Page 1
User Manual UTC-315 Intel® Platform Processor- based Ubiquitous Touch Computer with 15.6” TFT LCD...
Page 2
No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd. Information provided in this manual is intended to be accurate and reliable. How- ever, Advantech Co., Ltd.
Page 3
Declaration of Conformity FCC Class A Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installa- tion.
Page 4
If any of these items are missing or damaged, contact your distributor or sales repre- sentative immediately. Technical Support and Assistance Visit the Advantech web site at http://support.advantech.com where you can find the latest information about the product. Contact your distributor, sales representative, or Advantech's customer service center for technical support if you need additional assistance.
Page 5
The sound pressure level at the operator's position according to IEC 704-1:1982 is no more than 70 dB (A). DISCLAIMER: This set of instructions is given according to IEC 704-1. Advantech disclaims all responsibility for the accuracy of any statements contained herein.
Contents Chapter General Information ......1 Introduction ....................2 General Specifications ................2 1.2.1 General ..................2 1.2.2 Standard PC Functions..............2 1.2.3 Audio Function ................2 1.2.4 LAN Function ................2 1.2.5 Touch Screen (Optional)............... 3 1.2.6 Environment.................. 3 LCD Specifications..................4 Optional modules ..................
Page 8
Table 4.3: JP1(D),JP3(EF):LCD POWER ......... 24 Table 4.4: JP3(D),JP6(E),JP5(F),JP4(G):Clear CMOS..... 24 Table 4.5: JP4(D),JP5(EG),JP7(F):AT/ATX POWER SEL..25 Table 4.6: CN17(D):COM1 Ring ..........25 Table 4.7: CN9(EF),CN14(G):COM1,COM2 Ring..... 25 Table 4.8: JCASH1: CASH DRAWER POWER SEL ....26 Table 4.9: CN10: CSAFE Power ..........26 Appendix A I/O Pin Assignments ......
Chapter General Information This chapter gives background information on the UTC-315. Sections include: Introduction General Specifications LCD Specifications Dimensions...
1.1 Introduction UTC-315x is a multi-purpose all-in-one computing system equipped with a wide for- mat, touch based LCD panel. It is easy to integrate key peripherals and display sys- tems for diversified self-service and interactive signage deployed in different locations. With the removable frame, the system could also fulfill control system applications with its panel mounting design.
Chapter System Setup This chapter details system setup on the UTC-315. Sections include: A Quick Tour of the UTC-315 Installation procedures Running the BIOS Setup Program Installing System Software...
2.1 A Quick Tour of the UTC-315 Before you start to set up the UTC-315, take a moment to become familiar with the locations and purposes of the controls, drives, connectors and ports, which are illus- trated in the figures below. When you place the UTC-315 upright on the desktop, its front panel appears as shown in Figure 2.1.
A. COM Port B. Line-out C. MIC-IN D. Gigabit LAN x2 E. HDMI F. USB3.0 x 4/ USB 2.0 x 2 (UTC-315E/F/G) G. RJ11 USB3.0 x 1/ USB 2.0 x 5 (UTC-315D) I. DC-IN H. Power switch 2.2 Installation Procedures 2.2.1 Connecting the power cord The UTC-315 can be powered by a DC electrical outlet.
2.3 Running the BIOS Setup Program Your UTC-315 is likely to have been properly set up and configured by your dealer prior to delivery. You may still find it necessary to use the UTC-315's BIOS (Basic Input-Output System) setup program to change system configuration information, such as the current date and time or your type of hard drive.
Page 19
Select Serial Port 2 Configuration. Change Serial Port 2 Mode [RS232/RS422/RS485]. UTC-315 User Manual...
Advantech website. Note! The drivers and utilities used for the UTC-315 are subject to change without notice. If in doubt, check Advantech's website or contact our application engi- neers for the latest information regarding drivers and utilities. UTC-315 User Manual...
Chapter Hardware Installation and Upgrades This chapter details installing the UTC-315 hardware. Sections include: Overview of Hardware Installa- tion and Upgrading Installing the 2.5" Hard Disk Drive (HDD) Installing the mSATA Installing the WLAN...
3.1 Introduction The UTC-315 consists of a PC-based computer that is housed in an plastic enclo- sure. You can install a HDD, DRAM, and MiniSATA card by removing the rear cover. Any maintenance or hardware upgrades can be easily completed after removing the rear cover.
3.3 Installing the mSATA Card Remove 10 screws on the back cover. Remove 6 screws on the reinforced board. Figure 3.2 Installing the mSATA Card UTC-315 User Manual...
Reserve two locations for the external Antenna. One is at the IO port, the other is at the rear cover. Customers can choose based on their requirement. Remove 10 x screws from the back cover. Remove 6 screws on the reinforced board. Coaxial cable (Advantech P/N: 1750008953-01 (for UTC-315D/E/F), 1750008954-01 (for UTC-315G)) UTC-315 User Manual...
Page 25
Connect the coaxial cable to "ANT1" on the WLAN card. Install the WLAN card on M/B bottom side. Cable routing of the wireless antenna is shown below. UTC-315 User Manual...
Chapter Jumper and Connector Settings This chapter details instructions for setting jumpers and connect- ing peripherals, switches, and indicators. Jumpers and Connectors CMOS Clear for External RTC (JP3) COM Port Interface Watchdog Timer Configuration...
4.1 Jumpers and Connectors 4.1.1 Setting Jumpers Users can configure the UTC-315 to match their application needs by setting jump- ers. A jumper is the simplest type of electrical switch and consists of two metal pins and a small metal clip (typically protected by a plastic cover) that slides over the pins to connect them.
4.2 Jumpers 4.2.1 Jumper List Table 4.2: Jumper List JP1(D),JP3(EF) LCD POWER JP3(D),JP6(E),JP5(F),JP4(G) Clear CMOS JP4(D),JP5(EG),JP7(F) AT/ATX POWER SEL CN17(D),CN9(EF),CN14(G) COM1,COM2 RING JCASH1 Cash drawer power CN10(E) CSAFE POWER 4.2.2 Jumper Settings Table 4.3: JP1(D),JP3(EF):LCD POWER Part Number 1653003100 Footprint HD_3x1P_100_D Description PIN HEADER 3x1P 2.54mm 180D(M) DIP 205-1x3GS...
Table 4.5: JP4(D),JP5(EG),JP7(F):AT/ATX POWER SEL Part Number 1653003101 Footprint HD_3x1P_79_D Description PIN HEADER 3*1P 180D(M) 2.0mm DIP SQUARE W/O Pb Setting Function (1-2) (2-3)* Table 4.6: CN17(D):COM1 Ring Part Number 1653005101 Footprint HD_5x1P_79_D Description PIN HEADER 5x1P 2.0mm 180D(M) DIP 1140-000-05SN Setting Function (1-2)
Table A.9: CN7(D),CN3(EFG):SATA POWER Part Number 1659254005 Footprint SATA_7P_WATM-07DBN4A3B8UW_D Description Serial ATA 7P 1.27mm 180D(M) DIP WATM-07DBN4A3B8 Pin name +3.3V +12V Table A.10: CN8(D),CN5(G):Internal USB Part Number 1655000453 Footprint WHL5V-2M-24W1140 Description WAFER BOX 2.0mm 5P 180D(M) DIP WO/Pb JIH VEI Pin name UTC-315 User Manual...
Table A.11: CN9(D),CN6(EG),CN26(F):Touch Part Number 1655005110 Footprint WF_5P_100_RA_D Description WAFER 5P 2.54mm 90D(M) DIP 2542-WR-5 Pin name SENSE Table A.12: CN13(DEG):DDR3L SODIMM Part Number 1651002087-11 Footprint DDR3_204P_AS0A626-N2S6-7H Description DDR3 SODIMM H=5.2mm STD 204P SMD AS0A626-H2S6-7H Pin name Table A.13: DIMM(F)DDR4 SODIMM Part Number 1651002829-01 Footprint...
Table A.15: MSATA1(DEFG):MSATA Part Number 1654002538 Footprint FOX_AS0B226-S68K7F Description MINI PCI E 52P 6.8mm 90D SMD AS0B226-S68Q-7H Pin name +3.3V SATA1_RX+ +3.3V SATA1_RX- SATA1_TX- SATA1_TX+ +3.3V +3.3V UTC-315 User Manual...
Table A.25: CN19(EF),CN21(G):External USB Part Number 1654010969-01 Footprint USB_9x2P_UEA1112C-8HS6-4F Description USB CONN. 18P 2.0mm 90D(F) DIP UEA1112C Pin name RX_D- RX_D+ TX_D- TX_D+ RX_D- RX_D+ TX_D- TX_D+ UTC-315 User Manual...
Table A.26: CN20(EF),CN22(G):External USB Part Number 1654010969-01 Footprint USB_9x2P_UEA1112C-8HS6-4F Description USB CONN. 18P 2.0mm 90D(F) DIP UEA1112C Pin name RX_D- RX_D+ TX_D- TX_D+ RX_D- RX_D+ TX_D- TX_D+ UTC-315 User Manual...
Table A.27: CN24,CN25 (D),CN18(EF),CN20(G):External USB Part Number 1654009513 Footprint USB_8P_UB1112C-8FDE-4F Description USB CONN. 8P 2.0mm 90D DIP UB1112C-8FDE-4F Pin name +5VSB +5VSB UTC-315 User Manual...
Table A.28: CN26(D):External USB Part Number 1654010199 Footprint USB_13P_UEA1112C-UHS6-4F Description USB Conn. 2.0+3.0 13P 90D(F) DIP UEA1112C-UHS6-4 Pin name +5VSB RX_D- RX_D+ TX_D- TX_D+ +5VSB UTC-315 User Manual...
Table A.29: CN27(D),CN21(E),CN22(F),CN25(G):Line-out Part Number 1652001586 Footprint KUONYI_PJ-2508PC-5-L Description PHONE JACK 5P 3.5φ 90D(F) AZALIA GREEN DIP WO/P Pin name OUT_L OUT_R Table A.30: CN28(D),CN22(E),CN21(F),CN24(G):MIC-IN Part Number 1652001584 Footprint KUONYI_PJ-2508PA-5-L Description PHONE JACK 5P 3.5φ 90D(F) AZALIA PINK DIP WO/Pb Pin name MIC_L MIC_R...
Table A.32: CN31(DG),CN25(EF):DC-IN Part Number 1652005624 Footprint PJ_2P_2DC-G213B200 Description DC POWER JACK 2.5mm 90D(M) DIP 2DC-G213B200 Pin name DC_IN Table A.33: CN29(D),CN23(EF),CN26(G) RJ11 Part Number 1652005977-02 Footprint S RJ11_6P_RJ1201-66N024R0 Description PHONE JACK RJ11 6P6C 90D(F) DIP 6u RJ1201-66N024 Pin name Drawer_A Drawer_state Power...
Table A.34: Power button Part Number 1600000055 Footprint SW_6P_TC003-N11AABRGXX-RK_D Description PUSH SW DIP 6P W/LED WO/Pb TC003-N11AABRGXX-RK Pin name ATX_PWRBTN# ATX_PWRBTN# UTC-315 User Manual...
Need help?
Do you have a question about the UTC-315 Series and is the answer not in the manual?
Questions and answers