the Owner’s Information, that may or may not be urged to read these publications carefully. Fol- INTRODUCTION applicable to your vehicle, will be identified with lowing the instructions and recommendations in Dear Customer, the wording “If Equipped”. All data contained in this Owner’s Manual will help assure safe and Congratulations on selecting your new vehicle.
an officially approved design), or if an individual HOW TO USE THIS MANUAL VEHICLE MODIFICATIONS/ operating permit was issued for the vehicle after ALTERATIONS the attachment or installation of such parts, it Essential Information cannot be implicitly assumed that the driving Consult the Table of Contents to determine which safety of your vehicle is unimpaired.
Page 7
WARNING! To prevent SERIOUS INJURY or DEATH: • ALWAYS remove any “Track-Use” equip- ment before driving on public roads. • ALWAYS properly use your three-point seat belts when driving on public roads. • In a collision, you and your passengers can suffer much greater injuries if you are not properly buckled up.
KEYS To remove the emergency key, slide the me- chanical release button on the back of the key fob sideways with your thumb and then pull the Key Fob key out with your other hand. Your vehicle uses a keyless ignition system. The ignition system consists of a key fob with Re- mote Keyless Entry (RKE) and a START/STOP push button ignition system.
Page 19
To Unlock The Doors 1st Press Of Key Fob Unlocks The turn signal lights will flash and the horn will Push and release the unlock button on the key This feature lets you program the system to chirp to acknowledge the signal if programmed. fob once to unlock the driver’s door or twice unlock either the driver’s door or all doors on the Refer to “Uconnect Settings”...
Page 20
1. Remove the emergency key by sliding the mechanical latch on the back of the key fob sideways with your thumb and then pull the emergency key out with your other hand. Emergency Key Removal Separating Case With A Key Blade Emergency Key Removal 1 —...
Programming Additional Key Fobs NOTE: Programming the key fob may be performed by When having the Sentry Key Immobilizer Sys- an authorized dealer. tem serviced, bring all vehicle keys with you to an authorized dealer. NOTE: Once a key fob is programmed to a vehicle, it IGNITION SWITCH cannot be repurposed and reprogrammed to another vehicle.
START CAUTION! • The engine will start. An unlocked vehicle is an invitation for thieves. Always remove key fob from the WARNING! vehicle and lock all doors when leaving the • When exiting the vehicle, always remove vehicle unattended. the key fob from the vehicle and lock your vehicle.
NOTE: WARNING! (Continued) CAUTION! • With remote start, the engine will only run for brake, place the engine in the OFF posi- An unlocked vehicle is an invitation for 15 minutes (timeout) unless the ignition is tion, remove the key fob from the vehicle thieves.
NOTE: To Enter Remote Start Mode WARNING! Push and release the remote start button on the To avoid unintentional shutdowns, the system • Do not start or run an engine in a closed key fob twice within five seconds. The vehicle will disable with a one time push of the remote garage or confined area.
The system uses a key fob, keyless push button To Cancel Remote Start CAUTION! (Continued) ignition and a RF receiver to prevent unauthor- Remote Starting will also cancel if any of the result in vehicle starting problems and loss of ized vehicle operation.
• Push the Keyless Enter-N-Go ignition button NOTE: 2. Perform one of the following methods to lock (requires at least one valid key fob in the Duplication of key fobs may be performed at an the vehicle: vehicle). authorized dealer. This procedure consists of •...
between cycles, up to eight cycles if the trigger Power Door Locks WARNING! remains active and the vehicle security alarm A power door lock switch is on each front door • For personal security and safety in the will rearm itself. trim panel.
Keyless Enter-N-Go — Passive Entry automatically. The interior door panel lock knob Driver Door 1st Press” or “Unlock All Doors 1st will raise when the door is unlocked. The Passive Entry system is an enhancement to Press”). the vehicle’s Remote Keyless Entry system and Preventing Inadvertent Locking Of Passive a feature of Keyless Enter-N-Go.
is detected outside the vehicle. The vehicle will NOTE: not unlock the doors when any of the following If you inadvertently leave your vehicle’s Passive Entry key fob in the trunk and try to close the conditions are true: deck lid, the deck lid will automatically unlatch, •...
2. The vehicle was in motion, then speed re- To Engage Or Disengage The Child- NOTE: Protection Door Lock System turned to 0 mph (0 km/h) and the transmis- For emergency exit from the rear seats when the Child-Protection Door Lock System is en- sion is placed in PARK.
Manual Adjustment (Rear Seats) After releasing the seatback, it can be folded WARNING! forward. Folding Rear Seat • Be certain that the seatback is securely The rear seatbacks can be folded forward to locked into position. If the seatback is not provide an additional storage area.
Page 32
CAUTION! WARNING! • Adjusting a seat while driving may be dan- Do not place any article under a power seat gerous. Moving a seat while driving could or impede its ability to move as it may cause result in loss of control which could cause a damage to the seat controls.
NOTE: 2. Adjust all memory profile settings to desired Power Lumbar — If Equipped Vehicles equipped with power driver or passen- Your vehicle is equipped with two key fobs, one preferences (i.e., seat, side mirror, power tilt ger seats may also be equipped with power key fob can be linked to memory position 1 and and telescopic steering column [if equipped], lumbar.
Page 34
• When you cycle the vehicle’s ignition to the To program your key fobs, perform the following: Driver One Memory Position Recall OFF position, the driver seat will move about • To recall the memory settings for driver one 1. Cycle the vehicle’s ignition to the OFF posi- 2.4 inches (60 mm) rearward if the driver seat tion.
Heated Seats — If Equipped for LO. Turning the heating elements off will WARNING! return the user to the radio screen. On some models, the front and rear seats may • Persons who are unable to feel pain to the be equipped with heaters located in the seat •...
• Push the heated seat button a second Vehicles Equipped With Remote Start WARNING! (Continued) time to turn the LO setting on. On models that are equipped with remote start, that has been overheated could cause • Push the heated seat button a third time to the ventilated seats can be programmed to serious burns due to the increased surface...
NOTE: WARNING! (Continued) Do not reverse the head restraints (making the • Do not place items over the top of the rear of the head restraint face forward) in an Reactive Head Restraint, such as coats, attempt to gain additional clearance to the back seat covers or portable DVD players.
while pulling the head restraint up. To reinstall power tilt/telescoping steering column switch is the head restraint, put the head restraint posts located below the multifunction lever on the into the holes. Then, adjust it to the appropriate steering column. height.
Vehicles Equipped With Remote Start This mirror automatically adjusts for headlight WARNING! (Continued) glare from vehicles behind you. On models that are equipped with remote start, driving or driving with the steering column the heated steering wheel can be programmed NOTE: unlocked, could cause the driver to lose to come on during a remote start through the...
Driver’s Outside Automatic Dimming NOTE: CAUTION! The approach lighting will not function when the Mirror — If Equipped gear selector is moved out of the PARK position. To avoid damage to the mirror during clean- The driver’s outside mirror will automatically ing, never spray any cleaning solution di- adjust for glare from vehicles behind you.
Refer to “Driver Memory Seat” in “Getting To Automatic Folding Mirrors To reset the power folding mirrors, fold and Know Your Vehicle” for further information. unfold them by pushing the button (this may When the Automatic Folding Mirrors feature is require multiple button pushes).
Refer to “Uconnect Settings” in “Multimedia” for Headlight Switch further information. The headlight switch is located on the left side of the instrument panel. This switch controls the Illuminated Vanity Mirrors — If operation of the headlights, parking lights, in- Equipped strument panel lights, interior lights and fog lights.
toward you. This will cause the high beam NOTE: to the vehicle). Also, dirt, film, and other obstructions on the windshield or camera headlights to turn on, and remain on, until the If allowed, by law, in the country in which the lens will cause the system to function lever is released.
tion, the headlights will turn off when the wipers To activate the delay feature, place the ignition are turned off if they were turned on by this in the OFF position while the headlights are still feature. on. Then, turn off the headlights within 45 sec- onds.
Turn Signals INTERIOR LIGHTS Front Map/Reading Lights — If Equipped The front map/reading lights are mounted in the Move the multifunction lever up or down and the The interior lights come on when a door is overhead console. arrows on each side of the instrument cluster opened.
Page 46
Ambient Light — If Equipped With the parking lights or headlights on, rotating Parade Mode (Daytime Brightness Feature) The overhead console is equipped with an am- the left dimmer control upward will increase the Rotate the instrument panel dimmer control bient light feature.
If you activate the washer while the windshield WINDSHIELD WIPERS AND CAUTION! (Continued) wiper is turned off, the wipers will operate for WASHERS wiper control is left in any position other three wipe cycles and then turn off. The multifunction lever operates the windshield than off.
• Neutral Wipe Inhibit — The Rain Sensing Rain Sensing Wipers NOTE: feature will not operate when the ignition is This feature senses rain or snowfall on the • The Rain Sensing feature will not operate placed in the RUN position, the automatic windshield and automatically activates the wip- when the wiper speed is in the low or high transmission gear selector is in the NEU-...
Automatic Climate Control Overview Uconnect 4C/4C NAV Automatic Climate Controls...
Page 50
Automatic Climate Control Descriptions Icon Description MAX A/C Button Press and release to change the current setting, the indicator illuminates when MAX A/C is on. Performing this function again will cause the MAX A/C operation to switch into manual mode and the MAX A/C indicator will turn off. NOTE: The MAX A/C button is only available on the touchscreen.
Page 51
Icon Description Front Defrost Button Press and release to change the current airflow setting to Defrost mode. The indicator illuminates when this feature is on. Air comes from the windshield and side window demist outlets. When the defrost button is selected, the blower level may increase.
Page 52
Icon Description Faceplate Knob Blower Control Blower Control is used to regulate the amount of air forced through the climate system. There are seven blower speeds available. The speeds can be selected using either the blower control knob on the faceplate or the buttons on the touch- screen.
Icon Description Floor Mode Floor Mode Air comes from the floor outlets. A slight amount of air is directed through the defrost and side window demister outlets. Mix Mode Mix Mode Air is directed through the floor, defrost, and side window demister outlets. This setting works best in cold or snowy condi- tions that require extra heat to the windshield.
MAX A/C displayed, the system will achieve and auto- Operating Tips matically maintain that comfort level. MAX A/C sets the control for maximum cooling NOTE: performance. 3. When the system is set up for your comfort Refer to the chart at the end of this section for level, it is not necessary to change the set- suggested control settings for various weather Press and release to toggle between MAX A/C...
crease the front blower speed. Do not use the Cabin Air Filter WINDOWS Recirculation mode without A/C for long periods, The climate control system filters out dust and as fogging may occur. pollen from the air. Contact an authorized dealer Power Window Controls to service your cabin air filter, and to have it The window controls on the driver’s door control...
Page 56
Auto-Up Feature With Anti-Pinch Protection Reset Auto-Up WARNING! — If Equipped Should the Auto-Up feature stop working, the Never leave children unattended in a vehicle, Pull window up switch to second detent for at window may need to be reset. To reset Auto-Up: and do not let children play with power win- least a half of a second and the window will go 1.
controls and the rear sunscreen, push and re- COMMANDVIEW SUNROOF WARNING! (Continued) lease the window lockout button again (setting it WITH POWER SHADE — IF equipped with Keyless Enter-N-Go in the in the up position). EQUIPPED ACC or ON/RUN mode. Occupants, par- ticularly unattended children, can become The CommandView sunroof switch is located to the left between the sun visors on the overhead...
open automatically and stop at full open posi- Wind Buffeting Manual Open tion. During Express Open operation, any other Wind buffeting can be described as the percep- Push and hold the sunshade switch rearward, actuation of the sunroof switches will stop the tion of pressure on the ears or a helicopter-type the sunshade will open to the half open position sunroof in a partially open position.
Pinch Protect Feature HOOD This feature will detect an obstruction in the closing of the sunroof during the Express Close To Open The Hood operation. If an obstruction in the path of the Two latches must be released to open the hood. sunroof is detected, the sunroof will automati- 1.
of the decklid overhang. The release feature will Opening From Outside The Vehicle WARNING! function only when the vehicle is in the unlock To Unlock/Open The Trunk condition. Be sure the hood is fully latched before The trunk may be unlocked/opened using either driving your vehicle.
Closing WARNING! WARNING! With one or more hands placed on the outside • Be certain that the seatback is securely Do not allow children to have access to the trunk surface push the trunk lid down until you trunk, either by climbing into the trunk from locked into position.
Page 62
Grocery Bag Hooks WARNING! (Continued) The rear cargo area is equipped with grocery • Place as much cargo as possible in front of bag hooks, located on either side of the rear the rear axle. Too much weight or improp- cargo area.
INTERNAL EQUIPMENT WARNING! Storage Do not operate this vehicle with a console compartment lid in the open position. Driving Glove Compartment with the console compartment lid open may The glove compartment is located on the pas- result in injury in a collision. senger side of the instrument panel.
Rear Seat Armrest Storage — If Equipped Lighted Cupholders — If Equipped For rear passengers there is a storage bin On some vehicles the rear cupholders are located in the armrest. Lift upward on the latch equipped with a light ring that illuminates the to open the storage compartment.
Heated And Cooled Cupholders — If The front power outlet is located inside the WARNING! (Continued) Equipped storage area on the center stack of the instru- medication, exhaustion or other physical Your vehicle may be equipped with heated and ment panel. condition must exercise particular care in cooled cupholders.
Page 66
In addition to the front power outlet, there is also WARNING! (Continued) a power outlet located in the storage area of the • Close the lid when not in use and while center console. driving the vehicle. • If this outlet is mishandled, it may cause an electric shock and failure.
case on your phone. Set the phone on the To get your free aftermarket phone case or CAUTION! (Continued) wireless charging pad face up. The charging Qi Adapter, go to • Power outlets are designed for accessory indicator on your phone will light up indicating http://invehiclewirelesscharging.com.
4. Fuel Gauge Location And Controls CAUTION! The instrument cluster display features an inter- • The pointer shows the level of fuel in the active display which is located in the instrument Driving with a hot engine cooling system fuel tank when the Keyless Push Button cluster.
• Upon returning to a main menu, the last Engine Oil Life Reset submenu screen viewed within that main Oil Change Required menu will be displayed. Your vehicle is equipped with an engine oil OK Button: change indicator system. The “Oil Change Re- quired”...
3. Push and release the right arrow button to NOTE: Instrument Cluster Display access the ”Oil Life” screen. If the indicator message illuminates when you Selectable Menu Items start the vehicle, the oil change indicator system Push and release the up or down arrow button 4.
Page 73
• 0-100 MPH (0-161 km/h) Timer Performance The following describes each feature and its operation: – Best WARNING! – Last Driver Assist The Driver Assist menu provides the status and Measurement of vehicle statistics with the – Recent visuals about the Adaptive Cruise Control and Performance Features is intended for off- –...
Page 74
• LaneSense Off Push the SET + or the SET- button (located on Trip Info the steering wheel) and the following will display Push and release the up or down arrow button • When LaneSense is deactivated, the display in the instrument cluster display: until the Trip Menu item is displayed in the will read “LaneSense Off.”...
Page 75
• Average (MPG, L/100 km, or km/L) • “Checking System for Diagnostic Codes.” 1. Upper Left • Current (MPG, L/100 km, or km/L) • Compass (default) • Driver must push the OK button again to see • Trip A Distance •...
passive speed limiter telltale will turn yellow and These messages indicate the vehicle battery Loss of the battery charge may indicate one or will flash, and a pop up message of “Speed has a low state of charge and continues to lose more of the following conditions: Warning Exceeded”...
brake application. If the brake light turns on it What to do when an electrical load reduction WARNING LIGHTS AND action message is present (“Battery Saver may indicate that the parking brake is applied, MESSAGES On” or “Battery Saver Mode”) that the brake fluid level is low, or that there is a The warning/indicator lights will illuminate in the problem with the anti-lock brake system.
Page 78
If brake failure is indicated, immediate repair is — Battery Charge Warning Light (ETC) system. If a problem is detected while the necessary. This warning light will illuminate when the bat- vehicle is running, the light will either stay on or tery is not charging properly.
If the light turns on while driving, safely pull over passenger seat belt remains unbuckled, the CAUTION! and stop the vehicle. If the A/C system is on, Seat Belt Reminder Light will flash or remain on Continuous driving with the Transmission turn it off.
Page 80
Certain conditions, such as a loose or missing — Electronic Stability Control (ESC) Off CAUTION! (Continued) gas cap, poor quality fuel, etc., may illuminate Warning Light — If Equipped flashing, severe catalytic converter damage the light after engine start. The vehicle should be This warning light indicates the Electronic Sta- and power loss will soon occur.
Page 81
even if under-inflation has not reached the level CAUTION! (Continued) CAUTION! (Continued) to trigger illumination of the TPMS low tire the vehicle, avoiding sharp braking and may result when using replacement equip- pressure telltale. steering. If a tire puncture occurs, repair ment that is not of the same size, type, and/or Your vehicle has also been equipped with a immediately using the dedicated tire repair kit...
RUN position, have the brake system inspected — Service Adaptive Cruise Control — Cruise Control Set Indicator Light — by an authorized dealer. Warning Light — If Equipped If Equipped This light will turn on when a ACC is not oper- This indicator light will illuminate when the —...
NOTE: — Custom Mode Indicator Light rearward (toward the rear of the vehicle) to turn This light will turn on when Custom Mode is off the high beams. If the high beams are off, pull • A continuous chime will sound if the vehicle is active.
NOTE: CAUTION! (Continued) WARNING! (Continued) If you crank or start the engine, you will have to be serviced before any emissions tests can could occur that may result in an acci- start this test over. be performed. dent involving serious injury or death. •...
Page 85
Regardless of whether your vehicle’s OBD II system is ready or not, if the MIL is illuminated during normal vehicle operation you should have your vehicle serviced before going to the I/M station. The I/M station can fail your vehicle because the MIL is on with the engine running.
SAFETY FEATURES ABS is designed to function with the OEM tires. WARNING! Modification may result in degraded ABS perfor- • The ABS contains sophisticated electronic mance. Anti-Lock Brake System (ABS) equipment that may be susceptible to in- The Anti-Lock Brake System (ABS) provides Anti-Lock Brake Warning Light terference caused by improperly installed increased vehicle stability and brake perfor-...
Page 88
ing wheel angle and vehicle’s speed are suffi- gether to enhance both vehicle stability and WARNING! (Continued) control in various driving conditions. cient to potentially cause wheel lift, it then on very slippery surfaces, or hydroplaning. applies the appropriate brake and may also Your vehicle may also be equipped with Ready The capabilities of a BAS-equipped vehicle reduce engine power to lessen the chance that...
Page 89
Electronic Stability Control (ESC) WARNING! WARNING! (Continued) This system enhances directional control and • Electronic Stability Control (ESC) cannot nance that reduces the effectiveness of the stability of the vehicle under various driving prevent the natural laws of physics from ESC system can increase the risk of loss of conditions.
Page 90
• Trailer Sway control (TSC) is disabled when SPORT), and the light in the cluster is illumi- WARNING! (Continued) nated. The second push of the ESC button the the ESC system is in the “Partial Off” mode. • The Electronic Stability Control (ESC) can- system will go into TRACK mode, indication •...
Page 91
Malfunction Indicator Light” also flashes when apply the throttle before this time expires, the WARNING! (Continued) TCS is active. If the “ESC Activation/Malfunction system will release brake pressure and the sibility to be attentive to distance to other Indicator Light” begins to flash during accelera- vehicle will roll down the hill as normal.
Page 92
5. Rotate the steering wheel slightly more than Ready Alert Braking (RAB) WARNING! (Continued) Ready Alert Braking may reduce the time re- one-half turn to the left. • HSA is not a parking brake. Always apply quired to reach full braking during emergency 6.
AUXILIARY DRIVING SYSTEMS tends beyond the side of your vehicle, this may result in the BSM warning light randomly alerting on the trailer or even remaining illu- Blind Spot Monitoring (BSM) — If minated the entire time the vehicle is in a Equipped forward gear.
Page 94
addition to sounding an audible (chime) alert The BSM system is designed not to issue an and reducing the radio volume if the corre- alert on stationary objects such as guardrails, sponding turn signal is activated. Refer to posts, walls, foliage, berms, etc. However, oc- “Modes Of Operation”...
Page 95
WARNING! Rear Cross Path Detection (RCP) is not a back up aid system. It is intended to be used to help a driver detect an oncoming vehicle in a parking lot situation. Drivers must be care- ful when backing up, even when using RCP. Always check carefully behind your vehicle, look behind you, and be sure to check for pedestrians, animals, other vehicles, ob-...
Blind Spot Alert Lights/Chime Forward Collision Warning (FCW) braking to mitigate the potential forward colli- sion. If the Forward Collision Warning with Miti- With Mitigation Operation When operating in Blind Spot Alert Lights/Chime The Forward Collision Warning (FCW) system gation event stops the vehicle completely, the mode, the BSM system will provide a visual alert with mitigation provides the driver with audible system will hold the vehicle at standstill for two...
Page 97
• FCW may not react to irrelevant objects such Active Braking events within an ignition cycle, Changing the FCW status to off prevents the the Active Braking portion of FCW will be system from warning you of a possible collision as overhead objects, ground reflections, ob- deactivated until the next ignition cycle.
Tire Pressure Monitoring System Once the low tire pressure warning (TPMS CAUTION! Warning Light) illuminates, you must increase (TPMS) • The TPMS has been optimized for the the tire pressure to the recommended cold The Tire Pressure Monitor System (TPMS) will original equipment tires and wheels.
Page 99
NOTE: NOTE: It is particularly important for you to check the • The TPMS is not intended to replace normal tire pressure in all of the tires on your vehicle tire care and maintenance or to provide warn- monthly and to maintain the proper pressure. ing of a tire failure or condition.
Page 100
NOTE: the system fault no longer exists, the TPMS 3. After driving the vehicle for up to 20 minutes Warning Light will no longer flash, and the When filling warm tires, the tire pressure may above 15 mph (24 km/h), the TPMS Warning "Service Tire Pressure System"...
TPMS Deactivation — If Equipped the "Service Tire Pressure System" message Here are some simple steps you can take to will no longer be displayed as long as no system minimize the risk of harm from a deploying air The Tire Pressure Monitoring System (TPMS) fault exists.
4. Never allow children to slide the shoulder Enhanced Seat Belt Use Reminder System WARNING! (Continued) (BeltAlert) belt behind them or under their arm. • Never install a rear-facing child restraint in Driver and Passenger BeltAlert (if equipped) 5. You should read the instructions provided the front seat of a vehicle.
Page 103
minder Light and sounding an intermittent NOTE: WARNING! (Continued) chime. Once the BeltAlert warning sequence If BeltAlert has been deactivated and the driver • In a collision, you and your passengers can has completed, the Seat Belt Reminder Light or outboard front seat passenger (if equipped suffer much greater injuries if you are not will remain on until the seat belts are buckled.
Page 104
Lap/Shoulder Belt Operating Instructions WARNING! (Continued) WARNING! (Continued) 1. Enter the vehicle and close the door. Sit back • Two people should never be belted into a buckle your seat belt into the buckle near- and adjust the seat. single seat belt. People belted together can est you.
Page 105
5. Position the shoulder belt across the shoul- Adjustable Upper Shoulder Belt Anchorage In the driver and outboard front passenger der and chest with minimal, if any slack so seats, the top of the shoulder belt can be that it is comfortable and not resting on your adjusted upward or downward to position the neck.
Page 106
NOTE: Seat Belts And Pregnant Women NOTE: The adjustable upper shoulder belt anchorage is These devices are not a substitute for proper equipped with an Easy Up feature. This feature seat belt placement by the occupant. The seat allows the shoulder belt anchorage to be ad- belt still must be worn snugly and positioned justed in the upward position without pushing or properly.
Page 107
erly restrained in the rear seat of a vehicle with How To Disengage The Automatic Locking a rear seat. Mode Unbuckle the combination lap/shoulder belt and WARNING! allow it to retract completely to disengage the Automatic Locking Mode and activate the ve- •...
• The Air Bag Warning Light does not come on Supplemental Restraint Systems Air Bag Warning Light The ORC monitors the readiness of the elec- during the four to eight seconds when the (SRS) tronic parts of the air bag system ignition switch is first in the ON/RUN position.
Page 109
Redundant Air Bag Warning Light WARNING! (Continued) If a fault with the Air Bag Warning Light is • Never install a rear-facing child restraint in detected, which could affect the the front seat of a vehicle. Only use a Supplemental Restraint System rear-facing child restraint in the rear seat.
Page 110
ger seat belt is buckled. The seat belt buckle Front Air Bag Operation Knee Impact Bolsters switch may adjust the inflation rate of the Ad- Front Air Bags are designed to provide addi- The Knee Impact Bolsters help protect the vanced Front Air Bags.
Page 111
front seats. The SABs are marked with “SRS SABICs (if equipped with SABICs) may help WARNING! AIRBAG” or “AIRBAG” on a label or on the seat reduce the risk of head and other injuries to front Do not use accessory seat covers or place trim on the outboard side of the seats.
Page 112
angles, or some side collisions that do not WARNING! (Continued) WARNING! impact the area of the passenger compartment. • In order for the SABICs to work as in- • Side Air Bags need room to inflate. Do not The Side Air Bags may deploy during angled or tended, do not install any accessory items lean against the door or window.
Page 113
• Instrument Panel • As the air bags deflate, you may see some • After any collision, the vehicle should be smoke-like particles. The particles are a nor- taken to an authorized dealer immediately. • Knee Impact Bolsters mal by-product of the process that generates Enhanced Accident Response System •...
Page 114
• Brake booster Maintaining Your Air Bag System WARNING! (Continued) • Electric park brake accessories may be used. If it is necessary • Automatic transmission gear selector WARNING! to modify the air bag system for persons • Horn • Modifications to any part of the air bag with disabilities, contact an authorized •...
NOTE: WARNING! (Continued) EDR data are recorded by your vehicle only if a • In a collision, an unrestrained child can non-trivial crash situation occurs; no data are become a projectile inside the vehicle. The recorded by the EDR under normal driving con- force required to hold even an infant on ditions and no personal data (e.g., name, gen- your lap could become so great that you...
Page 116
Summary Of Recommendations For Restraining Children In Vehicles Child Size, Height, Weight Or Age Recommended Type Of Child Restraint Children who are two years old or younger Either an Infant Carrier or a Convertible Child Infants and Toddlers and who have not reached the height or Restraint, facing rearward in a rear seat of weight limits of their child restraint the vehicle...
Page 117
3. Does the shoulder belt cross the child’s Older Children And Child Restraints WARNING! (Continued) Children who are two years old or who have shoulder between the neck and arm? • After a child restraint is installed in the outgrown their rear-facing convertible child seat 4.
Page 118
Recommendations For Attaching Child Restraints Restraint Type Combined Weight Use Any Attachment Method Shown With An “X” Below of the Child + Child LATCH – Lower An- Seat Belt Only LATCH – Lower An- Seat Belt + Top Restraint chors Only chors + Top Tether Tether Anchor Anchor...
Page 119
Lower Anchors And Tethers For CHildren age but no lower anchorages. In these seating (LATCH) Restraint System positions, the seat belt must be used with the top tether anchorage to install the child restraint. Please see the following table for more information.
Page 120
Frequently Asked Questions About Installing Child Restraints With LATCH Do not use the seat belt when you use the LATCH anchorage system to attach a rear- Can the LATCH anchorages and the seat belt facing or forward-facing child restraint. be used together to attach a rear-facing or Booster seats may be attached to the LATCH forward-facing child restraint? anchorages if allowed by the booster seat...
Page 121
Locating The LATCH Anchorages WARNING! The lower anchorages are round bars that are found at the rear of the seat cush- Never use the same lower anchorage to ion where it meets the seatback, attach more than one child restraint. Please below the anchorage symbols on refer to “To Install A LATCH-Compatible Child the seatback.
Page 122
seat. You may also move the front seat belt could injure a child if they play with it and Installing Child Restraints Using The accidentally lock the seat belt retractor. Before Vehicle Seat Belt forward to allow more room for the child seat. installing a child restraint using the LATCH Child restraint systems are designed to be se- 3.
Page 123
Lap/Shoulder Belt Systems For Installing Child Restraints In This Vehicle Automatic Locking Retractor (ALR) Locations ALR = Switchable Automatic Locking Retractor Top Tether Anchorage Symbol Frequently Asked Questions About Installing Child Restraints With Seat Belts What is the weight limit (child’s weight + weight Always use the tether anchor when using the of the child restraint) for using the Tether An- seat belt to install a forward facing child re-...
Page 124
Installing A Child Restraint With A 2. Pull enough of the seat belt webbing from the 8. If the child restraint has a top tether strap and Switchable Automatic Locking Retractor retractor to pass it through the belt path of the seating position has a top tether anchor- (ALR): the child restraint.
Page 125
between the two posts. If not possible, lower WARNING! (Continued) WARNING! (Continued) the head restraint and pass the tether strap See the section “Lower Anchors and Tethers sible injury to the child. Use only the an- around the outboard side of the head re- for CHildren (LATCH) Restraint System”...
Transporting Pets Exhaust Gas plete exhaust system and adjacent body areas for broken, damaged, deteriorated, or misposi- Air Bags deploying in the front seat could harm tioned parts. Open seams or loose connections your pet. An unrestrained pet will be thrown WARNING! could permit exhaust fumes to seep into the about and possibly injured, or injure a passen-...
Page 127
comes on intermittently or remains on while WARNING! (Continued) WARNING! (Continued) driving, have an authorized dealer service the • ALWAYS securely attach • ONLY use the passenger’s side floor mat your floor mat vehicle immediately. using the floor mat fasteners. DO NOT on the passenger’s side floor area.
Periodic Safety Checks You Should WARNING! WARNING! (Continued) Make Outside The Vehicle • In a collision, you and your passengers can To prevent SERIOUS INJURY or DEATH Tires when using “Track-Use” parts and equip- suffer much greater injuries if you are not Examine tires for excessive tread wear and ment: properly buckled up.
STARTING THE ENGINE Automatic Transmission This feature allows the driver to operate the ignition switch with the push of a button, as long The gear selector must be in the PARK position Before starting your vehicle, adjust your seat, as the Remote Start/Keyless Enter-N-Go key before you can start the engine.
Page 134
3. If the gear selector is not in PARK, the ENGINE START/STOP Button Functions — WARNING! With Driver’s Foot OFF The Brake Pedal (In ENGINE START/STOP button must be held • Driver inattention could lead to failure to PARK Or NEUTRAL Position) for two seconds or three short pushes in a place the vehicle in PARK.
NOTE: If the driver shifts into PARK while moving, If Engine Fails To Start the vehicle may AutoPark. For Keyless Go equipped vehicles, The engine If the engine fails to start after you have followed the "Normal Starting" or "Extreme Cold will turn off and the ignition switch will change to AutoPark will engage ONLY when vehicle speed Weather"...
wearing in occurs mainly during the first 300 to 500 miles (483 to 805 km): WARNING! (Continued) 500 miles (805 km) and continues through the • Exercise the full engine rpm range, shifting • If the vehicle has a discharged battery, first oil change interval.
Page 137
difficult to move the gear selector out of PARK. WARNING! (Continued) The parking brake should always be applied • Do not leave the key fob in or near the whenever the driver is not in the vehicle. vehicle or in a location accessible to chil- dren, and do not leave the ignition of a WARNING! vehicle equipped with Keyless Enter-N-Go...
AUTOMATIC TRANSMISSION WARNING! (Continued) WARNING! (Continued) • Do not leave the key fob in or near the You could lose control of the vehicle and hit WARNING! someone or something. Only shift into gear vehicle (or in a location accessible to chil- •...
transmission in PARK. This system also locks ing at low speeds). To shift past multiple gear the transmission in PARK whenever the ignition ranges at once (such as PARK to DRIVE), is in the OFF mode. simply rotate the gear selector to the appropri- ate detent.
Page 140
PARK (P) WARNING! (Continued) WARNING! (Continued) This range supplements the parking brake by trying to move the transmission gear selec- transmission into PARK, and turn the igni- locking the transmission. The engine can be tor out of PARK with the brake pedal re- tion OFF.
Page 141
traveling into strong head winds), use the CAUTION! WARNING! Paddle Shifters (refer to “Paddle Shift Mode” in • Before moving the transmission gear se- Do not coast in NEUTRAL and never turn off this section for further information) to select a lector out of PARK, you must start the the ignition to coast down a hill.
Page 142
cator Light (MIL) may be illuminated. A message rized dealer has diagnostic equipment to assess the current gear. When Paddle Shift is active, in the instrument cluster will inform the driver of the condition of your transmission. the current transmission gear is displayed in the the more serious conditions, and indicate what instrument cluster.
• The system will ignore attempts to upshift at • Launch Control should only be used when the NOTE: too low of a vehicle speed. engine and transmission are at operating Refer to “SRT Drive Modes” in “Multimedia” for temperature. further descriptions of these modes.
NOTE: 6. Hold the brake and make sure the vehicle is NOTE: in “DRIVE”. After launch control has been aborted, ESC will Use of DOT 4 brake fluid is suggested for return to its current ESC mode. extended track usage due to increased thermal 7.
• For race track usage it is recommended that the brakes are not smoking. If they are, do 8. Rotors that pulsate during track use should the axle fluid be changed every 4 hours of on another cool down lap. be replaced.
If the Electric Power Steering warn- SPEED CONTROL — IF To Activate ing icon is displayed and the “SER- Push the on/off button to activate the Speed EQUIPPED VICE POWER STEERING” or the Control. “CRUISE CONTROL READY” will ap- When engaged, the Speed Control takes over “POWER STEERING ASSIST OFF pear in the instrument cluster display to indicate accelerator operations at speeds greater than...
To Vary The Speed Setting To Decrease Speed To Accelerate For Passing To Increase Speed Press the accelerator as you would normally. When the Speed Control is set, you can de- When the pedal is released, the vehicle will crease speed by pushing the SET (-) button. When the Speed Control is set, you can in- return to the set speed.
• If the ACC sensor detects a vehicle ahead, To Deactivate WARNING! ACC will apply limited braking or accelerate A soft tap on the brake pedal, pushing the CANC • Adaptive Cruise Control (ACC) is a conve- (not to exceed the original set speed) auto- button, or normal brake pressure while slowing nience system.
Adaptive Cruise Control (ACC) Activating Adaptive Cruise Control WARNING! (Continued) Operation (ACC) • Will bring the vehicle to a complete stop The Speed Control buttons (located on the right You can only engage ACC if the vehicle speed is while following a target vehicle and hold side of the steering wheel) operates the ACC above 0 mph (0 km/h).
• When the driver’s door is open at low speeds. set when the vehicle speed is above 19 mph (30 km/h), the set speed shall be the current • When the driver’s seat belt is unbuckled at speed of the vehicle. low speeds.
• The vehicle parking brake is applied. increase in set speed is reflected in the WARNING! instrument cluster display. • Driver seatbelt is unbuckled at low speeds. The Resume function should only be used if Metric Speed (km/h) • Driver door is opened at low speeds. traffic and road conditions permit.
• The ACC will bring the vehicle to a complete decrease in set speed is reflected in the instrument cluster display. stop while following a target vehicle and hold the vehicle for two seconds in the stop posi- Metric Speed (km/h) tion.
If there is no vehicle ahead, the vehicle will maintain the set speed. If a slower moving vehicle is detected in the same lane, the instru- ment cluster displays the “Sensed Vehicle Indi- cator” icon, and the system adjusts vehicle speed automatically to maintain the distance setting, regardless of the set speed.
When ACC is set, the set speed will show in the NOTE: WARNING! instrument cluster display. When the vehicle transitions from a location with left hand drive traffic to a location with right hand When the ACC system is resumed, the driver The ACC screen may display once again if any must ensure that there are no pedestrians, drive traffic or vice-versa, the ACC system will...
Page 155
• Do not attach or install any accessories near while driving in highly reflective areas (i.e. tun- FCW Limited Functionality Clean Front Wind- nels with reflective tiles, or ice and snow). The the sensor, including transparent material or shield” and the system will have degraded per- ACC system will recover after the vehicle has aftermarket grilles.
Service ACC/FCW Warning Offset Driving Turns And Bends If the system turns off, and the instrument ACC may not detect a vehicle in the same lane When driving on a curve with ACC engaged, the cluster displays “ACC/FCW Unavailable Service that is offset from your direct line of travel, or a system may decrease the vehicle speed and Required”...
Using ACC On Hills react in situations where the vehicle you are When driving on hills, ACC may not detect a following exits your lane and the vehicle ahead vehicle in your lane. Depending on the speed, is stopped in your lane. Always be attentive and vehicle load, traffic conditions, and the steep- ready to apply the brakes if necessary.
Page 158
button will result in turning on (changing to) the To Vary The Speed Setting To Decrease Speed Normal (Fixed Speed) Cruise Control mode. To Increase Speed When the Normal (Fixed Speed) Cruise Control When the Normal (Fixed Speed) Cruise Control is set, you can decrease speed by pushing the WARNING! is set, you can increase speed by pushing the...
To Cancel PARKSENSE FRONT AND ParkSense Sensors The following conditions will cancel the Normal The four ParkSense sensors, located in the rear REAR PARK ASSIST — IF (Fixed Speed) Cruise Control without clearing fascia/bumper, monitor the area behind the ve- EQUIPPED the memory: hicle that is within the sensors’...
ParkSense Warning Display ParkSense Display The ParkSense Warning screen will only be Rear Park Assist displayed if Sound and Display is selected from the Customer Programmable Features section While the vehicle is in REVERSE, the of the Uconnect System. Refer to "Uconnect ParkSense Display is shown in the instrument Settings”...
Page 161
The vehicle is close to the obstacle when the warning display shows one flashing arc and sounds a continuous tone. The following chart shows the warning alert operation when the system is detecting an obstacle: Slow Tone/Solid Arc Fast Tone/Flashing Arc Fast Tone/Flashing Arc Continuous Tone/Flashing Arc...
Page 163
Front Park Assist When the vehicle is in DRIVE the ParkSense Warning screen will be displayed when an ob- stacle is detected. The system will indicate a detected obstacle by showing a single arc in one or more regions based on the obstacle’s distance and location relative to the vehicle.
Page 164
WARNING ALERTS Front Distance Greater than 47-39 inches 39-25 inches 25-12 inches Less than (inches/cm) 47 inches (120 cm) (120-100 cm) (100-65 cm) (65-30 cm) 12 inches (30 cm) Arcs — Left None None None 2nd Flashing 1st Flashing Arcs — Center None 4th Solid 3rd Flashing...
Enabling And Disabling ParkSense "PARKSENSE UNAVAILABLE SERVICE RE- and then cycle the ignition. If the message QUIRED" message for five seconds. When the continues to appear see your authorized dealer. ParkSense can be enabled and disabled with gear selector is moved to REVERSE and the the ParkSense switch, located on the switch If the "PARKSENSE UNAVAILABLE SERVICE system has detected a faulted condition, the...
• ParkSense, when on, will reduce the volume WARNING! (Continued) CAUTION! (Continued) of the radio when it is sounding a tone. • The vehicle must be driven slowly when up. You are responsible for safety and must • Clean the ParkSense sensors regularly, tak- continue to pay attention to your surround- using ParkSense in order to be able to stop ing care not to scratch or damage them.
When only a single lane marking is detected and NOTE: Left Lane Departure — Only Left Lane De- the driver unintentionally drifts across the lane tected The LaneSense system will retain the last sys- marking (no turn signal applied), the LaneSense tem state, on or off, from the last ignition cycle •...
Left Lane Departure — Both Lanes Detected • When the LaneSense system is on, the lane lines turn from gray to white to indicate that both of the lane markings have been de- tected. The LaneSense telltale is solid green when both lane markings have been detected and the system is “armed”...
NOTE: Manual Activation Of The Rear View Camera: When enabled, active guide lines are overlaid on the image to illustrate the width of the vehicle • When enabled the system operates above 1. Press the "Controls" button located on the and its projected backup path based on the 37 mph (60 km/h) and below 112 mph bottom of the Uconnect display.
REFUELING THE VEHICLE NOTE: WARNING! In certain cold conditions, ice may prevent the 1. Push the fuel filler door release switch (lo- Drivers must be careful when backing up fuel door from opening. If this occurs, lightly cated in the driver’s door map pocket). even when using the ParkView Rear Back Up push on the fuel door to break the ice buildup Camera.
Emergency Fuel Filler Door Release If you are unable to open the fuel filler door, use the fuel filler door emergency release located in the trunk. Follow the steps below to open the fuel door in case of an emergency: 1.
• Vehicle Identification Number (VIN) Overloading NOTE: The load carrying components (axle, springs, • Type of vehicle • Refer to the “Vehicle Certification Label” af- tires, wheels, etc.) of your vehicle will provide fixed to the rear of the driver’s door for your •...
Gross Trailer Weight (GTW) typically provides adjustable friction associated WARNING! The GTW is the weight of the trailer plus the with the telescoping motion to dampen any It is important that you do not exceed the weight of all cargo, consumables, and equip- unwanted trailer swaying motions while travel- maximum front or rear GAWR.
NOTE: NOTE: WARNING! (Continued) The trailer tongue weight must be considered as Remember that everything put into or on the engine, transmission, steering, suspen- part of the combined weight of occupants and trailer adds to the load on your vehicle. Also, sion, chassis structure or tires.
Page 175
nance intervals. When towing a trailer, never “Tires” in “Servicing And Maintenance” for the WARNING! (Continued) exceed the GAWR or GCWR ratings. proper inspection procedure. • Towing any trailer will increase your stopping • When replacing tires, refer to “Tires” in “Ser- distance.
The electrical connections are all complete to NOTE: the vehicle but you must mate the harness to a Using a lower gear while operating the vehicle trailer connector. Refer to the following illustra- under heavy loading conditions will improve tions. performance and extend transmission life by reducing excessive shifting and heat buildup.
• Slow down during rainstorms or when the Cooling System DRIVING TIPS To reduce potential for engine and transmission roads are slushy. overheating, take the following actions: Driving On Slippery Surfaces • Slow down if the road has standing water or Information in this section will aid in safe con- City Driving puddles.
Page 178
WARNING! (Continued) CAUTION! • Always check the depth of the standing your vehicle away swiftly. Failure to follow this warning may result in injuries that are water before driving through it. Never drive serious or fatal to you, your passengers, and through standing water that is deeper than others around you.
This is an emergency warning system and it HAZARD WARNING FLASHERS BULB REPLACEMENT should not be used when the vehicle is in The Hazard Warning flasher switch is located on motion. Use it when your vehicle is disabled and Replacement Bulbs the switch bank just above the climate controls.
Exterior Bulbs Bulb Number Low Beam/High Beam (Bi-Halogen Headlamp) 9005HL+ Low Beam/High Beam (Bi-Xenon Headlamp) D3S (Serviced At Authorized Dealer) Front Turn Signal Lamp PSY24WSV Front Park Lamp LED (Serviced At Authorized Dealer) Daytime Running Lamp LED (Serviced At Authorized Dealer) Front Fog Lamp –...
Page 183
4. Twist the headlamp bulb assembly counter- Front Turn Signal Lamps The Front Park/Turn function is part of the clockwise, and then pull it out of the head- headlamp assembly and use LED lamps that lamp assembly. are not serviceable separately. The headlamps must be replaced as an assembly, see your authorized dealer.
FUSES When a device does not work, you must check the fuse element inside the blade fuse for a break/melt. WARNING! Also, please be aware that when using power • When replacing a blown fuse, always use outlets for extended periods of time with the an appropriate replacement fuse with the engine off may result in vehicle battery dis- same amp rating as the original fuse.
Page 185
Cavity Cartridge Fuse Mini-Fuse Description – – Fuse – Spare 40 Amp Green – Radiator Fan #1 – (Non 6.2L Supercharged) 50 Amp Red – Electric Power Steering #1 – If Equipped 30 Amp Pink – Starter 40 Amp Green –...
Page 186
Cavity Cartridge Fuse Mini-Fuse Description 30 Amp Pink – Headlamp Washers – If Equipped 20 Amp Blue – Police Police Bat Feed #2 40 Amp Green / 20 Amp – Engine Cooling Pump (6.2L Supercharged) / Police Blue – Police Bat Feed # 3 20 Amp Blue –...
Cavity Cartridge Fuse Mini-Fuse Description – – Fuse – Spare – – Fuse – Spare – 20 Amp Yellow Vacuum Pump – 5 Amp Tan Adaptive Cruise – If Equipped – – Fuse – Spare Rear Interior Fuses CAUTION! There is also a power distribution center located •...
NOTE: JACKING AND TIRE 5. Rotate the fastener securing the jack coun- The spare tire must be removed in order to terclockwise to remove it. CHANGING access the jack. 1. Open the trunk. WARNING! 2. Lift the access cover using the pull strap. •...
Preparations For Jacking Jacking And Changing A Tire 1. Park the vehicle on a firm, level surface. WARNING! Avoid ice or slippery areas. Carefully follow these tire changing warnings to help prevent personal injury or damage to WARNING! your vehicle: Do not attempt to change a tire on the side of •...
Page 194
Spare Tire Label Jacking Locations Rear Jacking Location 2. If equipped with aluminum wheels where the 4. Place the jack underneath the lift area that is 5. Raise the vehicle just enough to remove the center cap covers the lug nuts, use the lug closest to the flat tire.
Road Tire Installation WARNING! (Continued) 1. Mount the road tire on the axle. the vehicle has been lowered. Failure to follow this warning may result in serious 2. Install the remaining lug nuts with the cone injury. shaped end of the nut toward the wheel. Lightly tighten the lug nuts.
be dangerous if done improperly, so please 1. Apply the parking brake, shift the automatic follow the procedures in this section carefully. transmission into PARK and cycle the ignition to OFF. WARNING! 2. Turn off the heater, radio, and all unneces- sary electrical accessories.
NOTE: minutes, and then start the engine in the If frequent jump starting is required to start your vehicle you should have the battery and charg- Make sure at all times that unused ends of vehicle with the discharged battery. ing system tested at an authorized dealer.
• You can also turn the temperature control to MANUAL PARK RELEASE maximum heat, the mode control to floor and the blower control to high. This allows the WARNING! heater core to act as a supplement to the radiator and aids in removing heat from the Always secure your vehicle by fully applying engine cooling system.
6. While holding the locking tab in the disen- 4. Tuck the tether strap into the base of the WARNING! gaged position, pull the tether strap to rotate console. Reinstall the console storage bin. the lever up and rearward, until it locks in Fast spinning tires can be dangerous.
TOWING A DISABLED VEHICLE CAUTION! (Continued) This section describes procedures for towing a • Revving the engine or spinning the wheels disabled vehicle using a commercial towing too fast may lead to transmission overheat- service. ing and failure. It can also damage the tires.
and the transmission is operable, the vehicle CAUTION! (Continued) may be flat towed (with all four wheels on the • Please refer to the “Towing A Disabled ground) under the following conditions: Vehicle” section for detailed instructions. • The transmission must be in NEUTRAL. Re- Damage to your vehicle may occur if these fer to "Manual Park Release"...
Front Tow Eye Installation Please refer to “Occupant Restraint Systems” in The front tow eye receptacle is located behind a “Safety” for further information on the Event door on the front bumper fascia. Data Recorder (EDR). To install the tow eye, open the door using the vehicle key or a small screwdriver, and thread the tow eye into the receptacle.
Checking Oil Level To prevent freeze-up of your windshield washer system in cold weather, select a solution or To assure proper engine lubrication, the engine mixture that meets or exceeds the temperature oil must be maintained at the correct level. range of your climate.
Engine Oil Selection DEALER SERVICE WARNING! (Continued) For best performance and maximum protection An authorized dealer has the qualified service • Battery posts, terminals, and related ac- under all types of operating conditions, the personnel, special tools, and equipment to per- cessories contain lead and lead com- manufacturer recommends the use of a full form all service operations in an expert manner.
Disposing Of Used Engine Oil And Oil WARNING! (Continued) WARNING! (Continued) Filters the air induction system (air cleaner, hoses, your air conditioning system. Some unap- Care should be taken in disposing of used etc.) unless such removal is necessary for proved refrigerants are flammable and can engine oil and oil filters from your vehicle.
Refrigerant Recovery And Recycling R-134a — If Equipped R-134a Air Conditioning Refrigerant is a hydro- fluorocarbon (HFC) that is an ozone-friendly substance. The manufacturer recommends that air conditioning service be performed by an authorized dealer or other service facilities using recovery and recycling equipment.
• Rib or belt wear also be given to hood latching components to WARNING! (Continued) ensure proper function. When performing other • Longitudinal belt cracking (cracks between • You can be badly injured working on or underhood services, the hood latch, release two ribs) around a motor vehicle.
Page 212
Wiper Blade Removal/Installation CAUTION! Do not allow the wiper arm to spring back against the glass without the wiper blade in place or the glass may be damaged. 1. Lift the wiper arm to raise the wiper blade off of the glass, until the wiper arm is in the full up position.
4. Slide the wiper blade onto the arm until WARNING! (Continued) CAUTION! (Continued) motion stops, then fold down the locking tab colorless and odorless. Breathing it can hicle with a severe malfunction could to secure. make you unconscious and can eventually cause the converter to overheat, resulting NOTE: poison you.
• Do not idle the engine with any spark plug If the engine coolant (antifreeze) is dirty or WARNING! (Continued) wires disconnected or removed, such as contains visible sediment, have an authorized • When working near the radiator cooling when diagnostic testing, or for prolonged dealer clean and flush with OAT coolant (anti- fan, disconnect the fan motor lead or turn periods during very rough idle or malfunction-...
Page 215
• This vehicle has not been designed for use • Mix a minimum solution of 50% OAT engine Cooling System Pressure Cap with propylene glycol-based engine coolant coolant that meets the requirements of FCA The cap must be fully tightened to prevent loss (antifreeze).
ground. If ingested by a child or pet, seek stat opens, allowing hot engine coolant (anti- Brake System emergency assistance immediately. Clean up freeze) to enter the radiator. In order to assure brake system performance, any ground spills immediately. all brake system components should be in- If an examination of your engine compartment spected periodically.
pected to fall as the brake pads wear. However, NOTE: WARNING! (Continued) low fluid level may be caused by a leak and a No chemical flushes should be used in any hard or prolonged braking, resulting in sud- checkup may be needed. transmission;...
Fluid Level Check Rear Axle Safety The fluid level is preset at the factory and does For normal service, periodic fluid level checks not require adjustment under normal operating are not required. When the vehicle is serviced WARNING! conditions. Routine fluid level checks are not for other reasons the exterior surfaces of the •...
Page 219
• Inspect tires for signs of tire wear or visible NOTE: creased by 3 psi (21 kPa), which equals 1 psi damage. (7 kPa) for every 12°F (7°C) for this outside • Unequal tire pressures from side to side may temperature condition.
Page 220
Radial Ply Tires Run Flat Tires — If Equipped WARNING! Run Flat tires allow you the capability to drive 50 miles (80 km) at 50 mph (80 km/h) after a Fast spinning tires can be dangerous. Forces WARNING! rapid loss of inflation pressure. This rapid loss of generated by excessive wheel speeds may Combining radial ply tires with other types of inflation is referred to as the Run Flat mode.
Page 221
It is recommended you contact an authorized These indicators are molded into the bottom of WARNING! (Continued) the tread grooves. They will appear as bands tire dealer or original equipment dealer with any and have a collision resulting in serious injury when the tread depth becomes a 1/16 of an inch questions you may have on tire specifications or or death.
roads are covered with ice or snow. For more speeds over 75 mph (120 km/h). For speeds WARNING! (Continued) information, contact an authorized dealer. above 75 mph (120 km/h) refer to original equip- • Failure to equip your vehicle with tires ment or an authorized tire dealer for recom- Summer tires do not contain the all season having adequate speed capability can re-...
Page 223
Spare Tire Matching Original Equipped Tire wheel, since the wheel is designed specifically WARNING! And Wheel — If Equipped for the collapsible spare tire. Your vehicle may be equipped with a spare tire Compact and collapsible spares are for tem- and wheel equivalent in look and function to the porary emergency use only.
Your wheels are susceptible to deterioration front or rear axle of your vehicle, but it is not. CAUTION! Installation of this limited use spare tire affects caused by salt, sodium chloride, magnesium vehicle handling. Since it is not the same as your chloride, calcium chloride, etc., and other road Do not use scouring pads, steel wool, a original equipment tire, replace (or repair) the...
CAUTION! (Continued) CAUTION! CAUTION! (Continued) • Observe the traction device manufacturer’s SOFT CLOTH. Used on a regular basis; this To avoid damage to your vehicle or tires, is all that is required to maintain this finish. observe the following precautions: instructions on the method of installation, •...
Tire Rotation — Same Tire Size On Front And BODYWORK Body And Underbody Maintenance Rear Axle Cleaning Headlights Protection From Atmospheric The suggested rotation method for vehicles Your vehicle is equipped with plastic headlights Agents equipped with non directional three season and and fog lights that are lighter and less suscep- all season tires is the “forward-cross”...
• Avoid using abrasive compounds and power • If you carry special cargo such as chemicals, Do not remove the belts from the vehicle to buffing that may diminish the gloss or thin out fertilizers, de-icer salt, etc., be sure that such wash them.
Cleaning Plastic Instrument Cluster Lenses NOTE: The lenses in front of the instruments in this If equipped with light colored leather, it tends to vehicle are molded in clear plastic. When clean- show any foreign material, dirt, and fabric dye ing the lenses, care must be taken to avoid transfer more so than darker colors.
IDENTIFICATION DATA WHEEL AND TIRE TORQUE SPECIFICATIONS Vehicle Identification Number Proper lug nut/bolt torque is very important to The Vehicle Identification Number (VIN) is on ensure that the wheel is properly mounted to the the left front corner of the instrument panel. The vehicle.
While operating on gasoline with the required octane number, hearing a light knocking sound from the engine is not a cause for concern. However, if the engine is heard making a heavy knocking sound, see your dealer immediately. Use of gasoline with a lower than recommended octane number can cause engine failure and may void or not be covered by the New Vehicle Limited Warranty.
Ethanol Do Not Use E-85 In Non-Flex Fuel MMT In Gasoline The manufacturer recommends that your ve- Methylcyclopentadienyl Manganese Tricarbonyl Vehicles hicle be operated on fuel containing no more (MMT) is a manganese containing metallic ad- Non-Flex Fuel Vehicles (FFV) are compatible than 15% ethanol.
WARNING! (Continued) WARNING! (Continued) • Do not inhale exhaust gases. They contain • Guard against carbon monoxide with carbon monoxide, a colorless and odorless proper maintenance. Have the exhaust gas, which can kill. Never run the engine in system inspected every time the vehicle is a closed area, such as a garage, and never raised.
CAUTION! CAUTION! (Continued) • Mixing of engine coolant (antifreeze) other • Do not use water alone or alcohol-based than specified Organic Additive Technology engine coolant (antifreeze) products. Do (OAT) engine coolant (antifreeze), may re- not use additional rust inhibitors or antirust sult in engine damage and may decrease products, as they may not be compatible corrosion protection.
The risk of unauthorized and unlawful access to UCONNECT SYSTEMS 2. Press and hold, then drag the selected App your vehicle systems may still exist, even if the to replace an existing shortcut in the main For detailed information about your Uconnect most recent version of vehicle software (such as menu bar.
NOTE: UCONNECT SETTINGS Customer Programmable Features — Uconnect 4C/4C NAV Settings • FCA US LLC or your dealer may contact you The Uconnect system uses a combination of Press the “Apps ” button (if equipped), and buttons on the touchscreen and buttons on the directly regarding software updates.
Page 242
Language After pressing the “Language” button on the touchscreen, the following settings will be avail- able: Setting Name Selectable Options Español/Français/Italiano/ Set Language Brasileiro/Deutsch/English Polski/Portuges/Turk/Pyccknn Nederlands Display After pressing the “Display” button on the touch- screen, the following settings will be available: Setting Name Selectable Options Display Mode...
Page 243
Setting Name Selectable Options Set Theme List Of Options NOTE: When in the “Set Theme” display, you may select the theme for the display screen. To make your selection, press the "Set Theme" button on the touchscreen, then select the desired theme option button until a check-mark appears showing that the setting has been selected. Touchscreen Beep Controls Screen Time-Out —...
Page 244
Voice After pressing the “Voice” button on the touch- screen, the following settings will be available: Setting Name Selectable Options Voice Response Length Brief Detailed Show Command List Never w/Help Always Clock After pressing the “Clock” button on the touch- screen, the following settings will be available: Setting Name Selectable Options...
Page 245
Safety & Driving Assistance After pressing the “Safety & Driving Assistance” button on the touchscreen, the following settings will be available: Setting Name Selectable Options Forward Collision Warning On/Off— If Equipped NOTE: Changing the FCW status to “Off” prevents the system from warning you of a possible collision with the vehicle in front of you. The FCW system state is defaulted to ON from one ignition cycle to the next.
Page 246
Setting Name Selectable Options LaneSense Warning — If Early Medium Late Equipped NOTE: When the “LaneSense Warning” feature is selected, it sets the distance at which the steering wheel will provide feedback for potential lane depar- tures. LaneSense Strength — If Medium High Equipped...
Page 247
Setting Name Selectable Options Electric Power Steering— If Normal Sport Comfort Equipped NOTE: When the “Electric Power Steering Default” is selected, it allows you to change the default setting of your vehicle to either normal, sport, or comfort. Blind Spot Alert — If Equipped Lights Lights &...
Page 248
Setting Name Selectable Options ParkView Backup Camera Active Guidelines — If Equipped NOTE: Your vehicle may be equipped with the ParkView Rear Back Up Camera Active Guidelines that allows you to see active guidelines over the ParkView Back up camera display whenever the gear selector is put into REVERSE. The image will be displayed on the radio touchscreen display along with a caution note to “check entire surroundings”...
Page 249
Lights After pressing the “Lights” button on the touch- screen, the following settings will be available: Setting Name Selectable Options 0 sec 30 sec Headlight Off Delay 60 sec 90 sec 0 sec 30 sec Headlight Illumination On Approach 60 sec 90 sec Headlights With Wipers —...
Page 250
Setting Name Selectable Options Flash Lights With Lock NOTE: When the “Flash Lights With Lock” feature is selected, the exterior lights will flash when the doors are locked or unlocked with the key fob, or when using the passive entry feature. This feature may be selected with or without the “Sound Horn With Lock” feature selected. Sound Horn With Lock 1st Press 2nd Press...
Page 251
Setting Name Selectable Options Personal Settings Linked To Key Fob — If Equipped NOTE: • This feature provides automatic recall of all settings stored to a memory location (driver’s seat, exterior mirrors, steering column position and radio station pre-sets) to enhance driver mobility when entering and exiting the vehicle. •...
Page 252
Engine Off Options After pressing the “Engine Off Options” button on the touchscreen, the following settings will be available: Setting Name Selectable Options Easy Exit Seat — If Equipped NOTE: When the “Easy Exit Seat” feature is selected, the driver’s seat will automatically move rearward once the engine is shut off. 0 sec 45 sec Engine Off Power Delay...
Page 253
Audio After pressing the “Audio” button on the touch- screen, the following settings will be available: Setting Name Selectable Options Balance/Fade “Speaker” Icon Arrow Buttons NOTE: The “Balance/Fade” feature allows you to adjust the Balance and Fade settings. Press and drag the speaker icon, use the arrows to adjust, or tap the “Speaker”...
Page 254
Setting Name Selectable Options AUX Volume Offset — If Equipped NOTE: The “AUX Volume Offset” feature provides the ability to tune the audio level for portable devices connected through the AUX input. To make your se- lection, press the AUX Volume Match button on the touchscreen, choose a level from –3 to +3. Auto Play NOTE: The Auto Play feature allows an media device to begin playing when the media device is plugged in.
Page 255
Setting Name Selectable Options Paired Phones And Audio Sources List Of Paired Phones and Audio Sources NOTE: The “Paired Phones And Audio Sources” feature shows which phones or media devices are paired to the Phone/Bluetooth system. For further infor- mation, refer to the Uconnect Owner’s Manual Supplement. AutoShow Smartphone Display Upon Connection Smartphone Projection Manager...
System Information After pressing the “System Information” button on the touchscreen, the following settings will be available: Setting Name Selectable Options Software License System Software Information Screen NOTE: When the “System Information” feature is selected, a “System Software Information” screen will appear, displaying the system software version. Performance Pages —...
Page 257
The following describes each feature and its 3. After selecting a Widget location: select the NOTE: operation: gauge or timer to display: Pressing the “Camera” icon in the upper right corner of the Performance Pages screen will • Gauge: Oil Temp Home take a screenshot of the current screen and •...
Page 258
• Best • ¼ Mile (400 meter) MPH The “Tickets” contain the timers listed below: • Reaction Time Pressing the “Best” button displays the best Displays the speed the vehicle was at when ¼ recorded run of performance timers, except for mile (400 meters) was reached.
Page 259
• Trans Temp — If Equipped with an Auto- Gauges G-Force matic Transmission Shows the current transmission oil temperature. • Intake Air Temperature Shows the actual air intake temperature. If a gauge is selected, the Gauge Detail View page will appear on the screen. This page shows further information on the selected gauge.
Page 260
• Left G-Forces: • Oil Pressure Engine Measures the right turn force. Shows the actual engine oil pressure. • Rear G-Forces: • Gear Measures the acceleration force. Shows the current (or pending) operating gear of the vehicle. NOTE: Dynamometer (Dyno) Front, Right, Left, and Rear G-Forces are all peak values.
• Pressing the STOP button will freeze the Drive Modes feature is controlled through the Listed below are the available Drive Modes: graph. Selecting Play will clear the graph and Uconnect system and may be accessed by Track Mode restart the process over. performing any of the following: •...
Sport Mode Auto Mode Custom Mode Drive Modes (Sport) Drive Modes (Auto) Custom Mode Pressing the “Sport” button on the touchscreen This mode is for typical driving conditions where The Custom Mode may be selected quickly by will activate the configuration for typical enthu- the Traction and Transmission will be operating pushing the SRT button on the instrument panel siast driving.
Page 263
Drive Mode Set-Up Info Transmission Within the Drive Modes Set-Up screen, press the left / right arrows to scroll through all the available Drive Modes systems giving you a description of their operation and current con- figuration. The last page is a description of the Mode you are currently in.
Page 264
Paddle Shifters Traction Suspension Paddle Shifters Traction Suspension • ON • Track • Track Press the “ON” button on the touchscreen to Press the “Track” button on the touchscreen to Press the “Track” button on the touchscreen to enable steering wheel paddle shifters. modify traction control to optimize track perfor- provide the firmest possible suspension stiff- mance with the least stability control.
Steering — If Equipped RACE OPTIONS Launch Control WARNING! Launch Mode is intended for off-highway or off-road use only and should not be used on any public roadways. It is recommended that this feature be used in a controlled environ- ment, and within the limits of the law.
Shift Light Activate Launch Control Launch RPM Set-Up Launch Control can be accessed by pushing the To adjust the Launch RPM, drag the slider bar or Shift Light Launch Control button on the instrument panel press the arrows on the touchscreen to adjust switch bank or pressing the SRT button on the the holding RPM.
• Traction, steering, and suspension are set to VALET MODE their STREET settings. • Steering wheel paddle shifters are disabled. • The Drive Modes interface is not available. Pressing the SRT button on the touchscreen will display the unlock keypad. •...
ECO MODE STEERING WHEEL AUDIO CONTROLS The remote sound system controls are located on the rear surface of the steering wheel at the three and nine o’clock positions. Valet Mode Deactivation PIN The Valet Mode Deactivation key pad will then prompt you for your four digit PIN code.
The following describes the left-hand control AUX/USB/MP3 CONTROL operation in each mode. This feature allows an external USB device to be plugged into the USB port. Radio Operation For further information, refer to the Uconnect Pushing the top of the switch will “Seek” up for Owner’s Manual Supplement.
UCONNECT VOICE Get Started All you need to control your Uconnect system RECOGNITION QUICK TIPS with your voice are the buttons on your steering wheel. Introducing Uconnect Helpful hints for using Voice Recognition: Start using Uconnect Voice Recognition with these helpful quick tips. It provides the key Voice •...
Radio Push the VR button . After the beep, say one Phone of the following commands and follow the Use your voice to quickly get to the AM or FM Making and answering hands-free phone calls is prompts to switch your media source or choose stations you would like to hear.
Apple iPhone iOS 6 or later supports reading PRE-DEFINED VOICE TEXT REPLY incoming text messages only. To enable this RESPONSES feature on your Apple iPhone, follow these four Stuck in See you simple steps: Yes. traffic. later. Start with- I’ll be late. out me.
. After the beep, say: “Find address 800 hands on the wheel by letting Siri help you Chrysler Drive Auburn Hills, Michigan.” • “Set driver temperature to 20 degrees” perform useful tasks. • “Set 2.
• Text Messages Do Not Disturb Android Auto — If Equipped With Do Not Disturb, you can disable notifica- • Additional Apps NOTE: tions from incoming calls and texts, allowing you Feature availability depends on your carrier and to keep your eyes on the road and hands on the mobile phone manufacturer.
CUSTOMER ASSISTANCE • IF YOU NEED ASSISTANCE ......276...
Page 277
IF YOU NEED ASSISTANCE The manufacturer’s distributors are vitally inter- ested in your satisfaction with their products and services. If a servicing problem or other difficulty should occur, we recommend that you take the following steps: • Discuss the problem at the authorized dealer with the dealer principal or the service man- ager.