bora PKT11 Operating And Installation Instructions
Tepan stainless steel grill
Hide thumbs
Also See for PKT11:
- Operating and installation instructions (32 pages) ,
- Operating and installation instructions (32 pages)
Related Manuals for bora PKT11
Summary of Contents for bora PKT11
- Page 1 Operating and installation instructions PKT11 Tepan stainless steel grill PKT11UMEN-000 1038521 www.bora.com...
- Page 2 Please accept our apologies in this eventuality. An updated version can be requested from the BORA Service Team. Subject to printing errors and mistakes.
-
Page 3: Table Of Contents
General operating instructions ......22 Initial operation ..........22 Operating the cooktop ........22 6.3.1 Switch on the grilling zone ........ 22 6.3.2 Power setting ........... 23 6.3.3 Bridging function ..........23 6.3.4 Cleaning function ..........24 6.3.5 Childproofing feature ......... 24 www.bora.com... -
Page 4: General Information
& Co KG, BORA APAC Pty Ltd and BORA Lüftungstechnik GmbH - hereinafter referred Target group to as BORA - do not assume any liability for damage arising from non-adherence to these These operating and installation instructions apply for the... - Page 5 Caution Indicates a potentially hazardous situation which could lead to slight or minor injuries if ignored. — Caution Indicates a situation which could result in material damage if ignored. Tab. 1.2 Meaning of warning symbols and signal words www.bora.com...
-
Page 6: Safety
In recirculation mode, only a slight underneath. amount of moisture is removed from Make sure no water penetrates inside the the cooking vapour. device when cleaning. Only use a slightly damp cloth. Never spray water on the device. Water ingress can cause damage! www.bora.com... -
Page 7: Safety Instructions - Operation
Unattended pans can boil over allowing hot liquids to escape. Always keep an eye on pans while cooking. Short cooking sessions must be constantly monitored. Safety instructions – installation The device must only be installed and assembled by trained specialists who are www.bora.com... -
Page 8: Safety Instructions - Disassembly And Disposal
Make sure that the connection Use an authorised measuring cable is not squashed or damaged. device to ensure that there is no power to the appliance. www.bora.com... -
Page 9: Safety Instructions - Spare Parts
INFO Store all packaging components BORA Holding GmbH, BORA Vertriebs out of reach of children. GmbH & Co KG, BORA APAC Pty Ltd Dispose of the packaging properly and BORA Lüftungstechnik GmbH do and immediately. not assume any liability for damage arising from non-adherence to the safety and warning information. -
Page 10: Technical Data
295 x 230 mm 2400 W Temperature control range 70–250° C Tab. 3.1 Technical data Device dimensions control knob Fig. 3.2 PKT11 Device dimensions aerial view 10-40 29,5 Fig. 3.3 PKT11 Device dimensions front view 18,5 Fig. 3.1 Device dimensions control knob Fig. -
Page 11: Device Description
Control knob for the back grilling zone Control knob for the front grilling zone Fig. 4.4 Control knob display elements Display of functions Power display Front cooking zone display Display of mode or operating mode Rear cooking zone display www.bora.com... -
Page 12: Functional Principle
The power output of the Tepan stainless steel grill heats 120 minutes for the timer functions. food extremely quickly. A slight adjustment is needed in comparison to conventional cooking systems when selecting the temperature in order to avoid burning food. www.bora.com... -
Page 13: Pause Function
(see the Operation section). 4.4.2 Safety shut-down Each grill zone is switched off automatically if it exceeds the maximum operating duration at a power level or heat retention level. The control knob display shows (residual heat display). www.bora.com... -
Page 14: Installation
If there are any missing or damaged parts, please Make sure that the cutting surfaces of the worktops notify BORA After Sales Service immediately. are properly sealed. Do not under any circumstances install parts which are Comply with the instructions of the worktop damaged. -
Page 15: Flush Installation
Cross bars on the kitchen unit in the area of the worktop cut-out may need to be removed. Fig. 5.5 Surface mounting The drawers and/or shelves in the floor unit must be removable for maintenance and cleaning purposes. Make sure that the area below the cooktop is sufficiently ventilated. www.bora.com... -
Page 16: Optional Cable Protection
Screw the fixing nut onto the control knob from the rear and tighten a little. Use the marking to align the control knob vertically in the 12 o’clock position. Tighten the fixing nut. Place the knob ring on the control knob. www.bora.com... -
Page 17: Installing The Cooktop
Bore holes for 3 cooktops and 2 extractors Fig. 5.14 Cooktop and height adjustment plates Bore holes for socket (2x external) Cooktop Bore holes for control knobs (8x) Height adjustment plates Cooktop 3x Cooktop extractor (2x) Worktop Floor unit panel www.bora.com... -
Page 18: Seal The Cooktop
If installation is rotated around 180°, then the connections for the control knob and the Fig. 5.18 Connection the control knob on the back extraction system are at the front. Connection the control knob on the back INFO Cables of sufficient length are supplied. www.bora.com... -
Page 19: Establishing The Power Connection
1-phase connection 1 x 25 A 2.5 mm² 2-phase connection 2 x 16 A 2.5 mm² 5.6.2 Select menu option Turn the knob ring to select the menu option you want. Tab. 5.3 Fuse protection and minimum cross-section www.bora.com... -
Page 20: Changing The Setting
Demo mode is used, Tab. 5.9 Control knob display options for example, for exhibitions. 5.6.3 Changing the setting Turn the knob ring clockwise to increase the value. Turn the knob ring anticlockwise to decrease the value. www.bora.com... -
Page 21: Exiting Configuration Menu
Explain all safety-related aspects of operation and handling to the user. Affix the nameplate supplied to the back of these operating and installation instructions. Provide the user with the accessories and the operating and installation instructions for safe storage. www.bora.com... -
Page 22: Operation
Cleaning function and other temperature is reached. temperature levels While it is heating up, you can press the touch surface Power levels 1 - 9 for 1 second to display the set temperature. Power setting Timer function Tab. 6.1 Knob ring positions www.bora.com... -
Page 23: Power Setting
If the highest of the low power levels has been reached, the power level is reduced by one power level INFO If the bridging function is activated, the every time the touch surface is touched for 1 second. temperature is only displayed on the right hand control knob. www.bora.com... -
Page 24: Cleaning Function
12 o’clock position and there are no deactivated and the control knob display switches to active functions. Press the touch-surface within 3 seconds to confirm the time set. A beep sounds and the set value starts to flash on the control knob display. www.bora.com... -
Page 25: Stop Function (Pause)
The cooking session is interrupted. INFO The cooking session can be paused for a maximum of 10 minutes. If the pause function is not deactivated in this time, the relevant cooking zone is switched off. www.bora.com... -
Page 26: Cleaning And Maintenance
Only use the scraper on the grill surface, as Any changes in colour or little scratches are not damage otherwise it could damage the surface. to the cooktops. They do not affect the functionality of INFO Only clean the stainless steel in the polishing direction. www.bora.com... -
Page 27: Cleaning The Control Knobs
Dry the touch surface and the knob housing carefully. Place the knob ring back on the knob housing. INFO If the knob ring has not been fitted correctly, a segment rotating clockwise is displayed in the central control knob display www.bora.com... -
Page 28: Troubleshooting
After troubleshooting, turn the knob ring to the 12 o’clock position (0 position). In all other cases, contact the BORA Service Team (see section ‘Warranty, technical service and spare parts) and enter the error number displayed and the device type. -
Page 29: Decommissioning, Disassembly And Disposal
Remove the device from the worktop by lifting it for return and recycling electrical and electronic upwards. components and other materials. Remove any other accessories. Dispose of the old device and any contaminated accessories as described under “ Environmentally- friendly disposal”. www.bora.com... -
Page 30: Warranty, Technical Service And Spare Parts
BORA specialist supplier or the BORA Service Team. The BORA Service Team requires the type designation and the build number of your appliance (FD number). Both pieces of information can be found on the nameplate on the back of the instructions and on the appliance base. - Page 32 F +49 (0) 8035 / 907-249 F +61 2 8076 3514 info@bora.com info@boraapac.com.au www.bora.com www.boraapac.com.au Austria: BORA Vertriebs GmbH & Co KG Prof.-Dr.-Anton-Kathrein-Straße 3 6342 Niederndorf Austria T +43 (0) 5373 / 62250-0 F +43 (0) 5373 / 62250-90 mail@bora.com www.bora.com...