Johnson Controls CIS01 Installation & Maintenance Manual page 16

No. Items Optional Function
Cooling/Heating Changeover
133 r2
Temperature
134 r3 Setback Temperature Compensation
135 r4 Not Prepared
136 r5 Not Prepared
137 r6 Not Prepared
138 r7 Not Prepared
139 r8 Not Prepared
140 r9 Not Prepared
141 rA Not Prepared
142 rb Not Prepared
143 S1 Not Prepared
144 S2 Not Prepared
145 S3 Not Prepared
146 S4 Not Prepared
147 S5 Not Prepared
148 S6 Not Prepared
149 S7 Not Prepared
150 S8 Not Prepared
(*1): The "02", "03", "04" settings may not be available depending on the type of indoor unit.
When connecting multiple indoor units, do separate settings.
(*2): If Duct type models, 00: Increasing fan speed 1 (standard), 01: Increasing fan speed 2 (high static pressure),
02: Standard (low static pressure).
(*3): If the set temperature is changed and kept within the set time at "F4", the temperature is automatically changed to
"F5" and "F6". (If the set temperature is out of range at "F5" and "F6", it is applied within the upper and lower limits
for the set temperature.)
(*4): Applicable to the fan, cooling and dry operation modes.
(*5): Applicable to the heating operation mode.
(*6): Operation is stopped by pressing the " " (On/Off) button for 3 seconds.
(*7): "01" is available only when one controller is used. Do not use this setting when two (primary-secondary)
controllers are used.
(*8): Change the temperature unit (°F or °C) via the " " and " " (Temp switch). Push simultaneously after setting "01"
(Unlock) of this function (H6). Default is "°F".
(*9) If the operation on the controller is locked by this function (J4), Run/Stop state cannot be changed even in the
emergency. Make sure that this lock will NOT cause any inconvenience.
(*10): When the unit is restarted by the controller, the temperature automatically changes to the setting temperature of
"F5" or "F6".
NOTE:
1. Power on, wait 3 minutes and then change the optional setting.
2. When changing the "CF" setting (change of louver swing angle), restore the power supply or allow the louver to
make one complete swing fully in the auto-swing mode and then apply the optional setting.
3. The optional settings may be different according to the indoor and outdoor unit models.
Verify that the unit has the optional setting.
4. Record the setting conditions for each optional setting in the "Setting" column of the table below.
5. The above optional functions marked with an "X" at the individual setting can change the condition only when "All
Rooms" is set.
14
Individual Setting
Setting Condition
o
2(1.0) 2 F (1.0
o
3(1.5) 3 F (1.5
×
o
4(2.5) 4 F (2.5
o
5(3.0) 5 F (3.0
o
1(0.5) 1 F (0.5
o
4(2.5) 4 F (2.5
o
5(3.0) 5 F (3.0
o
6(3.5) 6 F (3.5
o
7(4.0) 7 F (4.0
o
8(4.5) 8 F (4.5
×
o
9(5.0) 9 F (5.0
o
10(5.5) 10 F (5.5
o
1(0.5) 1 F (0.5
o
2(1.0) 2 F (1.0
o
3(1.5) 3 F (1.5
- - Not Used (Use as 00 setting conditions)
- - Not Used (Use as 00 setting conditions)
- - Not Used (Use as 00 setting conditions)
- - Not Used (Use as 00 setting conditions)
- - Not Used (Use as 00 setting conditions)
- - Not Used (Use as 00 setting conditions)
- - Not Used (Use as 00 setting conditions)
- - Not Used (Use as 00 setting conditions)
- - Not Used (Use as 00 setting conditions)
- - Not Used (Use as 00 setting conditions)
- - Not Used (Use as 00 setting conditions)
- - Not Used (Use as 00 setting conditions)
- - Not Used (Use as 00 setting conditions)
- - Not Used (Use as 00 setting conditions)
- - Not Used (Use as 00 setting conditions)
- - Not Used (Use as 00 setting conditions)
Contents
o
C)
o
C)
o
C)
o
C)
o
C)
o
C)
o
C)
o
C)
o
C)
o
C)
o
C)
o
C)
o
C)
o
C)
o
C)
Setting
P5415520