Adjusting the power level ......17 Cleaning and Maintenance Cleaning agents ..........18 Maintaining the cooktop ........ 18 Cleaning the cooktop ........18 7.3.1 Cleaning the stainless steel grill surface ..18 7.3.2 Cleaning the control knobs ......19 Troubleshooting www.bora.com...
General General INFO BORA Holding GmbH, BORA Vertriebs GmbH & Co KG, BORA APAC Pty Ltd and BORA Lüftungstechnik GmbH - hereinafter referred Target group to as BORA - shall not assume any liability for damage caused by non-compliance with these...
Page 5
CAUTION Indicates a possible hazard- ous situation which can cause minor injury if not respected. — CAUTION Indicates a situation which can cause minor injury if not respected. Tab. 1.2: Meaning of the warning symbols and signal words www.bora.com...
Ensure a normal and comfortable indoor climate the cooking zone are clean and dry. (45-60% humidity), e.g. through natural ventilation Always lift (do not drag!) the cookware to prevent openings or domestic ventilation systems. scratching and abrasion on the surface. www.bora.com...
Make sure that the connection cable does cooktop can heat up and ignite. not come into contact with hot cooking Do not leave any objects on the cooktop. surfaces. Make sure that the connection cable is not caught or damaged. www.bora.com...
Work on electrical parts may only be carried out by trained BORA shall not assume any liability for damages caused by electrical personnel. improper use or incorrect operation.
Front cooking zone 300 x 235 mm 2400 W Back cooking zone 300 x 235 mm 2400 W Temperature control range 60 - 250°C Tab. 3.1: Technical data Device dimensions Fig. 3.1 Device dimensions Fig. 3.2 Control box dimensions www.bora.com...
Browning breaded or battered fish, pancakes, sausages, pork, lamb Browning potato fritters, prawns, corn on the cob and escalopes Fast browning beef, fish, meatballs Tab. 4.2: Recommendations for power levels Fig. 4.2 Control knobs The specifications provided in the table are standard values. www.bora.com...
If there are any missing or damaged parts, please notify BORA After Sales Service immediately. Do not under any circumstances install parts which are damaged. Dispose of transport packaging in the proper manner (see the Decommissioning and Disposal chapter).
Fig. 5.3 Dimension of groove for flush installation 1116 1088 INFO If the induction glass ceramic wok is used, the groove dimensions must be increased to 7 mm for flush installation. 1338 1310 1709 1681 Tab. 5.2: Cut-out dimensions www.bora.com...
Fig. 5.8 Control box structure Control box Adjustment plates Fixed front panel (not included in scope of delivery) Power level sleeve Nuts Control knobs Draw the bore holes accordingly with the aid of the drilling template provided. www.bora.com...
Page 14
For fine adjustment, the distance between the control plates knob and the power level sleeve can be set. [mm] Fig. 5.11 Position control knob 18,5 mm Tab. 5.3: Adjustment plate overview Fig. 5.12 Distance of the control knob www.bora.com...
Firstly connect the yellow/green earthing cable to the indicated point on the control box. Cooktop Height adjustment plates Earthing symbol Now connect the multi-pin, colour-coded plugs on the relevant cooking zone to the corresponding colour-coded sockets on the control box. www.bora.com...
Switch off the main switch/automatic circuit breaker before connecting the cooktop. Protect the main switch/automatic circuit breaker from being switched on without permission. Make sure the device is not energised. Only connect the cooktop using a permanent connection to a power supply cable. www.bora.com...
250°C slightly brown. If the grill plate is used frequently, the grilling surface may bulge slightly in the middle over the central zone division. Switching cooktop on/off Fig. 6.1 Push and pull control knob www.bora.com...
Remove any baked-on grill residues from the grill surface with a plastic brush. INFO When the cooktop extractor is switched on, Remove the remaining soiling and residual water-citric the stainless steel grease filter must be mixture (citric acid) completely with a clean cloth. www.bora.com...
Pull off the control knob. Clean the control knob with a soft brush. Rinse the control knob well after cleaning. Allow the control knob to dry thoroughly. Re-insert the clean and dry control knob into the slot after the cleaning is completed. www.bora.com...
Wait a few operating hours. Contact new cooktop is put into operation. appliances. BORA After Sales Service if the odour persists. Tab. 8.1: Resolving a fault In all other instances, call BORA After Sales Service (see the Warranty, After Sales and Spare parts chapter). www.bora.com...
Therefore do not dispose of your old appliance as household waste. Take the old appliance to a regional collection centre for return and recycling of electronic and electrical parts and other materials. www.bora.com...
10.3 Spare parts Only use original spare parts when making repairs. INFO Spare parts can be obtained from your BORA dealer, the BORA online service website at www.bora.com/service or by calling the service number provided.
Page 24
F +49 (0) 8035 / 907-249 F +61 297 /124 131 info@bora.com info@boraapac.com.au www.bora.com www.boraapac.com.au Austria: BORA Vertriebs GmbH & Co KG Prof.-Dr.-Anton-Kathrein-Straße 3 6342 Niederndorf Österreich T +43 (0) 5373 / 62250-0 F +43 (0) 5373 / 62250-90 mail@bora.com www.bora.com...