Metso neles ND7000H Operating Instructions Manual page 68

68
Advanced Configuration
1 Flow Modification
2 Status Configuration
3 HART Configuration
4 HART Burst Mode Configuration
5 Reset
6 Write Protection
Fig 2 ND9000H 0402 Menu Tree
Europe, Vanha Porvoontie 229, P.O. Box 304, FI-01301 Vantaa, Finland. Tel. +358 20 483 150. Fax +358 20 483 151
North America, 44 Bowditch Drive, P.O. Box 8044, Shrewsbury, M A 01545, USA. Tel. +1 508 852 0200. Fax +1 508 852 8172
South America, Av. Independéncia, 2500-Iporanga, 18087-101, Sorocaba-São Paulo, Brazil. Tel. +55 15 2102 9700. Fax +55 15 2102 9748
Asia Pacific, 238B Thomson Road, #17-01 Novena Square Tower B, Singapore 307685. Tel. +65 6511 1011. Fax +65 6250 0830
China, 11/F, China Youth Plaza, No.19 North Rd of East 3rd Ring Rd, Chaoyang District, Beijing 100020, China. Tel. +86 10 6566 6600. Fax +86 10 6566 2583
Middle East, Roundabout 8, Unit AB-07, P.O. Box 17175, Jebel Ali Freezone, Dubai, United Arab Emirates. Tel. +971 4 883 6974. Fax +971 4 883 6836
Flow Modification
1 Characterization Type
2 Shape Factor
3 Init Table with Predefined Curves
4 User Defined Curve
Status Configuration
1 Manage All Statuses
2 Reduced Performance
3 Calibration Recommended
4 Valve Position Low Limt Exceeded
5 Valve Position High Limit Exceeded
6 Pressure Sensor 1 Failure Detected
7 Pressure Sensor 2 Failure Detected
8 Pressure Sensor 3 Failure Detected
9 Spool Valve Sensor Failure Detected
Temperature Sensor Failure Detected
Continued Processor Reset Detected
Position Sensor Failure Detected
Position Sensor Out of Range Detected
Input Signal Sensor Failure Detected
Prestage Shortcut Detected
Prestage Cut Detected
Steady State Deviation Trend Limit Exceeded
Dynamic State Deviation Limit Exceeded
Stiction Trend Low Limit Exceeded
Stiction Trend High Limit Exceeded
Load for Opening Trend Low Limit Exceeded
Load for Opening Trend High Limit Exceeded
Total Operation Time Limit Exceeded
Total Valve Travel Limit Exceeded
Total Valve Reversals Limit Exceeded
Total Actuator Travel Limit Exceeded
Total Acuator Reversals Limit Exceeded
Total Spool Valve Travel Limit Exceeded
Total Spool Valve Reversals Limit Exceeded
Daily Setpoint Reversals Trend Limit Exceeded
Daily Valve Reversals Trend Limit Exceeded
Daily Valve Reversals while Stable Setpoint Trend Limit Exceeded
Supply Pressure Limit Exceeded
Temperature Limit Exceeded
Hunting Detected
Steady State Deviation Limit Exceeded
Stiction Low Limit Exceeded
Stiction High Limit Exceeded
Load for Opening Low Limit Exceeded
Load for Opening High Limit Exceeded
Spool Valve Problem Detected
Pneumatics Problem Detected
Friction Problem Detected
Supply Pressure Too Low for Single Acting Actuator.
Hart Configuration
1 Preambles
2 Dynamic Variables
3 Pressure Unit
4 Temperature Unit
HART Burst Mode Configuration
1 Burst Mode Variables
Reset
Valve Travel and Reversals; Actuator Travel and Reversals; Setpoint Travel and Reversals; Spool Valve Travel and Reversals; Trends;
1 Reset Statistics
2 Reset Configuration Changed Flag
Write Protection
1 Device is locked
2 Lock is permanent
3 Locked by a primary master
4 Lock/Unlock Device
Metso Flow Control Inc.
www.metso.com/valves
Shape Factor, Custom Table, Linear(not used)
<1.0 = quick opening, 1.0 = linear, >1.0 = equal percent
Linear, 1/25, Quick 1/25, 1/33, Quick 1/33, 1/50, Quick 1/50
0.100% defined in 5% increments
Manage All Statuses
Enable All Statuses
ON Disable All Statuses
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
Preambles
1 Num resp preams
bar, PSI Dynamic Variables
Celsius, Fahrenheit 1 1st Dyn Var
2 2nd Dyn Var
3 3rd Dyn Var
4 4st Dyn Var
Burst Mode Variables
1 Burst Mode
2 Burst Command
3 1st Burst Var.
4 2nd Burst Var.
5 3rd Burst Var.
6 4th Burst Var.
Valve Travel Histogram; Event Log; Reset All
No, Yes
OFF
OFF
OFF
Unlock, Lock Temporarily, Lock Permanently
7 ND90 71 en
5
Off
Cmd 3: Dyn vars/current
Setpoint
Valve Position
Device Temperature
Actuator Pressure Difference