Electrical Installation; Cables General; Preparing Gland Plates For Cables - Danfoss VLT AQUA Drive FC 202 Design Manual

How to Install
Illustration 5.38 Frame Size F8
37,2
5 5
[ 1.47 ]
535,0
[ 21 . 06 ]
37.2
[1.47]
36.5
[1.44]
Illustration 5.39 Frame Size F9
70 . 0 593 . 0
[ 2.756 ] [ 23 . 346 ]
535 . 0
[ 21 . 063 ]
36 . 5
37 . 2
[ 1 . 437 ] 733 . 0
[ 1 . 466 ]
Illustration 5.40 Frame Size F10
70 . 0
593 . 0
[ 2.756 ]
[ 23 . 346 ]
535 . 0
[ 21 . 0631 ]
37 . 2
[ 1 . 466 ]
733 . 0
36 . 5
[ 28 . 858 ]
[ 1 . 437 ]
Illustration 5.41 Frame Size F11
100
70.0 593.0
1
[ 2.756 ] [ 23.326 ]
199.5
[ 7.854 ]
535.0
21.063 ]
258.5
[10.177 ]
35.5
[ 1 ] 36.5 733.0
[ 28.858 ]
[ 1.437 ]
673,0 593,0
[ 26.50 ] [ 23.35 ]
460,0
[ 18.11 ]
533,0
[ 20.98 ]
603,0
[ 23.74 ]
1336,0
[ 52.60 ]
1
[ 28 . 858 ] 800 . 0
[ 31. 496 ]
1533 . 0
[ 60 . 354 ]
1670 . 0 593 . 0
[ 65 . 748 ] [ 23 . 346 ]
870 . 7
593 . 0
[ 34 . 252 ]
[ 23 . 346 ]
800 . 0
[ 31. 496 ] 1533 . 0
[ 60 . 354 ]
1600 . 0
[ 62 . 992 ]
2333 . 0
[ 91 . 850 ]
MG20Z102 - VLT
®
VLT AQUA Drive FC 202 Design Guide
70 . 0
[ 2.756 ]
535 . 0
[ 21 . 063 ]
37 . 2
[ 1 . 466 ]
Illustration 5.42 Frame Size F12
1
70 . 0
199,5 [ 2.756 ]
[ 7.85 ]
535 . 0
258,5 [ 21 . 0631 ]
[ 10.18 ]
37 . 2
[ 1 . 466 ]
36 . 5
[ 1 . 437 ]
Illustration 5.43 Frame Size F13
1 Place conduits in marked areas
Table 5.8 Legend to Illustration 5.38-Illustration 5.43
199 . 5
[ 7 . 854 ]

5.3 Electrical Installation

258 . 5
[ 10 . 177 ]

5.3.1 Cables General

NOTE
Always comply with national and local regulations on
cable cross-sections.
For more information on the correct torques, see
1
Table 5.12.

5.3.2 Preparing Gland Plates for Cables

199 . 5
[ 7 . 854 ]
258 . 5
[ 10 . 177 ]
1.
2.
3.
4.
®
is a registered Danfoss trademark
857 . 7 994 . 3
[ 33 . 768 ] [ 39 . 146 ]
593 . 0
[ 23 . 346 ]
36 . 5
[ 1 . 437 ] 733 . 0
[ 28 . 858 ] 800 . 0
[ 32 ] 1933 . 0
[ 76 ]
1657 . 7
[ 65 . 2641 ]
870 . 7
593 . 0
[ 34 . 252 ]
593 . 0 [ 23 . 346 ]
[ 23 . 346 ]
733 . 0
[ 28 . 858 ] 800 . 0
[ 31. 496 ] 1533 . 0
[ 60 . 354 ] 1600 . 0
[ 62 . 992 ]
2733 . 0
[ 107 . 598 ]
Remove gland plate from the frequency
converter. (Avoiding foreign parts falling into the
frequency converter when removing knockouts).
Provide support for the gland plate around the
hole being punched or drilled.
Remove debris from the hole.
Mount the cable entry on the frequency
converter.
1
199 . 5
[ 7 . 854 ]
258 . 5
[ 10 . 177 ]
994 . 3
[ 39 . 146 ]
1
199 . 5
[ 7 . 854 ]
258 . 5
[ 10 . 177 ]