Trimming Sub Clips - Sony XDCAM PDW-1500 Operation Manual

5-2-3 Trimming Sub Clips

SG DATA SG DATA SG DATA SG DATA
ACCESS
ANA SDI ANA SDI ANA SDI ANA SDI INPUT
AE8/EBU AE8/EBU AE8/EBU AE8/EBU
i.LINK
dB OVER dB OVER dB OVER dB OVER
0 0 0 0 SDI
CMPST
NETWORK -12 -12 -12 -12 Y-R,B
LOCAL -20 -20 -20 -20 SG
REMOTE
-30 -30 -30 -30 HOURS
MONITOR
-40 -40 -40 -40
MONITOR 1/2 3/4
-60 -60 -60 -60
CH- 15 CH- 26 CH- 37 CH- 48 5/6 7/8 4 8 CH
L
MIX
AUDIO
R VIDEO
MONITOR SEL METER SEL INPUT CH INPUT SEL INPUT SEL
ALL/CH-1 CH-2 CH-3
VARIABLE
REC
PRESET
PB
PHONES
PREV PLAY NEXT STOP
F REV F FWD
TOP END
NEXT button
PREV button
1
Carry out steps 1 to 4 of 5-2-2 "Reordering Sub Clips"
to select a sub clip and display the sub clip operation
menu.
2
Use the F or f button to select TRIM, and then press
the SET button.
The first frame of the selected sub clip appears.
In this state, you can play back and search the entire
disc.
To cancel the trim and return to the previous
screen
With the SHIFT button held down, press the SET
button.
3
Play back and search the disc to find scenes to set new
In and Out points.
72
5-2 Creating Clip Lists
THUMBNAIL button
SET button
SHIFT button
RESET button
EJECT
REMOTE [9P iLINK]
EDIT KEY INH ALARM
VITC VIUB COUNTER VITC REC INH
MINUTES SECONDS FRAMES
AUDIO 625 IMX[50 40 30]
18 24 BIT 525 DVCAM
SHIFT
COUNTER SYS MENU
SELECT HOLD MENU
SUB THUMB
CH-4
CLIP NAIL SET RESET
CLIP ESSENCE S.SEL
MENU MARK MARK1
REC
IN OUT
MARK2
Jog dial
g/OUT button
F/f buttons
G/IN button
4
At the scene where you want to set a new In or Out
point, hold down the G/IN button (to change the In
point) or the g/OUT button (to change the Out point)
and press the SET button.
Depending on the button that you pressed, a new In or
Out point is set, and the IN or OUT indicator lights.
To change both the In and Out points
Carry out steps 3 and 4 for both the In and Out points.
To reset the In or Out point
With the G/IN button or g/OUT button held down,
press the RESET button. The In or Out point is
restored to the value it had before the sub clip trim
screen opened.
To cue up the In or Out point
With the G/IN button held down, press the PREV
button. Or with the the g/OUT button held down, press
the NEXT button.
Note
You can escape from the sub clip trim screen to full-
screen display without executing a trim if you press the
THUMBNAIL button.
5
Once you have set the new In point or Out point, hold
down the SHIFT button and press the SET button.
The trim is executed, and you return to the sub clip
thumbnail display.
To cancel the trim
Reset the In or Out point to the value it had before you
entered the sub clip trim screen, and then hold down
the SHIFT button and press the SET button.
6
Save the current clip list to disc.
See 5-2-6 "Saving the Current Clip List to Disc" (page
73).