Sony XDCAM PDW-1500 Operation Manual page 127

SG DATA SG DATA SG DATA SG DATA
ACCESS EDIT
ANA SDI ANA SDI ANA SDI ANA SDI
INPUT
AE8/EBU AE8/EBU AE8/EBU AE8/EBU VITC
i.LINK
dB dB dB dB
OVER OVER OVER OVER
0 0 0 0 SDI
CMPST
NETWORK -12 -12 -12 -12 Y-R,B
LOCAL -20 -20 -20 -20 SG
REMOTE -30 -30 -30 -30 HOURS
-40 -40 -40 -40 MONITOR
MONITOR 1/2 3/4
-60 -60 -60 -60 AUDIO
CH- 15 CH- 26 CH- 37 CH- 48 5/6 7/8 4 8 CH
L
MIX
R AUDIO VIDEO
MONITOR SEL METER SEL INPUT CH INPUT SEL INPUT SEL
ALL/CH-1 CH-2 CH-3 CH-4
VARIABLE
REC
PRESET
PB
PHONES
PREV PLAY NEXT
STOP
F REV F FWD
TOP END
2
1
Using the F/f buttons, display the desired setting.
2
Press the SET button.
This saves the new setting, and the menu disappears
from the time data display.
To cancel changing a setting
Before pressing the SET button, press the MENU
button.
The menu disappears from the time data display,
without saving the new setting.
To change network settings
To change network settings, carry out steps 1 to 3 in the
item, "To display a menu item setting" above, to display
the NETWORK CONFIG menu item, then carry out the
following operations.
For details of the settings, consult your network
administrator.
When the IP address is assigned automatically
Check that the network cable is connected to this unit
before carrying out the operation.
SG DATA SG DATA SG DATA SG DATA REMOTE [9P iLINK]
ACCESS EDIT
ANA SDI ANA SDI ANA SDI ANA SDI
INPUT
AE8/EBU AE8/EBU AE8/EBU AE8/EBU VITC VIUB
i.LINK
dB dB dB dB
OVER OVER OVER OVER
0 0 0 0 SDI
CMPST
NETWORK -12 -12 -12 -12 Y-R,B
LOCAL -20 -20 -20 -20 SG
REMOTE -30 -30 -30 -30 HOURS
-40 -40 -40 -40 MONITOR
MONITOR 1/2 3/4
-60 -60 -60 -60 AUDIO
CH- 15 CH- 26 CH- 37 CH- 48 5/6 7/8 4 8 CH
L
MIX
R AUDIO VIDEO
MONITOR SEL METER SEL INPUT CH INPUT SEL INPUT SEL
ALL/CH-1 CH-2 CH-3 CH-4
VARIABLE
REC
PRESET
PB
PHONES
PREV PLAY NEXT
STOP
F REV F FWD
TOP END
4
1
Using the F/f buttons, display ">DHCP."
EJECT
REMOTE [9P iLINK]
KEY INH ALARM
VIUB COUNTER VITC REC INH
MINUTES SECONDS FRAMES
625 IMX[50 40 30]
18 24 BIT 525 DVCAM
SHIFT
COUNTER SYS MENU
SELECT HOLD MENU
SUB THUMB
CLIP NAIL SET RESET
CLIP ESSENCE S.SEL
MARK1
MENU MARK
REC
IN OUT
MARK2
1
EJECT
KEY INH ALARM
COUNTER VITC REC INH
MINUTES SECONDS FRAMES
625 IMX[50 40 30]
18 24 BIT 525 DVCAM
SHIFT
COUNTER SYS MENU
SELECT HOLD MENU
SUB THUMB
CLIP NAIL SET RESET
CLIP ESSENCE S.SEL
MARK1
MENU MARK
REC
IN OUT
MARK2
1,3 2
2
Press the g button.
3
Press the f button, to display ">> ENABLE."
4
Press the SET button.
To check the assigned IP address
In the NETWORK CONFIG menu, using the F/f
buttons, display ">IP address," then press the g
button.
Note
If the IP address cannot be assigned, this is shown as
"000.000.000.000." In this case, consult the network
administrator.
To set the IP address
First set DHCP to "DISABLE." (See the previous item,
"When the IP address is assigned automatically.")
SG DATA SG DATA SG DATA SG DATA EDIT
ACCESS
ANA SDI ANA SDI ANA SDI ANA SDI INPUT
AE8/EBU AE8/EBU AE8/EBU AE8/EBU VITC
i.LINK
dB OVER dB OVER dB OVER dB OVER
SDI
0 0 0 0
CMPST
NETWORK
-12 -12 -12 -12 Y-R,B
SG
LOCAL -20 -20 -20 -20
REMOTE HOURS
-30 -30 -30 -30
-40 -40 -40 -40 MONITOR
MONITOR 1/2 3/4 AUDIO
-60 -60 -60 -60
15 26 37 48
CH- CH- CH- CH- 5/6 7/8 4 8 CH
L
MIX
AUDIO VIDEO
R
MONITOR SEL METER SEL INPUT CH INPUT SEL INPUT SEL
ALL/CH-1 CH-2 CH-3 CH-4
VARIABLE
REC
PRESET
PB
PHONES
PREV PLAY NEXT STOP
TOP F REV F FWD END
4
1
Using the F/f buttons, display ">IP address."
2
Press the g button.
The IP address appears, and the digit that can be
changed flashes.
Flashes to indicate that the digit can be changed.
3
Set the IP address.
To select a different digit to be changed
Use the G/g buttons.
To change the value of a digit
Turn the jog dial or shuttle dial.
EJECT
REMOTE [9P iLINK] KEY INH
ALARM
VIUB COUNTER VITC REC INH
MINUTES SECONDS FRAMES
625 IMX[50 40 30]
18 24 BIT 525 DVCAM
COUNTER SYS MENU SHIFT
SELECT HOLD MENU
SUB THUMB
CLIP NAIL SET RESET
CLIP ESSENCE S.SEL
MENU MARK MARK1
REC
IN OUT
MARK2
1 2,3 3
8-4 Maintenance Menu
127