Rear Panel - Sony XDCAM PDW-1500 Operation Manual

2-2 Rear Panel

1 REF. VIDEO IN connectors
1 Analog audio signal inputs/
outputs (see page 28)
S400 (i.LINK) connector
2
3 REMOTE connector
4 (network) connector
2 Digital audio signal inputs/outputs
(see page 28)
a REF. VIDEO IN (reference video signal input)
connectors (BNC type)
The two connectors form a loop-through connection; when
a reference video signal is input to the left connector, the
same signal is input from the right connector (
connected device. When no connection is made to the right
connector, the left connector is automatically terminated
with an impedance of 75 ohms.
b
S400 (i.LINK) connector (6-pin, IEEE1394
compliant)
Connect a DV device, computer, or similar, using an
i.LINK cable.
When the unit is shipped from the factory, the audio output
signal is set to 16 bit/48 kHz/2ch mode. You can change
the audio mode and output channel settings with extended
menu item 831 "DV OUT AUDIO MODE" and extended
menu item 828 "SDI/DV AUDIO OUTPUT SELECT."
See 8-3-2 "Extended Menu Operations" (page 120) for
more information about how to make these settings.
Notes
• If video or audio signals from an external device
connected with the S400 (i.LINK) connector are not
output, disconnect the i.LINK cable and connect it again,
pushing it straight in.
• When the PDW-1500 is connected to a device with a 6-
pin i.LINK connector by an i.LINK cable, before
unplugging the i.LINK cable, first power off the device
and disconnect the power plug from the outlet. If the
i.LINK cable is unplugged with the device power plug
still connected, a current from an excessive voltage (8 to
REF.VIDEO IN
AUDIO IN 1/3 2/4 AUDIO OUT
DIGITAL AUDIO (AES/EBU) SDI
IN 1/2 3/4 OUT 1/2 3/4 IN OUT 1 2 (SUPER)
S400
REMOTE
40 V) output from the i.LINK connector of the device
flows into the PDW-1500. This may cause a failure of
the PDW-1500.
• When connecting the PDW-1500 to a device with a 6-pin
) to a i.LINK connector, connect to the 6-pin i.LINK
connector of the other device first.
• Except in playback mode (jog and shuttle modes, etc.), if
you are monitoring the audio signal output from this
connector on another device, the audio signal may sound
differently from the audio signal played back on the
PDW-1500.
c REMOTE (remote control signal) connector (D-
sub 9-pin)
To control the PDW-1500 from a controller or VTR
supporting the RS-422A Sony 9-pin VTR protocol,
connect the device to this connector.
d
This is a 10Base-T/100Base-TX/1000Base-T connector
for network connection.
CAUTION
For safety, do not connect the connector for peripheral
device wiring that might have excessive voltage to this
port. Follow the instructions in this manual when making
connections.
ATTENTION
Par mesure de sécurité, ne raccordez pas le connecteur
pour le câblage de périphériques pouvant avoir une tension
excessive à ce port. Suivez les instructions pour ce port.
VIDEO IN VIDEO OUT
3Analog video signal inputs/
1 2
(SUPER)
outputs (see page 28)
1/3 2/4 AUDIO
MONITOR OUT
5 AUDIO MONITOR OUT connector
TIME CODE
4Time code inputs/outputs
IN OUT
(see page 29)
5 Power supply section
(see page 29)
6 SDI signal inputs/
outputs (see page 29)
(network) connector (RJ-45 type)
27
2-2 Rear Panel