch Plate Hardware Position the Hitch Plate onto the Tongue Assembly as shown and secure with two 5/16-18 x 1" Bolts and Nylon Locknuts (Figure 9). Tongue Assembly Figure 9 16.50 PRO DR ® RAPID-FEED™ CHIPPER...

  • Page 21: Connecting The Battery Cable (Electric Start)

    NOTE: Use SAE 30 high detergent oil classified “For Service SF, SG, SH, SJ” or higher. Do not use special additives. Other types of oil could cause problems operating your machine. Please refer to your Engine Owner’s Manual for detailed oil information. CONTACT US AT www.DRpower.com or CALL TOLL FREE 1-800-DR-OWNER...
  • Page 22 (Figure 11). Be careful not to overfill and reinstall the Gas Fill Cap before starting the engine. See your Engine Owner’s Manual for more detailed information. NOTE: To refill the gas tank, turn the engine OFF and let the engine cool at least five minutes before removing the gas fill cap. 16.50 PRO DR ® RAPID-FEED™ CHIPPER...

  • Page 23: Check The Tire Pressure

    Valve Stem If the pressure is too low, add air with an air hose Protective Cap through the Valve Stem. Replace the Valve Stem Protective Cap. Figure 13 CONTACT US AT www.DRpower.com or CALL TOLL FREE 1-800-DR-OWNER...
  • Page 24 16.50 PRO DR ® RAPID-FEED™ CHIPPER...

  • Page 25: Chapter 4

    CHAPTER 4 OPERATING YOUR 16.50 PRO DR RAPID-FEED CHIPPER This chapter covers the procedures for starting and stopping your new 16.50 PRO DR RAPID-FEED CHIPPER and discusses basic operation features. • THE DESIGN OF THIS MACHINE IS FOR CHIPPING WOOD. NEVER USE THIS MACHINE FOR ANY OTHER PURPOSE AS IT COULD CAUSE SERIOUS INJURY.

  • Page 26: Operation Notes

    OF THE CHIPPER KNIFE (before each use)” in Chapter 5 for info on accessing the Chipper Knife. Hopper • At engine start-up, the engine of your DR CHIPPER operates under no load until approximately 1800 RPM, Operator at which speed the Centrifugal Clutch engages and Zone begins driving the Rotor Assembly.
  • Page 27 WHEN OVERLOADED. TURN OFF THE ENGINE IMMEDIATELY IF THE MACHINE BECOMES JAMMED TO PREVENT DAMAGE TO THE DRIVE SYSTEM. • Your DR RAPID-FEED CHIPPER can process dry or green wood up to 4.5" in diameter. • The Chipper will self-feed the wood once it contacts the knife edge so forcing the branches into the Hopper is not necessary if the knife is sharp.

  • Page 28: Starting The Engine (Manual -Starting Chipper)

    6. When the Engine is warmed up and running smoothly with the Choke in the “RUN” position, move the Throttle Cont rol Lever to the fast position (rabbit icon) Starter for chipping. Cord Figure 18 16.50 PRO DR ® RAPID-FEED™ CHIPPER...

  • Page 29: Starting The Engine (Electric-Starting Chipper)

    Choke adjustment. For chipping, operate the engine with the Throttle in the fast position (rabbit icon) with the Choke pushed in to the “RUN” position. Switch Figure 21 CONTACT US AT www.DRpower.com or CALL TOLL FREE 1-800-DR-OWNER...

  • Page 30: Stopping The Engine (Manual -Starting Chipper)

    Key becomes difficult to remove, spray FLUID FILM or a similar non-conductive lubricant into the keyhole. NOTE: Close the Fuel Shut-Off Valve when transporting or storing the DR RAPID-FEED CHIPPER. Stopping the Engine (Electric –Starting Chipper) THE FLYWHEEL WILL ST ILL ROTATE FOR A WHILE AFTER THE ENGINE IS SHUT OFF.

  • Page 31: Adjusting The Angle Of The Tongue Weldment

    AVOID DEATH OR SERIOUS INJURY. DO NOT TOW THIS MACHINE FASTER THAN 10 MPH. THIS MACHINE IS NOT LEGAL FOR STREET OR HIGHWAY USE UNLESS YOU INSTALL THE ROAD- TOWING PACKAGE (SEE “CHIPPER ACCESSORIES” IN CHAPTER 7). CONTACT US AT www.DRpower.com or CALL TOLL FREE 1-800-DR-OWNER...

  • Page 32: To Free A Jammed Flywheel

    Chipping Chamber to discharge. If the Chipping Chamber doesn’t clear and the flywheel is still jammed, repeat above process. NOTE: Be certain the Chipping Chamber is clear before trying to process more material into the Chipper Hopper. 16.50 PRO DR ® RAPID-FEED™ CHIPPER...

  • Page 33: Chapter 5

    MAINTAINING THE 16.50 PRO DR RAPID-FEED CHIPPER This chapter covers regular maintenance procedures that will ensure the best performance and long life of your DR RAPID-FEED CHIPPER. For engine maintenance, please refer to the Engine Owne r’s Manual that came with your machine. Service intervals listed in the checklist below supercede those l isted in the Engine Owner’s Manual.

  • Page 34: Grease Fittings

    Check the Set Screws for tightness. If they are not tight ® they should be removed, apply Loctite to the threads, Grease then reinstall and tighten the Set Screws. Fitting Rear Chipper Bearing (under Belt Cover) Replac e the Belt Guard Figure 24 16.50 PRO DR ® RAPID-FEED™ CHIPPER...

  • Page 35: Removing And Replacing The Engine Oil

    LUG WIRE, DISCONNECT THE NEGATIVE BATTERY CABLE, THEN WAIT 5 MINUTES BEFORE PERFORMING ANY MAINTENANCE PROCEDURE OR INSPECTION ON THE CHIPPER. USE ONLY DR BELTS ON YOUR MACHINE. THE BELTS HAVE BEEN THOROUGHLY TESTED AND PROVEN FOR MANY HOURS OF USE.
  • Page 36 (Figures 26 and 27). 2. Remove the Belt Guard. Belt Guard Figure 26 Belt Guard Hardware Figure 27 3. Remove the Locknut and Belt Guard Bracket (Figure Belt Guard 28). Bracket Locknut Figure 28 16.50 PRO DR ® RAPID-FEED™ CHIPPER...
  • Page 37 Using a Straightedge, align the Clutch and Sheave by moving the Sheave in or out on the Flywheel Shaft. Do not make the adjustment by attempting to move the Clutch on the Engine Shaft. CONTACT US AT www.DRpower.com or CALL TOLL FREE 1-800-DR-OWNER...

  • Page 38: Removing, Replacing And Adjusting The Chipper Knife And Wear Plate

    PERFORMING ANY MAINTENANCE PROCEDURE OR INSPECTION ON THE CHIPPER. ROUTINELY CHECK THE CHIPPER KNIFE FOR SHARPNESS. USING A DULL KNIFE WILL DECREASE PERFORMA NCE AND CAUSE EXCESSIVE VIBRATION THAT WILL CAUSE DAMAGE TO THE DR RAPID- FEED CHIP PER. ROUTIN Y EL CHECK THE WEAR PLATE FOR A SHARP SQUARE EDGE.

  • Page 39: Visual Inspection Of The Chipper Knife (Before Each Use)

    Inspecting the Chipper Knife and Wear Plate Routine inspection of the Chipper Knife and Wear Plate will ensure that your DR 16.50 FTP PRO Rapid eed Chipper is operating at full efficiency (see “Regular Maintenance Checklist” at the beginning of this Chap ter).
  • Page 40 (Figure 37 Allen Screws and Locknuts 6. While holding the Allen W rench, remove the Lock Nut using a 9/16" socket. Figure 37 7. Repeat Steps 5 and 6 for the remaining two Allen Screws. 16.50 PRO DR ® RAPID-FEED™ CHIPPER...

  • Page 41: Removing And Replacing The Wear Plate

    Bolts and Lo cknuts. and Locknut Plate NOTE: The Gap between the Knife and Wear Plate m ust be Figure 38 adjusted whenever the Wear Plate is rem oved. See the following instructions. CONTACT US AT www.DRpower.com or CALL TOLL FREE 1-800-DR-OWNER...

  • Page 42: Checking And Adjusting The Knife To Wear Plate Gap

    • If the Knife Gauge slides in between the Knife d Wear Plate with some resistance felt against Figure them both the n the Wear plate is properly adjusted. Install the Hopper when finished. 16.50 PRO DR ® RAPID-FEED™ CHIPPER...

  • Page 43: Chipper Knife Sharpening

    Excessive heat generated during the sharpening process will damage Knives and weaken the metal. Be sure not to overheat the Knife during sharpening because it will shorten the life of the Knife. Figure 42 CONTACT US AT www.DRpower.com or CALL TOLL FREE 1-800-DR-OWNER...

  • Page 44: Wear Plate Sharpening

    NOTE: If the Wear Plate is filed enough times that the proper gap between the Knife and Wear Plate can not be set with the Figure 44 Gap Gauge, You will ne ed to rep lace the Wear Plate. 16.50 PRO DR ® RAPID-FEED™ CHIPPER...

  • Page 45: Removing And Replacing The Wheels

    Removing and Replacing the Wheels The Wheels on the DR 16.50 FTP PRO Rapid Feed Chipper are pneumatic and have pressed in Bearings for easy trans port. With use, tires or Bearings may need replacing. The foll owing procedures will explain the replacement pr ocedures.

  • Page 46: Installing A New Clutch Assembly

    Engine speed, the more torque the Clutch can transfer to the driven unit. NEVER operate the DR RAPID-FEED CHIPPER Engine at less than full RPM when chipping. NOTE: At engine start-up, the engine of your chipper operates under no load until approximately 1800 RPM, at which speed the centrifugal clutch eng ages and begins driving the rotor.

  • Page 47: Battery Care (Electric Start Only)

    Operate the engine for at least 45 minutes to maintain proper battery charge. If the battery loses its charge, you will need to use a trickle charger (like the DR Battery Charger) to recharge it. The charger should have an output of 12 volts DC at no more than 2 amps. •...

  • Page 48: Recycling A Used Battery

    To connect a battery charger to your DR RAPID-FEED CHIPPER, follow the steps listed below. Attach the black (-) battery charger wire to the battery negative (-) terminal, and attach the red (+) battery charger wire to the battery positive (+) terminal.

  • Page 49: End Of Season And Storage

    Check the Chipper Knife and Wear Plate for nicks and wear. • For electric start models remove the battery or store your DR RAPID-FEED CHIPPER in a dry environment wh ere the temperature is between –10° F (–23° C) and +85° F (+23° C). Make sure the storage temperatures will never be outside these limits.
  • Page 50 16.50 PRO DR ® RAPID-FEED™ CHIPPER...

  • Page 51: Chapter 6

    TROUBLESHOOTING Most problems are easy to fix. Consult the Troubleshooting Table below for common problems and their solutions. If you continue to experience problems, contact us at www.DRpower.com or call DR Power Equipment for support. SHUT DOWN THE ENGINE, WAIT FOR ALL MOVING PARTS TO COME TO A COMPLETE STOP,...
  • Page 52 ⇒ Does your engine have the right amount of clean oil? If it’s dirty, change it following the procedure in Chapter 5. ⇒ If your engine still lacks power, contact us at www.DRpower.com or call 1(800) DR-OWNER (376-9637) for assistance. Engine smokes. ⇒ Check the oil level and adjust as needed.
  • Page 53 Clutch parts. See Chapter 5. rotate. ⇒ Loose Drive Belt; adjust the Drive Belt tension. See Chapter 5. ⇒ Remove any built-up debris from the Chipper Hopper Inlet and Discharge Chute. CONTACT US AT www.DRpower.com or CALL TOLL FREE 1-800-DR-OWNER...
  • Page 54 60 psi in ea should be 60 psi in ea ch tire if you have the road towing option. ch tire if you have the road towing option. while being towed. while being towed. 16.50 PRO DR ® RAPID-FEED™ CHIPPER...

  • Page 55: Chapter 7

    Bolt o Bolt s and Locknuts and tighten with s and Locknuts and tighten with two 1/2" wre two 1/2" wre nches. nches. Bolt and Locknut Locking (2 places) Figure 48 CONTACT US AT www.DRpower.com or CALL TOLL FREE 1-800-DR-OWNER...

  • Page 56: Operation

    Rotate the Extended Top-Discharge Chute for the full 180˚ of rotation for a few times to spread the grease inside the Discharge Ring. 4. Reposition the Extended Top-Discharge Chute to the desired angle and insert the Locking Pin and Hitch Clip. 16.50 PRO DR ® RAPID-FEED™ CHIPPER...

  • Page 57: Road-Towing Package

    If there are any questions contact us at www.DRpower.com or call 1-800-DR-OWNER (376- 9637). Do not discard the shipping materials until you are fully satisfied with your new Road-Towing Package. Figure 53 CONTACT US AT www.DRpower.com or CALL TOLL FREE 1-800-DR-OWNER...

  • Page 58: Installation

    Chipper wheels off the ground (Figure 56). The Spacer (behind lowermost part of frame must be at least 10" from the Jack wheel) Stands ground for the Wheel Assembly to fit under. Figure 56 16.50 PRO DR ® RAPID-FEED™ CHIPPER...
  • Page 59 Locknuts and Washers (on the side with slots) and two Bolts and Locknuts (on side with holes) us ing two 9/16" wrenches (Figure 59). Axle Axle Assembly Assembly Hardware Figure 59 CONTACT US AT www.DRpower.com or CALL TOLL FREE 1-800-DR-OWNER...
  • Page 60 17. Jack the back of the Chipper up and remove the jack Wheel Stands. Assembly 18. Lower the Chipper to the ground. 19. Check the Tire for proper air pressure o f 60 psi maximum in each Tire. Figure 62 16.50 PRO DR ® RAPID-FEED™ CHIPPER...
  • Page 61 Push the Green Wire into the top right hole in the back of the light socket and p ush the Brown Wire into the top left hole. Side Light Figure 65 CONTACT US AT www.DRpower.com or CALL TOLL FREE 1-800-DR-OWNER...
  • Page 62 NOTE: We recommend that you wrap the Harness Wires together with e lectrical tape about every twelve inches starting at the W Figure 68 Harness Connector end and going back to where the wires go to either side of the Frame. 16.50 PRO DR ® RAPID-FEED™ CHIPPER...

  • Page 63: Towing

    Vehicle and ensure that your lights on the Chipper are working properly. Lock or Lock Pin If there are any questions, contact us at www.DRpower.com or call 1-800-DR-OWNER (376-9637). Latch Assembly Figure 71 CONTACT US AT www.DRpower.com or CALL TOLL FREE 1-800-DR-OWNER...

  • Page 64: Hitch Coupler Adjustment Check

    Then back off the lock nut 1/2 turn or Lock Nut just enough that the latch is able to clamp and unclamp from the ball. Ball Clamp Figure 73 16.50 PRO DR ® RAPID-FEED™ CHIPPER...
  • Page 65 CONTACT US AT www.DRpower.com or CALL TOLL FREE 1-800-DR-OWNER...

  • Page 66: Chapter 8

    CHAPTER 8 PARTS LIST AND SCHEMATIC DIAGRAMS Parts List - 16.50 PRO DR RAPID-FEED CHIPPER NOTE: Part numbers listed are available through DR P ower Equipment. Ref# Part# Description Ref# Part# Description 2420 Chipper Basic Assembly 241611 Bolt, 1/4-20 X 1 ", GR 5...

  • Page 67: Schematic - 16.50 Pro Dr Rapid-Feed Chipper

    Schematic - 16.50 PRO DR RAPID-FEED CHIPPER CONTACT US AT www.DRpower.com or CALL TOLL FREE 1-800-DR-OWNER...

  • Page 68: Parts List - 16.50 Pro Dr Rapid-Feed Chipper

    Parts List - 16 .50 PRO DR RAPID-FEED CHIPPER NOTE: Part numbers listed are available through DR Power Equipment. Ref# Part# Description Ref# Part# Description 242181 Base Weldment 241701 Bolt, Carriage, 5/16-18 X 3" 242191 Bracket, Axle 242251 Axle, 3/4" OD 154490 Bolt, 3/8-16 X 1-1/4", GR 5...

  • Page 69: Schematic - 16.50 Pro Dr Rapid-Feed Chipper

    Schematic - 16.50 PRO DR RAPID-FEED CHIPPER CONTACT US AT www.DRpower.com or CALL TOLL FREE 1-800-DR-OWNER...

  • Page 70: Parts List - Chipper Basic

    Parts List – Chipper Basic NOTE: Part numbers listed are available through DR Power Equipment. Ref# Part# Description Ref# Part# Description 155301 Screw, 3/8-16 X 1-3/4", FHSCS, 242491 Bolt, 5/16-18 X 5-1/4", GR 5 GR 8 146051 Bolt, 5/16-18 X 1", GR 5...

  • Page 71: Schematic - Chipper Basic

    Schematic - Chipper Basic CONTACT US AT www.DRpower.com or CALL TOLL FREE 1-800-DR-OWNER CONTACT US AT www.DRpower.com or CALL TOLL FREE 1-800-DR-OWNER...

  • Page 72: Parts List - Hopper Assembly

    Parts List – Hopper Assem NOTE: Part numbers listed are available through DR Power Equipment. Ref# Part# Description Ref# Part# Description 242511 Hopper Weldment, Bottom 241621 Bolt, Philips Head, 5/16-18 X 1/2", GR 5 242521 Hoppe r Weldment, Left 241631...

  • Page 73: Schematic - Hopper Assembly

    Schematic – Hopper Assembly CONTACT US AT www.DRpower.com or CALL TOLL FREE 1-800-DR-OWNER...

  • Page 74: Parts List - Accessories

    Parts List – Accessories NOTE: Part numbers listed are available through DR Power Equipment. ROAD-TOWING PACKAGE EXTENDED T DISCHARGE CHUTE Ref# Part# Description Ref# Part# Description 242571 Tongue Weldment, Highway 242621 Flange, Side 161011 Hitch, Trailer 242631 Plate, Bottom 148911...

  • Page 75: Schematic - Accessories

    Schematic – Accessories CONTACT US AT www.DRpower.com or CALL TOLL FREE 1-800-DR-OWNER...
  • Page 76 16.50 PRO DR ® RAPID-FEED™ CHIPPER...

  • Page 77: Notes

    Notes: CONTACT US AT www.DRpower.com or CALL TOLL FREE 1-800-DR-OWNER...
  • Page 78 16.50 PRO DR ® RAPID-FEED™ CHIPPER...
  • Page 79 Technical Service Department for our Owners. You can access a Representative by dialing our TOLL-FREE Hotline at 1- 800-DR-OWNER (376-9637). The sole job of our well-trained and friendly folks is to ensure that you get any help you need in a timely fashion. They are there to answer all your questions including: (1) inquiries on any of the above warranties, (2) inquiries about replacement parts, or (3) your questions regarding service, maintenance and operation.

  • Page 80: Daily Checklist For The 16.50 Pro Dr Rapid-Feed Chipper

    Daily Checklist for the 16.50 PRO DR RAPID-FEED CHIPPER To help maintain your 16.50 PRO DR RAPID-FEED CHIPPER for optimum performance, we recommend you follow this checklist each time you use your Chipper. SHUT DOWN THE ENGINE, WAIT FOR ALL MOVING PARTS TO COME TO A COMPLETE STOP, REMOVE SPARK PLUG WIRE, DISCONNECT THE NEGATIVE BATTERY CABLE, THEN WAIT 5 MINUTES BEFORE PERFORMING ANY MAINTENANCE PROCEDURE OR INSPECTION ON THE CHIPPER.

Table of Contents