Sony TRIMASTER HX BVM-HX310 Operating Instructions Manual page 23

Submenu Setting
Input Set the input connector of the SDI 4K
signal.
 Input1,2,3&4: Select to use SDI IN
Input1&2: Select to use SDI IN 

Input3&4: Select to use SDI IN 

 Input1
Input3

1) Displayed only on the "SDI2 4K/UHD
Input Setting" menu. Select this
when the 12G/6G-SDI signal is
input.
Interface Format Displays the interface format of the SDI
4K signal.
 Quad-Link 3G/HD-SDI (Default
value)
 Dual-Link 3G-SDI
 Single-Link 12G/6G-SDI
1) Displayed only on the "SDI2 4K/UHD
Input Setting" menu.
Image Division Set the image division of the SDI 4K
signal.
 Auto: Select for the Auto setting.
 2SI: Select to receive images of the 2
 Square: Select to receive images of
Signal Format Select from the following when
"Interface Format" is set to "Quad-Link
3G/HD-SDI" or "Single-Link 12G/6G-
SDI."
 Auto (Default value)
 422 YCbCr 10bit
 444 RGB 10bit
 444 YCbCr 10bit
444 RGB 12bit

 444 YCbCr 12bit
 444 XYZ 12bit
"422 YCbCr 10bit" is set when
"Interface Format" is set to "Dual-Link
3G-SDI."
RGB Range Auto Select how to set the RGB Range.
 On: Use the RGB Range according to
Off: Use the RGB Range that was set

, SDI IN , SDI IN , and SDI
IN  with Quad Link. (Default
value)
and SDI IN  with Dual Link.
and SDI IN  with Dual Link.
: Select to use SDI 2 IN 
1)
with Single Link.
: Select to use SDI 2 IN 
1)
with Single Link.
1)
(Default value)
sample Interleave system.
the Square system.
the input signal information.
(Default value)
in "RGB Range."
Submenu Setting
RGB Range Select from the following when "RGB
Range Auto" is set to "Off" and the
RGB signal is input.



1) This manual regards the Full Range
EOTF Auto Select how to set EOTF when "Signal
Format" is set to a setting other than
"444 XYZ 12bit."


EOTF Select the gamma from the following
when "EOTF Auto" is set to "Off."










When "ITU-R BT.2100(HLG)" is selected

When "Signal Format" is set to "Auto"
or "444 XYZ 12bit" and the XYZ signal is
input, the optimum setting for the XYZ
signal is fixed.
Col. Space/Mtx. Select how to set the color space and
Auto transfer matrix when "Signal Format" is
set to a setting other than "444 XYZ
12bit."


23
Full: 0 to 1023 (10bit) / 0 to 4095
(12bit)
Limited: 64 to 940 (10bit) / 256 to
3760 (12bit)
1)
SDI Full Range : 4 to 1019 (10bit) /
16 to 4076 (12bit)
signals that are scaled to the
quantized value except the inhibit
code on the SDI standard as the SDI
Full Range.
On: Use EOTF according to the input
signal information. When the
value of SDI Payload ID Transfer
characteristics is Unspecified,
EOTF that was set in "EOTF" is
applied.
Off: Use EOTF that was set in "EOTF."
2.2
2.4
2.6
CRT
2.4(HDR)
S-Log3(HDR)
S-Log2(HDR)
SMPTE ST 2084(HDR)
ITU-R BT.2100(HLG)
S-Log3(Live HDR)
HLG System Gamma: Sets the
system gamma of the HLG. Set
from 1.000 to 1.500. (Default
value: 1.200)
Note
On: Use the color space and transfer
matrix according to the input
signal information.
Off: Use the color space and transfer
matrix that was set in the menu.