bora PKT11 Operating And Installation Instructions
Tepan stainless steel grill
Hide thumbs
Also See for PKT11:
- Operating and installation instructions (32 pages) ,
- Operating and installation instructions (32 pages)
Related Manuals for bora PKT11
Summary of Contents for bora PKT11
- Page 1 Operating and installation instructions PKT11 Tepan stainless steel grill PKT11UMEN-001 1038521 www.bora.com...
- Page 2 Please accept our apologies in this eventuality. An updated version can be requested from the BORA Service Team. Subject to printing errors and mistakes.
-
Page 3: Table Of Contents
General operating instructions ......22 Initial operation ..........22 Operating the cooktop ........22 6.3.1 Switching on the grilling zone ......22 6.3.2 Power setting ........... 23 6.3.3 Bridging function ..........23 6.3.4 Cleaning function ..........24 6.3.5 Childproofing feature ......... 24 www.bora.com... -
Page 4: General Information
& Co KG, BORA APAC Pty Ltd and BORA Lüftungstechnik GmbH - hereinafter referred Target group to as BORA - do not assume any liability for damage arising from non-adherence to these These operating and installation instructions apply for the... - Page 5 Caution Indicates a potentially hazardous situation which could lead to slight or minor injuries if ignored. — Caution Indicates a situation which could result in material damage if ignored. Tab. 1.2 Meaning of warning symbols and signal words www.bora.com...
-
Page 6: Safety
In recirculation mode, only a slight underneath. amount of moisture is removed from Make sure no water penetrates inside the the cooking vapour. device when cleaning. Only use a slightly damp cloth. Never spray water on the device. Water ingress can cause damage! www.bora.com... -
Page 7: Safety Instructions - Operation
Keep children away from the conductor system that has been installed in cooktop when it is hot or ensure line with regulations. Ensure that this basic they are supervised at all times. safety precaution is met. www.bora.com... -
Page 8: Safety Instructions - Disassembly And Disposal
Only use original spare parts for Check the appliance for visible damage repairs. before installing it. Do not install damaged devices. A damaged device is a hazard. Repair work must only be carried out by specialists authorised by the manufacturer. www.bora.com... -
Page 9: Intended Use
Any use other than that specified in these operating and installation instructions or any use that goes beyond that which is described here is classed as unintended. BORA does not assume any liability for damages caused by improper use or incorrect operation. -
Page 10: Technical Data
295 x 230 mm 2400 W Temperature control range 70–250° C Tab. 3.1 Technical data Device dimensions control knob Fig. 3.2 PKT11 Device dimensions aerial view 10-40 29,5 Fig. 3.3 PKT11 Device dimensions front view 18,5 Fig. 3.1 Device dimensions control knob Fig. -
Page 11: Device Description
(at the back) Control knob for the rear grilling zone Control knob for the front grilling zone Fig. 4.4 Control knob display elements Display functions Power display Front grilling zone display Mode or operating mode display Rear grilling zone display www.bora.com... -
Page 12: Functional Principle
4.3.2 Temperature ranges The power output of the Tepan stainless steel grill heats food extremely quickly. To avoid burning food, slight adjustment is needed in comparison to conventional cooking systems when selecting the temperature. www.bora.com... -
Page 13: Timer Functions
It can only be activated appears on the control knob display (residual heat when all grilling zones are switched on (see the Operation display). The display goes out after a sufficient cooling section). time (temperature < 50°C). www.bora.com... -
Page 14: Installation
Comply with the instructions of the worktop If there are any missing or damaged parts, please manufacturer. notify BORA After Sales Service immediately. 5.4.1 Worktop overhang Do not under any circumstances install parts which are damaged. Dispose of transport packaging in the proper manner ≥74... -
Page 15: Flush Installation
Cross bars on the kitchen unit in the area of the worktop cut-out may need to be removed. The drawers and/or shelves in the floor unit must be removable for maintenance and cleaning purposes. Make sure that the area below the cooktop is sufficiently ventilated (see ‘Air supply cooktop’). www.bora.com... -
Page 16: Air Supply Cooktop
Air supply via the plinth area Push the control knob through the drilled hole in the floor unit panel from the front. Air supply in the plinth area through the plinth panel Air supply in the plinth area through the body www.bora.com... -
Page 17: Installing The Cooktop
If applicable, insert the height adjustment plates [2]. Fig. 5.13 Bore holes for 3 cooktops and 2 extractors Bore holes for socket (2x external) Bore holes for control knobs (8x) Cooktop 3x Cooktop extractor (2x) Worktop Floor unit panel www.bora.com... -
Page 18: Seal The Cooktop
If installation is rotated around 180°, then the connections for the control knob and the extraction system are at the front. Fig. 5.19 Connection the control knob on the back INFO Cables of sufficient length are supplied. Connection the control knob on the back www.bora.com... -
Page 19: Establishing The Power Connection
If necessary, the user can the ask the public power supply company for the system impedance at the interface point. www.bora.com... -
Page 20: Accessing The Configuration Menu
Factory setting C 00 Combination display C 32 10% (min. volume) C0 1 Tab. 5.8 Control knob display C 02 C 03 C 04 C 05 C 06 C 07 C 08 C 09 Tab. 5.5 Warning beep volume www.bora.com... -
Page 21: Changing The Setting
Turn the knob ring anticlockwise to decrease the value. Press the touch surface on the control knob again for 1 second to confirm the new setting. The value is saved and a beep sounds. The previously selected menu option is shown again on the control knob display. www.bora.com... -
Page 22: Operation
Each grilling zone has its own control knob. The left knob controls the front grilling zone, the right knob controls the rear grilling zone. Fig. 6.2 Switching on the grilling zone Turn the selector ring from the 12 o’clock position to a power level. www.bora.com... -
Page 23: Power Setting
Turn the selector ring approximately 15° clockwise the same time for at least 1 second. from the 12 o’clock position until it engages. appears on the left control knob and on the right appears on the control knob display. one. www.bora.com... -
Page 24: Cleaning Function
If no time is set within the 3 seconds, the timer will be deactivated and t will appear on the control knob. Press the touch-operated area within 3 seconds to confirm the set time. An acoustic signal sounds and the set value starts to flash on the control knob display. www.bora.com... -
Page 25: Stop Function (Pause)
The cooking session is interrupted. INFO The cooking session can be paused for a maximum of 10 minutes. If the stop function is not disabled again by the end of this period, the applicable cooking zone will be switched off. www.bora.com... -
Page 26: Cleaning And Maintenance
INFO Only clean the stainless steel in the polishing surface. direction. Changes in the colour of the cooktop are the result of residue which has not been removed and has burnt on. www.bora.com... -
Page 27: Cleaning The Control Knobs
Dry the touch surface and the knob housing carefully. Place the knob ring back on the knob housing. INFO If the knob ring has not been fitted correctly, a segment rotating clockwise is displayed in the central control knob display www.bora.com... -
Page 28: Troubleshooting
After troubleshooting, turn the knob ring to the 12 o’clock position (0 position). In all other cases, contact the BORA Service Team (see section ‘Warranty, technical service and spare parts) and enter the error number displayed and the device type. -
Page 29: Decommissioning, Disassembly And Disposal
Remove the device from the worktop by lifting it for return and recycling electrical and electronic upwards. components and other materials. Remove any other accessories. Dispose of the old device and any contaminated accessories as described under “ Environmentally- friendly disposal”. www.bora.com... -
Page 30: Warranty, Technical Service And Spare Parts
BORA specialist supplier or the BORA Service Team. The BORA Service Team requires the type designation and the build number of your appliance (FD number). Both pieces of information can be found on the nameplate on the back of the instructions and on the appliance base. - Page 32 F +49 (0) 8035 / 907-249 F +61 2 8076 3514 info@bora.com info@boraapac.com.au www.bora.com www.bora-australia.com.au Austria: BORA Vertriebs GmbH & Co KG Prof.-Dr.-Anton-Kathrein-Straße 3 6342 Niederndorf Austria T +43 (0) 5373 / 62250-0 F +43 (0) 5373 / 62250-90 mail@bora.com www.bora.com...
Need help?
Do you have a question about the PKT11 and is the answer not in the manual?
Questions and answers