Page 1 O W N E R ’ S M A N U A L S R T 8...
Page 2 With respect to any Vehicles Sold in Canada, the name Chrysler This manual illustrates and describes the operation of features and Group LLC shall be deemed to be deleted and the name Chrysler equipment that are either standard or optional on this vehicle. This Canada Inc.
Page 3: Introduction
TABLE OF CONTENTS SECTION PAGE ............3 INTRODUCTION .
Page 5: Table Of Contents
INTRODUCTION CONTENTS Introduction ......4 Vehicle Identification Number ....6 How To Use This Manual .
Page 6: Introduction
4 INTRODUCTION INTRODUCTION When it comes to service, remember that your authorized Congratulations on selecting your new Chrysler Group dealer knows your vehicle best, has factory-trained tech- LLC vehicle. Be assured that it represents precision nicians and genuine MOPAR parts, and cares about workmanship, distinctive styling, and high quality - all your satisfaction.
Page 7 INTRODUCTION 5...
Page 8: Vehicle Identification Number
6 INTRODUCTION WARNINGS AND CAUTIONS This Owner’s Manual contains WARNINGS against op- erating procedures that could result in a collision or bodily injury. It also contains CAUTIONS against proce- dures that could result in damage to your vehicle. If you do not read this entire manual, you may miss important information.
Page 9: Vehicle Modifications/Alterations
INTRODUCTION 7 The vehicle identification number (VIN) is also located VEHICLE MODIFICATIONS/ALTERATIONS on the right front strut tower inside the engine compart- WARNING! ment. Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a collision resulting in serious injury or death.
Page 11 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CONTENTS ▫ Rearming Of The System ....18 A Word About Your Keys ....12 ▫...
Page 12 10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ Programming Additional Transmitters ..24 ▫ Wind Buffeting ..... . . 41 ▫...
Page 13: Safety Checks You Should Make Inside The
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 ▫ Seat Belts And Pregnant Women ..56 Safety Tips ......83 ▫...
Page 14: A Word About Your Keys
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS The Keyless Ignition Node (KIN) has four operating Your vehicle uses a keyless ignition system. This system positions, three of which are labeled and will illuminate consists of a Key Fob with Remote Keyless Entry (RKE) when in position.
Page 15: Key Fob
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 Key Fob The Key Fob also contains the Remote Keyless Entry (RKE) transmitter and an emergency key, which stores in the rear of the Key Fob. The emergency key allows for entry into the vehicle should the battery in the vehicle or the Key Fob go dead.
Page 16: Ignition Or Accessory On Message
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To remove the emergency key, slide the mechanical latch Ignition Or Accessory On Message on the back of the Key Fob sideways with your thumb Opening the driver’s door when the ignition is in ACC or and then pull the key out with your other hand.
Page 17: Sentry Key
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 WARNING! CAUTION! • When leaving the vehicle, always remove the key An unlocked car is an invitation to thieves. Always fob from the ignition and lock your vehicle. remove the Key Fob from vehicle, cycle the ignition •...
Page 18: Replacement Keys
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE After cycling the ignition to the ON/RUN position, the CAUTION! Vehicle Security Light will turn on for three seconds for a bulb check. If the light remains on after the bulb check, it The Sentry Key Immobilizer system is not compat- indicates that there is a problem with the electronics.
Page 19: Customer Key Programming
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 Customer Key Programming CAUTION! Programming Key Fobs or RKE transmitters may be performed at an authorized dealer. Always remove the keys from the vehicle and lock all doors when leaving the vehicle unattended. General Information The Sentry Key system complies with FCC rules Part 15 At the time of purchase, the original owner is provided...
Page 20: Vehicle Security Alarm - If Equipped
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE VEHICLE SECURITY ALARM — IF EQUIPPED To Arm The System The Vehicle Security Alarm monitors the vehicle doors Follow these steps to arm the Vehicle Security Alarm: for unauthorized entry and the ignition switch (and 1.
Page 21: To Disarm The System
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 • Press the LOCK button on the exterior Passive Entry • Cycle the vehicle ignition system out of the OFF Door Handle with a valid FOB available in the same position. exterior zone (refer to Keyless Enter-N-Go in Things To •...
Page 22: Illuminated Entry - If Equipped
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The Vehicle Security Alarm is designed to protect your ILLUMINATED ENTRY — IF EQUIPPED vehicle; however, you can create conditions where the The courtesy lights will turn on when you use the system will give you a false alarm.
Page 23: Remote Keyless Entry (Rke)
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 REMOTE KEYLESS ENTRY (RKE) The RKE system allows you to lock or unlock the doors, open the trunk, or activate the Panic Alarm from dis- tances up to approximately 66 ft (20 m) using a hand-held Key Fob with RKE transmitter.
Page 24: To Lock The Doors
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If the vehicle is equipped with Passive Entry, refer to Turn Headlights On With Remote Key Unlock “Keyless Enter-N-Go” under “Things To Know Before This feature activates the headlights for up to 90 seconds Starting Your Vehicle”...
Page 25: To Unlatch The Trunk
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 Sound Horn With Remote Key Lock headlights will turn on, the park lights will flash, the This feature will cause the horn to chirp when the doors horn will pulse on and off, and the interior lights will are locked with the RKE transmitter.
Page 26: Transmitter Battery Replacement
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Programming Additional Transmitters 2. Insert the tip of the emergency key or a #2 flat blade Programming Key Fobs or RKE transmitters may be screwdriver into the slot and gently pry the two halves of performed at an authorized dealer.
Page 27: General Information
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 When replacing the battery, match the + sign on the battery If your RKE transmitter fails to operate from a normal to the + sign on the inside of the battery clip, located on the distance, check for these two conditions: back cover.
Page 28: How To Use Remote Start
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE How To Use Remote Start WARNING! All of the following conditions must be met before the • Do not start or run an engine in a closed garage or engine will remote start: confined area.
Page 29 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 Remote Start Abort Message On Electronic Vehicle To Enter Remote Start Mode Information Center (EVIC) — If Equipped Press and release the REMOTE START button The following messages will display in the EVIC if the on the RKE transmitter twice within five sec- vehicle fails to remote start or exits remote start prema- onds.
Page 30: Door Locks
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • For security, power window and power sunroof op- To Exit Remote Start Mode And Drive The Vehicle eration (if equipped) are disabled when the vehicle is Before the end of 15 minute cycle, press and release the in the Remote Start mode.
Page 31 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 WARNING! • For personal security and safety in the event of an accident, lock the vehicle doors before you drive as well as when you park and leave the vehicle. • Never leave children alone in a vehicle, or with access to an unlocked vehicle.
Page 32: Power Door Locks
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Power Door Locks The doors can also be locked and unlocked with the A power door lock switch is on each front door trim Keyless Enter-N-Go (Passive Entry) system. For further panel. Use this switch to lock or unlock the doors. information, refer to “Keyless Enter-N-Go”...
Page 33 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 Automatic Door Locks — If Equipped 3. The transmission is in NEUTRAL or PARK. The auto door lock feature default condition is enabled. 4. The driver door is opened. When enabled, the door locks will lock automatically when the vehicle’s speed exceeds 15 mph (24 km/h).
Page 34: Child-Protection Door Lock System - Rear Doors
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Child-Protection Door Lock System — Rear Doors To provide a safer environment for small children riding in the rear seats, the rear doors are equipped with Child-Protection Door Lock system. To Engage Or Disengage The Child-Protection Door Lock System 1.
Page 35: Keyless Enter-N-Go
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 KEYLESS ENTER-N-GO™ WARNING! The Passive Entry system is an enhancement to the vehicle’s Remote Keyless Entry (RKE) system and a Avoid trapping anyone in a vehicle in a collision. feature of Keyless Enter-N-Go™. This feature allows you Remember that the rear doors can only be opened to lock and unlock the vehicle’s door(s) without having to from the outside when the Child-Protection locks are...
Page 36 34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Unlock From The Driver’s Side: NOTE: If “Unlock All Doors 1st Press” is programmed With a valid Passive Entry RKE transmitter within 5 ft all doors will unlock when you grab hold of the front (1.5 m) of the driver’s door handle, grab the front driver driver’s door handle.
Page 37 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 Preventing Inadvertent Locking Of Passive Entry RKE NOTE: The vehicle will only unlock the doors when the Transmitter In Vehicle doors are locked using the door panel switch, a valid To minimize the possibility of unintentionally locking a Passive Entry RKE transmitter is detected inside the Passive Entry RKE transmitter inside your vehicle, the vehicle, and no valid Passive Entry RKE transmitter is...
Page 38 36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Enter The Trunk NOTE: If you inadvertently leave your vehicle’s Passive With a valid Passive Entry RKE transmitter within 3 ft Entry RKE transmitter in the trunk and try to close the (1.0 m) of the deck lid, press the button on the right side deck lid, the deck lid will automatically unlatch, unless of CHMSL, (Center High Mounted Stop Light) which is...
Page 39 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 To Lock The Vehicle’s Doors NOTE: • After pressing the door handle LOCK button, you With one of the vehicle’s Passive Entry RKE transmitters within 5 ft (1.5 m) of the driver or passenger front door must wait two seconds before you can lock or unlock handles, press the door handle LOCK button to lock all the doors, using either Passive Entry door handle.
Page 40: Windows
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WINDOWS The window controls will operate only when the ignition switch is in the ACC or ON/RUN position. Power Windows The window controls on the driver’s door control all the NOTE: For vehicles equipped with the Uconnect door windows.
Page 41 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 AUTO-Down Feature To close the window part way, lift the window switch to The driver door power window switch and some model the first detent and release it when you want the window passenger door power window switches have an AUTO- to stop.
Page 42 40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Reset Auto Up (setting it in the DOWN position). To enable the window Should the Auto Up feature stop working, the window controls and the rear sunscreen, press and release the probably needs to be reset. To reset Auto Up: window lockout button again (setting it in the UP position).
Page 43: Wind Buffeting
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 Wind Buffeting The trunk lid can be released from outside the vehicle by pressing the Wind buffeting can be described as the perception of TRUNK button on the Remote pressure on the ears or a helicopter-type sound in the Keyless Entry (RKE) transmitter ears.
Page 44: Trunk Safety Warning
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE TRUNK SAFETY WARNING Trunk Emergency Release As a security measure, a trunk internal emergency release WARNING! lever is built into the trunk latching mechanism. In the event of an individual being locked inside the trunk, the Do not allow children to have access to the trunk, trunk can be simply opened by pulling on the glow-in-the- either by climbing into the trunk from outside, or...
Page 45: Occupant Restraints
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 • Knee bolsters/blockers for front seat occupant OCCUPANT RESTRAINTS Some of the most important safety features in your • Front seat belts incorporate pretensioners that may vehicle are the restraint systems: enhance occupant protection by managing occupant •...
Page 46 44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: The Advanced Front Air Bags have a multistage Children that are not big enough to wear the vehicle seat inflator design. This allows the air bag to have different belt properly (see section on Child Restraints) should be rates of inflation based on several factors, including the secured in the rear seat in child restraints or belt- severity and type of collision.
Page 47 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 3. The driver and front passenger seats should be WARNING! moved back as far as practical to allow the Advanced • Relying on the air bags alone could lead to more Front Air Bags room to inflate. severe injuries in a collision.
Page 48 46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Buckle up even though you are an excellent driver, even WARNING! (Continued) on short trips. Someone on the road may be a poor driver • Supplemental Side Air Bag Inflatable Curtain and cause a collision that includes you. This can happen (SABIC) and Seat-Mounted Side Air Bags (SAB) far away from home or on your own street.
Page 49: Lap/Shoulder Belts
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 Lap/Shoulder Belts WARNING! (Continued) All seating positions in your vehicle are equipped with • Wearing a seat belt incorrectly is dangerous. Seat lap/shoulder belts. belts are designed to go around the large bones of The belt webbing retractor is designed to lock during your body.
Page 50 48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lap/Shoulder Belt Operating Instructions 2. The seat belt latch plate is above the back of your seat. Grasp the latch plate and pull out the belt. Slide the latch 1. Enter the vehicle and close the door. Sit back and plate up the webbing as far as necessary to make the belt adjust the front seat.
Page 51 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 WARNING! WARNING! (Continued) • A belt that is worn under your arm is dangerous. • A belt that is buckled into the wrong buckle will Your body could strike the inside surfaces of the not protect you properly.
Page 52 50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Position the lap belt across your thighs, below your WARNING! abdomen. To remove slack in the lap belt portion, pull up • A lap belt worn too high can increase the risk of a bit on the shoulder belt.
Page 53 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 6. To release the belt, push the red button on the buckle. Adjustable Upper Shoulder Belt Anchorage The belt will automatically retract to its stowed position. In the driver and front passenger seats, the shoulder belt If necessary, slide the latch plate down the webbing to can be adjusted upward or downward to position the belt allow the belt to retract fully.
Page 54: Lap/Shoulder Belt Untwisting Procedure
52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE As a guide, if you are shorter than average you will 3. Slide the latch plate upward over the folded webbing. The folded webbing must enter the slot at the top of the prefer a lower position, and if you are taller than average latch plate.
Page 55: Automatic Locking Retractor Mode (Alr) - If Equipped
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 If the passenger seating position is equipped with an position that has a belt with this feature. Children ALR and is being used for normal usage: 12 years old and under should always be properly restrained in the rear seat.
Page 56: Energy Management Feature
54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Seat Belt Pretensioner WARNING! The seat belts for both front seating positions are • The belt and retractor assembly must be replaced equipped with pretensioning devices that are designed to remove slack from the seat belt in the event of a collision. if the seat belt assembly Automatic Locking Re- These devices may improve the performance of the seat tractor (ALR) feature or any other seat belt func-...
Page 57: Enhanced Seat Belt Use Reminder System (Beltalert )
5 mph (8 km/h), by blinking the Seat Belt BeltAlert can be enabled or disabled by your authorized Reminder Light and sounding an intermittent chime. dealer. Chrysler Group LLC does not recommend deac- Once the sequence starts, it will continue for the entire tivating BeltAlert .
Page 58: Seat Belts And Pregnant Women
56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Seat Belts And Pregnant Women WARNING! We recommend that pregnant women use the seat belts throughout their pregnancy. Keeping the mother safe is Using a seat belt extender when not needed can the best way to keep the baby safe.
Page 59 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 In addition, the vehicle is equipped with a Supplemental NOTE: The Driver and Front Passenger Advanced Front Driver Side Knee Air Bag mounted in the instrument Air Bags are certified to the new Federal regulations for panel below the steering column.
Page 60 58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE This vehicle is equipped with Supplemental Side Air Bag Air Bag System Components Inflatable Curtains (SABIC) to protect the driver, front, Your vehicle may be equipped with the following air bag and rear passengers sitting next to a window. The SABIC system components: air bags are located above the side windows and their •...
Page 61 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 • Front and Side Impact Sensors WARNING! • Front Seat Belt Pretensioners, Seat Belt Buckle Switch, • No objects should be placed over or near the air bag and Seat Track Position Sensors on the instrument panel, because any such objects Advanced Front Air Bag Features could cause harm if the vehicle is in a collision...
Page 62 60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Supplemental Seat-Mounted Side Air Bags (SAB) When the air bag deploys, it opens the seam between the Supplemental Seat-Mounted Side Air Bags (SAB) may front and side of the seat’s trim cover. Each air bag provide enhanced protection to help protect an occupant deploys independently;...
Page 63 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 The system includes side impact sensors that are cali- brated to deploy the side air bags during impacts that require air bag occupant protection. WARNING! • Your vehicle is equipped with left and right Supplemental Side Air Bag Inflatable Curtain (SABIC), do not stack luggage or other cargo up high enough to block the location of the SABIC.
Page 64: Air Bag Deployment Sensors And Controls
62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Supplemental Driver Side Knee Air Bag Air Bag Deployment Sensors And Controls The Supplemental Driver Side Knee Air Bag provides Occupant Restraint Controller (ORC) enhanced protection and works together with the Driver The ORC is part of a Federally regulated safety system Advanced Front Air Bag during a frontal impact.
Page 65 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 The Advanced Front Air Bags and Supplemental Driver Seat belts are necessary for your protection in all colli- Side Knee Air Bag will not deploy in all frontal collisions, sions, and also are needed to help keep you in position, including some that may produce substantial vehicle away from an inflating air bag.
Page 66 64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE turns on the Air Bag Warning Light, either momentarily Driver And Passenger Advanced Front Air Bag or continuously. A single chime will sound if the light Inflator Units comes on again after initial startup. The Driver and Passenger Advanced Front Air Bag Inflator Units are located in the center of the steering It also includes diagnostics that will illuminate the instru-...
Page 67 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 The Advanced Front Air Bag gas is vented through the Supplemental Seat-Mounted Side Air Bag (SAB) vent holes in the sides of the air bag. In this way, the air Inflator Units bags do not interfere with your control of the vehicle.
Page 68 66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Supplemental Side Air Bag Inflatable Curtain Because air bag sensors estimate deceleration over time, (SABIC) Inflator Units vehicle speed and damage are not good indicators of During collisions where the impact is confined to a whether or not an air bag should have deployed.
Page 69 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67 • Turn on the interior lights, which remain on as long as If you do have a collision which deploys the air bags, any the battery has power, until the ignition key is re- or all of the following may occur: moved or the ignition switch is changed to OFF using •...
Page 70 68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE throat irritation, move to fresh air. If the irritation Maintaining Your Air Bag System continues, see your doctor. If these particles settle on WARNING! your clothing, follow the garment manufacturer’s in- structions for cleaning. •...
Page 71 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69 Air Bag Warning Light WARNING! (Continued) You will want to have the air bags ready to • Do not attempt to modify any part of your air bag inflate for your protection in a collision. The system.
Page 72: Event Data Recorder (Edr)
70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: If the speedometer, tachometer, or any engine vehicle dynamics and safety systems for a short period of related gauges are not working, the Occupant Restraint time, typically 30 seconds or less. The EDR in this vehicle Controller (ORC) may also be disabled.
Page 73: Child Restraints
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 71 NOTE: EDR data are recorded by your vehicle only if a Child Restraints non-trivial crash situation occurs; no data are recorded by Everyone in your vehicle needs to be buckled up all the the EDR under normal driving conditions and no per- time, including babies and children.
Page 74 72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Infants And Child Restraints WARNING! Safety experts recommend that children ride rearward- facing in the vehicle until they are two years old or until In a collision, an unrestrained child, even a tiny baby, they reach either the height or weight limit of their rear can become a projectile inside the vehicle.
Page 75 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 73 held in the vehicle by the lap/shoulder belt or the have outgrown the rear-facing weight or height limit of LATCH child restraint anchor system. Refer to “Lower their rear-facing convertible child seat. Children should Anchors and Tether for CHildren (LATCH)”.
Page 76 74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Children Too Large For Booster Seats NOTE: For additional information, refer to Children who are large enough to wear the shoulder belt www.seatcheck.org or call 1–866–SEATCHECK. Cana- comfortably and whose legs are long enough to bend dian residents should refer to Transport Canada’s web- over the front of the seat when their back is against the site for additional information: http://www.tc.gc.ca/...
Page 77 Safety vehicle. Do not leave it loose in the vehicle. In a Standards. Chrysler Group LLC also recommends that sudden stop or accident, it could strike the occupants you make sure that you can install the child restraint in or seatbacks and cause serious personal injury.
Page 78 76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE LATCH-compatible child restraint systems are now avail- anchorage. If installing child seats in adjacent rear- able. However, because the lower anchorages are to be seating positions, or if your child restraints are not introduced over a period of years, child restraint systems LATCH-compatible, install the restraints using the vehi- having attachments for those anchorages will continue to...
Page 79 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 77 Installing The LATCH-Compatible Child Restraint In addition, there are tether strap anchorages System behind each rear seating position located in the We urge you to follow the manufacturer’s directions panel between the rear seatback and the rear carefully when installing your child restraint.
Page 80 78 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE You will first loosen the child seat adjusters on the lower For center seating position route the tether strap over the straps and on the tether strap so that you can more easily seatback and adjustable headrest (with the headrest in attach the hooks or connectors to the vehicle anchorages.
Page 81 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 79 NOTE: • Ensure that the tether strap does not slip into the opening between the seatbacks as you remove slack in the strap. • When using the LATCH attaching system to install a child restraint, please ensure that all seat belts not being used for occupant restraints are stowed and out of reach of children.
Page 82 80 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE necessary to use a locking clip. The ALR will make a WARNING! ratcheting noise if you extract the entire belt from the retractor and then allow the belt to retract into the Improper installation of a child restraint to the retractor.
Page 83 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 81 1. To install a child restraint with ALR, first, pull enough To attach a child restraint tether strap: of the seat belt webbing from the retractor to route it 1. Rotate the cover over the anchor directly behind the through the belt path of the child restraint.
Page 84: Engine Break-In Recommendations
82 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. Route the tether strap to provide the most direct path Transporting Pets for the strap between the anchor and the child seat. Air Bags deploying in the front seat could harm your pet. An unrestrained pet will be thrown about and possibly 3.
Page 85: Safety Tips
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 83 The engine oil, transmission fluid, and axle lubricant SAFETY TIPS installed at the factory is high-quality and energy- Transporting Passengers conserving. Oil, fluid, and lubricant changes should be NEVER TRANSPORT PASSENGERS IN THE CARGO consistent with anticipated climate and conditions under AREA.
Page 86: Exhaust Gas
84 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Exhaust Gas WARNING! (Continued) • If it is necessary to sit in a parked vehicle with the WARNING! engine running, adjust your heating or cooling Exhaust gases can injure or kill. They contain carbon controls to force outside air into the vehicle.
Page 87: Safety Checks You Should Make Inside The Vehicle
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 85 Safety Checks You Should Make Inside The Defroster Vehicle Check operation by selecting the defrost mode and place the blower control on high speed. You should be able to Seat Belts feel the air directed against the windshield. See your Inspect the belt system periodically, checking for cuts, authorized dealer for service if your defroster is frays, and loose parts.
Page 88 86 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! WARNING! (Continued) • Check mounting of mats on a regular basis. Always Pedals that cannot move freely can cause loss of properly reinstall and secure floor mats that have vehicle control and increase the risk of serious per- been removed for cleaning.
Page 89: Periodic Safety Checks You Should Make Outside The Vehicle
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 87 Periodic Safety Checks You Should Make Outside Door Latches The Vehicle Check for positive closing, latching, and locking. Tires Fluid Leaks Examine tires for excessive tread wear and uneven wear Check area under vehicle after overnight parking for fuel, patterns.
Page 91 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS ▫ Power Mirrors ..... . . 99 Mirrors ......96 ▫...
Page 92 90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Uconnect™ Phone (8.4/8.4N) ... . . 110 Seats ......161 ▫...
Page 93 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 91 ▫ Turn Signals ......186 To Open And Close The Hood ... . 179 ▫...
Page 94 92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Headlights On With Wipers (Available With ▫ To Accelerate For Passing ....204 Automatic Headlights Only) ... . 193 Adaptive Cruise Control (ACC) —...
Page 95 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 93 ▫ Display Warnings And Maintenance ..219 ▫ Cleaning The Parksense System ..238 ▫ Precautions While Driving With ACC ..222 ▫...
Page 96 94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Canadian/Gate Operator Programming ..251 ▫ Wind Buffeting ..... . 257 ▫...
Page 97 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 95 ▫ Pinch Protect Feature ....261 ▫ Door Storage ..... . . 272 ▫...
Page 98: Mirrors
96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS Automatic Dimming Mirror This mirror automatically adjusts for headlight glare from vehicles behind you. This feature will be defaulted on, and only be disabled when the vehicle is moving in reverse. NOTE: This feature is disabled when the vehicle is moving in reverse.
Page 99: Outside Mirrors
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 97 Outside Mirrors Outside Mirrors Folding Feature — If Equipped To receive maximum benefit, adjust the outside mirror(s) Some models have outside mirrors that are hinged. The to center on the adjacent lane of traffic and a slight hinge allows the mirror to pivot forward and rearward to overlap of the view obtained from the inside mirror.
Page 100: Outside Mirrors With Turn Signal And Approach Lighting - If Equipped
98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Outside Mirrors With Turn Signal And Approach NOTE: The approach lighting will not function when Lighting — If Equipped the shift lever is moved out of the PARK position. Driver and passenger outside mirrors with turn signal Tilt Mirrors In Reverse —...
Page 101: Power Mirrors
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 99 Power Mirrors The power mirror controls consist of mirror select but- The power mirror controls are located on the driver’s tons and a four-way mirror control switch. To adjust a door trim panel. mirror, press either the L (left) or R (right) to select button the mirror that you want to adjust.
Page 102: Power Folding Outside Mirrors - If Equipped
100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Power Folding Outside Mirrors — If Equipped Illuminated Vanity Mirrors — If Equipped The switch for the power folding mirrors is located An illuminated vanity mirror is located on the sun visor. between the power mirror switches L (left) and R (right). To use the mirror, rotate the sun visor downward and Press the switch once and the mirrors will fold in, swing the mirror cover upward.
Page 103: Slide-On-Rod" And Extender Features Of Sun Visor
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 101 “Slide-On-Rod” And Extender Features Of Sun Visor To use the “Slide-On-Rod” feature of the sun visor, rotate the sun visor downward and swing the sun visor so it is parallel to the side window, grabbing the sun visor with your left hand pull rearwards until the sun visor is in the desired position.
Page 104: Blind Spot Monitoring - If Equipped
102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE BLIND SPOT MONITORING — IF EQUIPPED When the vehicle is started, the BSM warning light will The Blind Spot Monitoring (BSM) system uses two radar- momentarily illuminate in both outside rear view mirrors based sensors, located inside the rear bumper fascia, to to let the driver know that the system is operational.
Page 105 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103 The BSM detection zone covers approximately one lane beyond the side of your vehicle, this may result in the on both sides of the vehicle (11 ft or 3.35 m). The zone BSM warning light remaining illuminated the entire starts at the outside rear view mirror and extends ap- time the vehicle is in a forward gear.
Page 106 104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Entering From The Side Entering From The Rear Vehicles that move into your adjacent lanes from either Vehicles that come up from behind your vehicle on either side of the vehicle. side and enter the rear detection zone with a relative speed of less than 30 mph (48 km/h).
Page 107 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105 Overtaking Traffic If you pass another vehicle slowly (with a relative speed of less than 10 mph (16 km/h) and the vehicle remains in the blind spot for approximately 1.5 seconds, the warning light will be illuminated.
Page 108 106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The BSM system is designed not to issue an alert on The BSM system will not alert you of objects that are stationary objects such as guardrails, posts, walls, foliage, traveling in the opposite direction of the vehicle in berms, etc.
Page 109: Rear Cross Path
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107 WARNING! The Blind Spot Monitoring system is only an aid to help detect objects in the blind spot zones. The BSM system is not designed to detect pedestrians, bicy- clists, or animals. Even if your vehicle is equipped with the BSM system, always check your vehicle’s mirrors, glance over your shoulder, and use your turn signal before changing lanes.
Page 110: Modes Of Operation
108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: In a parking lot situation, oncoming vehicles can Modes Of Operation be obscured by vehicles parked on either side. If the Three selectable modes of operation are available in the sensors are blocked by other structures or vehicles, the Uconnect Touch™...
Page 111 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 alert present on that side of the vehicle, an audible chime Blind Spot Alert Off will also be sounded. Whenever a turn signal and de- When the BSM system is turned off, there will be no tected object are present on the same side at the same visual or audible alerts from either the BSM or RCP time, both the visual and audio alerts will be issued.
Page 112: Understanding The Features Of Your Vehicle
110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Calling Back the last incoming call number (“Call Uconnect™ Phone (8.4/8.4N) Back”). Uconnect Touch™ 8.4/8.4 Nav • View Call logs on screen (“Show incoming calls”, Uconnect™ Phone is a voice-activated, hands-free, in- vehicle communications system.
Page 113 Bluetooth “Hands-Free Profile” mobile phone. • www.chrysler.com/uconnect Uconnect™ features Bluetooth technology - the global standard that enables different electronic devices to con- • www.dodge.com/uconnect nect to each other without wires or a docking station, so • www.jeep.com/uconnect Uconnect™ Phone works no matter where you stow your •...
Page 114 112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE long as your phone is turned on and has been paired to Uconnect™ Voice Command Button the vehicle’s Uconnect™ Phone. The Uconnect™ Phone The Uconnect™ Voice Command Button allows up to ten mobile phones or audio devices to be is only used for “barge in”...
Page 115: Operation
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 • For certain operations, compound commands can be Operation Voice commands can be used to operate the Uconnect™ used. For example, instead of saying “Call” and then Phone and to navigate through the Uconnect™ Phone “John Smith”...
Page 116 114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Natural Speech Voice Command Tree Your Uconnect™ Phone Voice system uses a Natural Refer to “Voice Tree” in this section. Language Voice Recognition (VR) engine. Help Command Natural speech allows the user to speak commands in If you need assistance at any prompt, or if you want to phrases or complete sentences.
Page 117 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 NOTE: Pressing the buttons while the 1. Press the “Phone” soft-key on the screen to begin. system is playing is known as “Barging In”, refer to 2. If there is no phone currently connected with the “Barge —...
Page 118 116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Select Yes to begin the pairing process. Then, search for available devices on your Bluetooth enabled mobile phone. When prompted on the phone, enter the name and PIN shown on the Uconnect Touch™ screen. •...
Page 119 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 Pair Additional Mobile Phones • Touch the “More” soft-key to begin, • Touch the “Settings” soft-key, • Next, touch the “Phone/Bluetooth ” soft-key, • Touch the “Add Device” soft-key, • Search for available devices on your Bluetooth en- abled mobile phone.
Page 120 118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Uconnect™ Phone will display an in process screen You can also use the following VR commands to bring up the Paired Phone screen from any screen on the radio: while the system is connecting, •...
Page 121 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 • Touch the + soft-key located to the right of the device Connecting To A Particular Mobile Phone Or Audio Device name, Uconnect™ Phone will automatically connect to the • The options pop-up will be displayed, highest priority paired phone and/or Audio Device •...
Page 122 120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Making A Phone Or Audio Device A Favorite phonebook. Specific Bluetooth Phones with Phone Book Access Profile may support this feature. See Uconnect™ • Touch the “Settings” soft-key, website for supported phones. • Touch the “Phone/Bluetooth ” soft-key, •...
Page 123 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 • Only the phonebook of the currently connected mobile 2. After loading the mobile phonebook, select phone- phone is accessible. book from the Phone main screen, then select the appro- priate number. Touch the + next to the selected number to •...
Page 124 122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: If the Favorites list is full, you will be asked to remove an existing favorite. 3. From the Phone main screen, select phonebook. From the phonebook screen, select the “Favorites” soft-key and then select the + soft-key located to the right of the phonebook record.
Page 125 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 • Touch the + next to the Favorite you would like to Emergency And Towing Assistance remove. The Emergency and Towing Favorite numbers can only be altered. These cannot be deleted and the names cannot be changed.
Page 126: Phone Call Features
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Touch the + next to appropriate Favorite that is to be Phone Call Features altered. The following features can be accessed through the Uconnect™ Phone if the feature(s) are available and sup- ported by Bluetooth on your mobile service plan.
Page 127 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 • Recent Call Log • The Uconnect™ Phone will dial the number associated with John Doe, or if there are multiple numbers it will • SMS Message Viewer ask which number you want to call for John Doe. NOTE: All of the above operations except Redial can be Call Controls done with 1 call or less active.
Page 128 126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Touch-Tone Number Entry Recent Calls You may browse up to 34 of the most recent of each of the • Touch the “Phone” soft-key, following call types: • Touch the “Dial” soft-key, • The Touch-Tone screen will be displayed, •...
Page 129 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 These can be accessed by touching the “recent calls” Answer Or Ignore An Incoming Call — Call soft-key on the Phone main screen. Currently In Progress If a call is currently in progress and you have another You can also press the button and say “Show my incoming call, you will hear the same network tones for...
Page 130 128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Making A Second Call While Current Call Is In Toggling Between Calls Progress If two calls are in progress (one active and one on hold), To make a second call while you are currently on a call, touch the “Swap”...
Page 131: Uconnect™ Phone Features
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 Redial Uconnect™ Phone Features • Press the “Redial” soft-key, Emergency Assistance If you are in an emergency and the mobile phone is • or press the and after the “Listening” prompt and reachable: the following beep, say “Redial”, •...
Page 132 2069 for the U.S., 1-877-213-4525 for Canada, 55-14- WARNING! 3454 for Mexico City and 1-800-712-3040 for outside Mexico City in Mexico). Please refer to the Chrysler Your phone must be turned on and connected to the Group LLC 24-Hour “Towing Assistance” coverage Uconnect™...
Page 133 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 Voice Mail Calling then the sequence you wish to enter. For example, if To learn how to access your voice mail, refer to “Working required to enter your PIN followed with a pound, (3 7 4 6 #), you can press the button and say, “Send 3 7 with Automated Systems”.
Page 134 132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Barge In — Overriding Prompts • The first number encountered for that contact will be button can be used when you wish to skip part sent. All other numbers entered for that contact will be of a prompt and issue your voice command immediately.
Page 135 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 Phone And Network Status Indicators NOTE: Certain brands of mobile phones do not send the Uconnect™ Phone will provide notification to inform dial ring to the Uconnect™ Phone to play it on the vehicle you of your phone and network status when you are audio system, so you will not hear it.
Page 136: Advanced Phone Connectivity
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Advanced Phone Connectivity Things You Should Know About Your Uconnect™ Phone Transfer Call To And From Mobile Phone The Uconnect™ Phone allows ongoing calls to be trans- Voice Command ferred from your mobile phone to the Uconnect™ Phone •...
Page 137 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 • Performance is maximized under: • Storing names in your favorites phonebook when the vehicle is not in motion is recommended. • low-to-medium blower setting, • Phonebook (Mobile and Favorites) name recognition • low-to-medium vehicle speed, rate is optimized when the entries are not similar.
Page 138 136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Performance, such as audio clarity, echo, and loudness Far End Audio Performance to a large degree rely on the phone and network, and • Audio quality is maximized under: not the Uconnect™ Phone. •...
Page 139 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 Uconnect™ Phone can read or send new messages on your phone. Your phone must support SMS over Bluetooth in order to use this feature. If the Uconnect™ Phone determines your phone is not compatible with SMS messaging over Bluetooth the “Messaging”...
Page 140 138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Read Messages: Once a message is received and viewed or listened to, you will have the following options: If you receive a new text message while your phone is • Send a Reply connected to Uconnect™...
Page 141 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139 Send Messages Using Voice Commands: • Press the button, • After the “Listening” prompt and the following beep, say “Send message to John Smith mobile”, • After the system prompts you for what message you want to send, say the message you wish to send or say “List”.
Page 142 140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE After the system confirms that you want to send your 3. Okay. message to John Smith, your message will be sent. 4. I can’t talk right now. 5. Call me. 6. I’ll call you later. 7.
Page 143 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 14. Where are you? Bluetooth Communication Link Mobile phones have been found to lose connection to the 15. Are you there yet? Uconnect™ Phone. When this happens, the connection 16. I need directions. can generally be reestablished by switching the phone OFF/ON.
Page 144 142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Voice Tree...
Page 145 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 • You can replace “248 555 1212” with any phone NOTE: • You can replace “John Smith” with any name in your number supported by your Mobile phone. mobile or favorite phone book. You can also say “Send •...
Page 146 144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 147 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 • You can replace “248 555 1212” with any phone NOTE: • You can replace “John Smith” with any name in your number supported by your Mobile phone. mobile or favorite phone book. You can also say “Send •...
Page 148: General Information
146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE General Information VOICE COMMAND This device complies with Part 15 of the FCC rules and Uconnect Touch™ 8.4/8.4 Nav RSS 210 of Industry Canada. Operation is subject to the The Uconnect™ Voice Command system allows following conditions: you to control your AM, FM radio, satellite •...
Page 149 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 When you press the Uconnect™ Voice Command NOTE: At any time, you can say the words “Cancel” or button, you will hear a beep. The beep is your signal to “Help”. give a command. These commands are universal and can be used from any If no command is spoken the system will say one of two menu.
Page 150: Uconnect™ Voice Commands
148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Natural Speech The system utilizes continuous dialog; when the system Natural speech allows the user to speak commands in requires more information from the user it will ask a phrases or complete sentences. The system filters out question to which the user can respond without pressing certain non-word utterances and sounds such as “ah”...
Page 151 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 Changing the Volume Starting Voice Recognition (VR) Session in Radio/Player Modes 1. Start a dialogue by pressing the Voice Command In this mode, you can say the following commands: button. NOTE: The commands can be said on any screen when 2.
Page 152: Voice Tree
150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Voice Tree...
Page 153 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 NOTE: 1. You can replace “950 AM” with any other AM or FM frequency, such as “98.7 FM”. 2. You can replace “80’s on 8” with any other satellite station name received by the radio. 3.
Page 154 152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 155 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153 NOTE: 1. You can replace the album, artist, song, genre, playlist, podcast and audio book names with any corresponding names on the current device that is playing. 2. You can replace “8” with any track on the CD that is currently playing.
Page 156 154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 157 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155 NOTE: 1. You can replace “NFL” with any league shown on the sports league screen. For example you can say “Show MLB headlines” or “Show PGA headlines”. 2. You can replace “Headlines” with any menu items shown on a league screen.
Page 158 156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 159 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157 NOTE: 1. Only available with Navigation equipped vehicles. 2. You can replace “Player” with “Radio”, “Navigation”, “Phone”, “Climate”, “More” or “Settings”. 3. Navigation commands only work if equipped with Navigation. 4. Available Voice Commands are shown in bold face and shaded grey.
Page 160 158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 161 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 159 NOTE: 1. You can also say “Find City”, “Find Favorite”, “Find Play by Category”, “Find Play by Name”, “Find Recently Found”, “Where to?” or “Go Home”. 2. You can say “Find Nearest” then “Restaurant”, “Fuel”, “Transit”, “Lodging”, “Shopping”, “Bank”, “Entertain- ment”, “Recreation”, “Attractions”, “Community”, “Auto Services”, “Hospitals”, “Parking”, “Airport”, “Police Sta-...
Page 162 160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 163: Seats
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 161 NOTE: Available Voice Commands are shown in bold SEATS face and shaded grey. Seats are a part of the Occupant Restraint System of the vehicle. WARNING! • It is dangerous to ride in a cargo area, inside or outside of a vehicle.
Page 164: Power Seats
162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Power Seats The power seat switch is located on the outboard side of the seat near the floor. Use this switch to move the driver’s seat up or down, forward or rearward or to recline the seatback.
Page 165 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 163 Adjusting The Seat Forward Or Rearward Reclining The Seatback The seat can be adjusted both forward and rearward. The angle of the seatback can be adjusted forward or Push the seat switch forward or rearward, the seat will rearward.
Page 166: Power Lumbar
164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! Do not place any article under a power seat or impede its ability to move as it may cause damage to the seat controls. Seat travel may become limited if movement is stopped by an obstruction in the seat’s path.
Page 167: Heated Seats
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165 Heated Seats WARNING! (Continued) On some models, the front and rear seats may be • Do not place anything on the seat that insulates equipped with heaters in both the seat cushions and against heat, such as a blanket or cushion.
Page 168 166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Front Heated Seat Operations — Uconnect Touch™ Press the “Driver” or “Passenger” seat soft-key once to 8.4 and 8.4 Nav: select HI-level heating. Press the soft-key a second time Press the “Controls” soft-key located on the bottom of the to select LO-level heating.
Page 169 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167 NOTE: Once a heat setting is selected, heat will be felt Rear Heated Seats within two to five minutes. On vehicles equipped with rear heated seats, the seats closest to the doors are heated. The controls for these When the HI-level setting is selected, the heater will seats are located on the rear of the center console.
Page 170: Ventilated Seats - If Equipped
168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE one, indicating the change. Operation on the LO-level Front Ventilated Seat Operation — Uconnect setting also turns OFF automatically after approximately Touch™ 8.4/8.4 Nav: 30 minutes. Press the “Controls” soft-key located on the bottom of the Uconnect Touch™...
Page 171 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 169 Press the “Driver” or “Passenger” seat soft-key once to NOTE: The engine must be running for the ventilated select HI-level ventilation. Press the soft-key a second seats to operate. time to select LO-level ventilation. Press the soft-key a Vehicles Equipped With Remote Start third time to shut off the seat ventilation.
Page 172: Head Restraints
170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Head Restraints Active Head Restraints — Front Seats Head restraints are designed to reduce the risk of injury The front driver and passenger seats are equipped with by restricting head movement in the event of a rear Active Head Restraints (AHR).
Page 173 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 171 To raise the head restraint, pull upward on the head NOTE: The head restraints should only be removed by restraint. To lower the head restraint, press the push qualified technicians, for service purposes only. If either button, located at the base of the head restraint, and push of the head restraints require removal, see your autho- downward on the head restraint.
Page 174 172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Head Restraints The center head restraint has two positions, up or down. When the center seat is being occupied the head restraint should be in the raised position. When there are no occupants in the center seat the head restraint can be lowered for maximum visibility for the driver.
Page 175: Folding Rear Seat
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 173 Folding Rear Seat After releasing the seatback, it can be folded forward. The rear seatbacks can be folded forward to provide an additional storage area. To fold the rear seatback, pull on the loops located on the upper seatback. NOTE: These loops can be tucked away when not in use.
Page 176: Driver Memory Seat - If Equipped
174 UNDERSTANDING THE FEATURES OF YOUR VEHICLE DRIVER MEMORY SEAT — IF EQUIPPED WARNING! This feature allows the driver to store up to two different • Be certain that the seatback is securely locked into memory profiles for easy recall through a memory switch.
Page 177: Programming The Memory Feature
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 175 The memory seat switch is located on the driver’s door Programming The Memory Feature trim panel. The switch consists of three buttons: The (S) To create a new memory profile, perform the following: button, which is used to activate the memory save 1.
Page 178: Linking And Unlinking The Remote Keyless Entry Transmitter To Memory
176 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: To program your RKE transmitters, perform the following: • Memory profiles can be set without the vehicle in 1. Remove the Key Fob from the ignition (or change the PARK, but the vehicle must be in PARK to recall a ignition to OFF, for vehicles equipped with Keyless memory profile.
Page 179: Memory Position Recall
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 177 NOTE: Your RKE transmitters can be unlinked to your To recall the memory setting for driver two, press memory settings by pressing the SET (S) button followed MEMORY button number (2) on the driver’s door or the by the UNLOCK button on the RKE transmitter in Step 4 UNLOCK button on the RKE transmitter linked to above.
Page 180 178 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The distance the driver seat moves depends on where driver seat position is between 0.9 in and 2.7 in you have the driver seat positioned when you remove the (22.7 mm and 67.7 mm) forward of the rear stop. Key Fob from the ignition (or change the ignition to OFF, The seat will return to its previously set position when for vehicles equipped with Keyless Enter-N-Go).
Page 181: To Open And Close The Hood
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 179 TO OPEN AND CLOSE THE HOOD 2. Move to the outside of the vehicle and push the safety Two latches must be released to open the hood. catch to the left. The safety catch is located under the center front edge of the hood.
Page 182: Lights
180 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Use the hood prop rod (if equipped) to secure the hood in LIGHTS the open position. Headlight Switch The headlight switch is located on the left side of CAUTION! the instrument panel. This switch controls the operation of the headlights, parking lights, instru- To prevent possible damage, do not slam the hood to ment panel lights, instrument panel light dimming, inte-...
Page 183: Automatic Headlights - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 181 Automatic Headlights — If Equipped This system automatically turns the headlights on or off according to ambient light levels. To turn the system on, rotate the headlight switch counterclockwise to the AUTO position. When the system is on, the headlight time delay feature is also on.
Page 184: Headlights On With Wipers (Available With Automatic Headlights Only)
182 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Headlights On With Wipers (Available With To activate the delay feature, place the ignition in the OFF Automatic Headlights Only) position while the headlights are still on. Then, turn off When this feature is active, the headlights will turn on the headlights within 45 seconds.
Page 185: Smartbeam™ - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 183 SmartBeam™ — If Equipped Adaptive Bi-Xenon High Intensity Discharge The SmartBeam™ system provides increased forward Headlights — If Equipped lighting at night by automating high beam control This system automatically swivels the headlight beam through the use of a digital camera mounted on the pattern horizontally to provide increased illumination in inside rearview mirror.
Page 186: Daytime Running Lights (Drl)
184 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Daytime Running Lights (DRL) Fog Lights — If Equipped The LED Daytime Running Lights will come on when- The front fog light switch is built into the headlight ever the ignition is placed in the RUN position, the switch.
Page 187: Multifunction Lever
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 185 To activate the front fog lights, turn on the parking Multifunction Lever lights or the low beam headlights and press the The multifunction lever controls the operation of the turn headlight switch. To turn off the front fog lights, signals, headlight beam selection and passing lights.
Page 188: Turn Signals
186 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Turn Signals Lane Change Assist Move the multifunction lever up or down and the arrows Tap the lever up or down once, without moving beyond on each side of the instrument cluster flash to show the detent, and the turn signal (right or left) will flash proper operation of the front and rear turn signal lights.
Page 189: Front Map/Reading Lights
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 187 Front Map/Reading Lights Each light can be turned on by pressing a switch on either side of the console. These buttons are backlit for night The front map/reading lights are mounted in the over- time visibility.
Page 190: Courtesy Lights
188 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Courtesy Lights Ambient Light The overhead console is equipped with an ambient light The courtesy lights can be turned on by pressing the top feature. This light casts illumination for improved visibil- corner of the lens. To turn the lights off, press the lens a ity of the floor center console and PRNDL area.
Page 191: Interior Lights
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 189 Interior Lights Dimmer Control The interior lights come on when a door is opened. The dimmer control is part of the headlight switch and is located on the left side of the instrument panel. To protect the battery, the interior lights will turn off automatically 10 minutes after the ignition switch is moved to the LOCK position.
Page 192 190 UNDERSTANDING THE FEATURES OF YOUR VEHICLE With the parking lights or headlights on, rotate the left Ambient Light Control dimmer control upward or downward to increase or Rotate the right dimmer control upward or downward to decrease the brightness of the instrument panel lights increase or decrease the brightness of the door handle and cupholder rings (if equipped).
Page 193: Windshield Wipers And Washers
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 191 Dome Light Position WINDSHIELD WIPERS AND WASHERS Rotate the dimmer control completely upward to the The multifunction lever operates the windshield wipers second detent to turn on the interior lights. The interior and washer when the ignition is placed in the RUN lights will remain on when the dimmer control is in this position.
Page 194: Intermittent Wiper System
192 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Intermittent Wiper System CAUTION! Use the intermittent wiper when weather conditions • Turn the windshield wipers off when driving make a single wiping cycle with a variable pause be- tween cycles desirable. Rotate the end of the multifunc- through an automatic car wash.
Page 195: Mist Feature
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 193 Mist Feature If you activate the washer while the windshield wiper is Rotate the end of the lever downward to the Mist turned off, the wipers will operate for three wipe cycles position to activate a single wipe cycle to clear off road and then turn off.
Page 196 194 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The Headlights On with Wipers feature can be turned on automatically change between an intermittent wipe, slow and off using the Uconnect Touch™ System, refer to wipe and a fast wipe depending on the amount of “Uconnect Touch™...
Page 197 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 195 The Rain Sensing system has protective features for the TILT/TELESCOPING STEERING COLUMN wiper blades and arms. It will not operate under the This feature allows you to tilt the steering column following conditions: upward or downward.
Page 198 196 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To unlock the steering column, pull the control handle POWER TILT/TELESCOPING STEERING COLUMN down. To tilt the steering column, move the steering — IF EQUIPPED wheel upward or downward as desired. To lengthen or This feature allows you to tilt the steering column upward or downward.
Page 199 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 197 To tilt the steering column, move the switch up or down WARNING! as desired. To lengthen or shorten the steering column, pull the switch toward you or push the switch away from Do not adjust the steering column while driving. you as desired.
Page 200 198 UNDERSTANDING THE FEATURES OF YOUR VEHICLE HEATED STEERING WHEEL — IF EQUIPPED Touch the “Controls” soft-key then touch the “Heated The steering wheel contains a heating element that helps Steering Wheel” soft-key to turn on the heated steering warm your hands in cold weather. The heated steering wheel.
Page 201 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 199 Vehicles Equipped With Remote Start On models that are equipped with remote start, the heated steering wheel can be programmed to come on during a remote start. Refer to “Remote Starting System — If Equipped”...
Page 202 200 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The switch is located on the front side of the driver’s seat WARNING! (Continued) cushion side shield. • Do not place anything on the steering wheel that insulates against heat, such as a blanket or steering wheel covers of any type and material..
Page 203 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 201 Press the switch rearward to move the pedals rearward CAUTION! (toward the driver). Do not place any article under the adjustable pedals • The pedals can be adjusted with the ignition OFF. or impede its ability to move as it may cause damage •...
Page 204 202 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ELECTRONIC SPEED CONTROL — IF EQUIPPED When engaged, the Electronic Speed Control takes over accelerator operations at speeds greater than 25 mph (40 km/h). The Electronic Speed Control buttons are located on the right side of the steering wheel.
Page 205 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 203 System can be reactivated by pushing the Electronic To Set A Desired Speed Speed Control ON/OFF button and resetting the desired Turn the Electronic Speed Control ON. When the vehicle vehicle set speed. has reached the desired speed, press the SET (-) button and release.
Page 206 204 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Resume Speed To decrease speed while the Electronic Speed Control is To resume a previously set speed, push the RES (+) set, push the SET (-) button. If the button is continually button and release.
Page 207 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 205 Using Electronic Speed Control On Hills ADAPTIVE CRUISE CONTROL (ACC) — IF The transmission may downshift on hills to maintain the EQUIPPED vehicle set speed. Adaptive Cruise Control (ACC) increases the driving convenience provided by cruise control while traveling NOTE: The Electronic Speed Control system maintains on highways and major roadways.
Page 208 206 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! WARNING! (Continued) • The ACC system: • Adaptive Cruise Control (ACC) is a convenience − Does not react to pedestrians, oncoming vehicles, system. It is not a substitute for active driving and stationary objects (e.g., a stopped vehicle in a involvement.
Page 209 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 207 The Cruise Control system has two control modes: WARNING! • Adaptive Cruise Control mode for maintaining an You should switch off the ACC system: appropriate distance between vehicles. • When driving in fog, heavy rain, heavy snow, •...
Page 210 208 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Adaptive Cruise Control (ACC) Operation NOTE: Any chassis/suspension modifications to the The speed control buttons (located on the right side of the vehicle will effect the performance of the Adaptive Cruise steering wheel) operates the ACC system. Control.
Page 211 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 209 NOTE: You cannot enable ACC under the following To Activate conditions: Push and release the ON/OFF button. The ACC menu in the EVIC displays “Adaptive Cruise Ready.” • When you apply the brakes. •...
Page 212 210 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To turn the system OFF, push and release the ON/OFF WARNING! button again. At this time, the system will turn off and the EVIC will display “Adaptive Cruise Control Off.” Leaving the Adaptive Cruise Control (ACC) system on when not in use is dangerous.
Page 213 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 211 • The system will not be controlling the distance be- tween your vehicle and the vehicle ahead. The vehicle speed will only be determined by the position of the accelerator pedal. ACC Set Remove your foot from the accelerator pedal.
Page 214 212 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Cancel The system will disable ACC without erasing the memory if: • You softly tap the brake pedal. • You depress the brake pedal. • You press the CANCEL switch. • An Anti-Lock Brake System (ABS) event occurs. •...
Page 215 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 213 To Resume Speed To Vary The Speed Setting Press the RES + button and release. Then remove your While ACC is set, you can increase the set speed by foot from the accelerator pedal. The EVIC will display the pressing and holding the RES + button.
Page 216 214 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Pressing the SET - button once will result in a 1 mph Setting The Following Distance In ACC (1.6 km/h) decrease in set speed. Each subsequent tap of The specified following distance for ACC can be set by the button results in a decrease of 1 mph (1.6 km/h).
Page 217 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 215 Distance Set 2 (medium) Distance Set 1 (short) To change the distance setting, press the Distance button and release. Each time the button is pressed, the distance setting adjusts between 3 (long), 2 (medium), and 1 (short).
Page 218 216 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If there is no vehicle ahead, the vehicle will maintain the set The maximum braking applied by ACC is limited; how- speed. If a slower moving vehicle is detected in the same ever, the driver can always apply the brakes manually, if lane, the EVIC displays the “Sensed Vehicle Indicator”...
Page 219 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 217 Brake Alert 3 Brake Alert 2...
Page 220 218 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Adaptive Cruise Control (ACC) Menu The EVIC displays the current ACC system settings. The EVIC is located in the upper part of the instrument cluster between the speedometer and the tachometer. The information it displays depends on ACC system status. Press and release the UP or DOWN button until “ACC”...
Page 221 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 219 • ACC Proximity Warning ACC SET • ACC Unavailable Warning − When ACC is set, the set speed will display. The set speed will continue to display in place of the The EVIC will return to the last display selected odometer reading when changing the EVIC display after five seconds of no ACC display activity.
Page 222 220 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The “Clean Radar Sensor In Front Of Vehicle” message To keep the ACC System operating properly, it is impor- can sometimes be displayed while driving in highly tant to note the following maintenance items: reflective areas (i.e.
Page 223 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 221 When the condition that deactivated the system is no longer present, the system will return to the “Adaptive Cruise Control Off” state and will resume function by simply reactivating it. NOTE: Installing a vehicle front-end protector or an aftermarket grille or modifying the grille is not recom- mended.
Page 224 222 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Service ACC Warning Offset Driving If the system turns off, and the EVIC displays “ACC/ ACC may not detect a vehicle in the same lane that is FCW Unavailable Service Radar Sensor”, it indicates offset from your direct line of travel.
Page 225 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 223 Turns And Bends ACC may occasionally provide braking and/or a driver In turns or bends, ACC may detect a vehicle ahead too alert that you consider unnecessary. This may be the late or too early. This may cause your vehicle to brake late system’s response to signs, guardrails, and other station- or unexpectedly.
Page 226 224 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Using ACC On Hills Lane Changing When driving on hills, ACC may not detect a vehicle in ACC will not detect a vehicle until it is completely in the your lane. Depending on the speed, vehicle load, traffic lane in which you are traveling.
Page 227 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 225 Narrow Vehicles Some narrow vehicles traveling near the outer edges of the lane or edging into the lane are not detected until they have moved fully into the lane. There will not be suffi- cient distance to the vehicle ahead.
Page 228 226 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Stationary Objects And Vehicles General Information ACC does not react to stationary objects and stationary FCC Requirements For Vehicular Radar Systems vehicles. For example, ACC will not react in situations Classification Specifications: where the vehicle you are following exits your lane and 47 C.F.R.
Page 229 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 227 To change modes, press the MODE button when the To Set A Desired Speed system is in either the OFF, READY, or SET position. When the vehicle reaches the speed desired, press the “Cruise Ready”...
Page 230 228 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Cancel If the Cruise Control system is turned off and reactivated, The system will disable normal Cruise Control without the system will return to the last driver setting (ACC or erasing the memory if: Normal Cruise Control).
Page 231 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 229 NOTE: The minimum speed for FCW activation is The default status of FCW is the “Far” setting, this allows 10 mph (16 km/h). the system to warn you of a possible collision with the vehicle in front of you when you are farther away.
Page 232 230 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • FCW will not react to irrelevant objects such as over- head objects, ground reflections, objects not in the path of the car, stationary objects that are far away, oncom- ing traffic, or leading vehicles with the same or higher rate of speed.
Page 233 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 231 Service FCW Warning ParkSense will retain the last system state (enabled or If the system turns off, and the EVIC displays “ACC/ disabled) from the last ignition cycle when the ignition is FCW Unavailable Service Radar Sensor”, it indicates changed to the ON/RUN position.
Page 234 232 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ParkSense Sensors ParkSense Warning Display The four ParkSense sensors, located in the rear fascia/ The ParkSense Warning screen will only be displayed if bumper, monitor the area behind the vehicle that is Sound and Display is selected from the Uconnect within the sensors’...
Page 235 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 233 ParkSense Display The warning display will turn ON indicating the system status when the vehicle is in REVERSE or when the vehicle is in DRIVE and an obstacle has been detected. Park Assist Display Park Assist System ON...
Page 236 234 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The system will indicate a detected obstacle by showing three solid arcs and will produce a one-half second tone. As the vehicle moves closer to the object the EVIC display will show fewer arcs and the sound tone will change from slow, to fast, to continuous.
Page 237 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 235 Fast Tone Continuous Tone...
Page 238 236 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The vehicle is close to the obstacle when the EVIC display shows one flashing arc and sounds a continuous tone. The following chart shows the warning alert operation when the system is detecting an obstacle: WARNING ALERTS Rear Distance Greater than...
Page 239 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 237 Front Park Assist Audible Alerts ASSIST SYSTEM OFF” message for approximately five seconds in REVERSE or for 5 seconds when the vehicle is ParkSense will turn off the Front Park Assist audible in DRIVE. alert (chime) after approximately 3 seconds when an obstacle has been detected, the vehicle is stationary, and Service The ParkSense Park Assist System...
Page 240 238 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Information Center (EVIC)” in “Understanding Your ParkSense System Usage Precautions Instrument Panel” for further information. NOTE: If “CLEAN PARK ASSIST” appears in the Electronic • Ensure that the front and rear bumper are free of snow, Vehicle Information Center (EVIC) make sure the outer ice, mud, dirt and debris to keep the ParkSense surface and the underside of the rear fascia/bumper...
Page 241 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 239 • Clean the ParkSense sensors regularly, taking care CAUTION! not to scratch or damage them. The sensors must not • ParkSense is only a parking aid and it is unable be covered with ice, snow, slush, mud, dirt or debris. Failure to do so can result in the system not working to recognize every obstacle, including small ob- properly.
Page 242 240 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! WARNING! (Continued) • Before using the ParkSense Park Assist System, it • Drivers must be careful when backing up even is strongly recommended that the ball mount and when using the ParkSense Park Assist System. hitch ball assembly is disconnected from the ve- Always check carefully behind your vehicle, look hicle when the vehicle is not used for towing.
Page 243 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 241 PARKVIEW REAR BACK UP CAMERA — IF When the vehicle is shifted out of REVERSE, the rear EQUIPPED camera mode is exited and the navigation or audio screen Your vehicle may be equipped with the ParkView Rear appears again.
Page 244 242 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! CAUTION! • To avoid vehicle damage, ParkView should only Drivers must be careful when backing up even when using the ParkView Rear Back Up Camera. Always be used as a parking aid. The ParkView camera is check carefully behind your vehicle, and be sure to unable to view every obstacle or object in your check for pedestrians, animals, other vehicles, ob-...
Page 245 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 243 Turning ParkView On Or Off — With Touch OVERHEAD CONSOLE Screen Radio The overhead console contains courtesy/reading lights and storage for sunglasses. Universal Garage Door 1. Turn the Radio on. Opener (HomeLink ) and power sunroof switches may 2.
Page 246 244 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Front Map/Reading Lights To turn the lights off, press the switch a second time. The Lights are mounted in the overhead console. Each light lights also turn on when a door is opened. The lights will can be turned on by pressing the switch on either side of also turn on when the UNLOCK button on the RKE is the console.
Page 247 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 245 Sunglass Bin Door GARAGE DOOR OPENER — IF EQUIPPED At the front of the console a compartment is provided for HomeLink replaces up to three hand-held transmitters the storage of a pair of sunglasses. The storage compart- that operate devices such as garage door openers, motor- ment access is a “push/push”...
Page 248 246 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The HomeLink buttons, located on either the overhead console, headliner or sunvisor, designate the three differ- ent HomeLink channels. The HomeLink indicator is located above the center button. HomeLink Buttons/Sunvisor/Headliner NOTE: HomeLink is disabled when the Vehicle Secu- rity Alarm is active.
Page 249 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 247 Before You Begin Programming HomeLink NOTE: • Erasing all channels should only be performed when Be sure that your vehicle is parked outside of the garage before you begin programming. programming HomeLink for the first time. Do not erase channels when programming additional buttons.
Page 250 248 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Programming A Rolling Code For programming garage door openers that were manu- factured after 1995. These garage door openers can be identified by the “LEARN” or “TRAIN” button located where the hanging antenna is attached to the garage door opener.
Page 251 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 249 1. Turn the ignition switch to the ON/RUN position. press and release the “LEARN” or “TRAINING” button. On some garage door openers/devices there may be a 2. Place the hand-held transmitter 1 to 3 in (3 to 8 cm) light that blinks when the garage door opener/device is away from the HomeLink button you wish to program in the LEARN/TRAIN mode.
Page 252 250 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Reprogramming A Single HomeLink Button 3. Simultaneously press and hold both the Homelink To reprogram a channel that has been previously trained, button you want to program and the hand-held transmitter follow these steps: button.
Page 253 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 251 Reprogramming A Single HomeLink Button to pick up the signal during programming. Similar to this To reprogram a channel that has been previously trained, Canadian law, some U.S. gate operators are designed to follow these steps: time-out in the same manner.
Page 254 252 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4. Watch for the HomeLink indicator to change flash Reprogramming A Single HomeLink Button rates. When it changes, it is programmed. It may take up To reprogram a channel that has been previously trained, to 30 seconds or longer in rare cases.
Page 255 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 253 Using HomeLink Troubleshooting Tips To operate, press and release the programmed If you are having trouble programming HomeLink , here HomeLink button. Activation will now occur for the are some of the most common solutions: programmed device (i.e., garage door opener, gate opera- •...
Page 256 254 UNDERSTANDING THE FEATURES OF YOUR VEHICLE General Information WARNING! This device complies with FCC rules Part 15 and Industry • Your motorized door or gate will open and close Canada RSS-210. Operation is subject to the following two conditions: while you are programming the universal trans- ceiver.
Page 257 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 255 POWER SUNROOF — IF EQUIPPED WARNING! The power sunroof switch is located between the sun • Never leave children in a vehicle with the key in visors on the overhead console. the ignition switch. Occupants, particularly unat- tended children, can become entrapped by the power sunroof while operating the power sunroof switch.
Page 258 256 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Opening Sunroof — Express position. The sunroof will close fully and stop automati- Press the switch rearward and release it within one-half cally. This is called “Express Close”. During Express second and the sunroof will open automatically from any Close operation, any movement of the switch will stop position.
Page 259 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 257 NOTE: If three consecutive sunroof close attempts re- Wind Buffeting sult in Pinch Protect reversals, the fourth close attempt Wind buffeting can be described as the perception of will be a Manual Close movement with Pinch Protect pressure on the ears or a helicopter-type sound in the disabled.
Page 260 258 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Ignition OFF Operation COMMANDVIEW SUNROOF WITH POWER SHADE — IF EQUIPPED For vehicles not equipped with the Electronic Vehicle The CommandView sunroof switch is located to the left Information Center (EVIC), the power sunroof switch between the sun visors on the overhead console.
Page 261 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 259 Opening Sunroof — Express WARNING! Press the switch rearward and release it within one-half • Never leave children in a vehicle with the key in second and the sunroof will open automatically from any position.
Page 262 260 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Closing Sunroof — Express automatically. This is called “Express Open”. During Press the switch forward and release it within one-half Express Open operation, any movement of the shade second and the sunroof will close automatically from any switch will stop the shade.
Page 263 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 261 Closing Power Shade — Manual Mode Wind Buffeting To close the shade, press and hold the switch in the Wind buffeting can be described as the perception of forward position. Any release of the switch will stop the pressure on the ears or a helicopter-type sound in the movement and the shade will remain in a partially closed ears.
Page 264 262 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Ignition Off Operation ELECTRICAL POWER OUTLETS For vehicles not equipped with the Electronic Vehicle There are three 12 Volt (13 Amp) electrical power outlets Information Center (EVIC), the power sunroof switch on this vehicle. The power outlets are protected by a fuse. will remain active for 45 seconds after the ignition switch Insert cigar lighter or accessory plug into the power is turned to the LOCK position.
Page 265 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 263 CAUTION! (Continued) • Power outlets are designed for accessory plugs only. Do not insert any other object in the power outlets as this will damage the outlet and blow the fuse. Improper use of the power outlet can cause damage not covered by your New Vehicle Limited Warranty.
Page 266 264 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The center console outlet is powered directly from the There is also a 12 volt power outlet located on the back of battery (power available at all times). Items plugged into the center console for rear passengers. This power outlet this outlet may discharge the battery and/or prevent the has power available only when the ignition is placed in engine from starting.
Page 267 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 265 WARNING! To avoid serious injury or death: • Only devices designed for use in this type of outlet should be inserted into any 12 Volt outlet. • Do not touch with wet hands. •...
Page 268 266 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! CAUTION! (Continued) • After the use of high power draw accessories or • Many accessories that can be plugged in draw long periods of the vehicle not being started (with power from the vehicle’s battery even when not in accessories still plugged in), the vehicle must be use (i.e., cellular phones, etc.).
Page 269 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 267 CUPHOLDERS Front Seat Cupholders The cupholders are located in the forward edge of the center console. Front Cupholders Retractable Cover...
Page 270 268 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Heated and Cooled Cupholders — If Equipped Press the “Cold” symbol once to turn on the cupholder; Your vehicle may be equipped with heated and cooled press the symbol a second time to turn the cupholder off. cupholders.
Page 271 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 269 Rear Seat Cupholders Lighted Cupholders — If Equipped The rear seat cupholders are located in the center armrest On some vehicles the rear cupholders are equipped with a between the rear seats. The cupholders are positioned light ring that illuminates the cupholders for the rear forward in the armrest and side-by-side to provide conve- passengers.
Page 272 270 UNDERSTANDING THE FEATURES OF YOUR VEHICLE STORAGE Glovebox Storage The glovebox storage compartment is located on the passenger side of the instrument panel. Opened Glovebox Storage Compartment Console Features There is a cubby bin located forward of the shift lever. The cubby bin is covered with a push-push actuated door.
Page 273 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 271 Two separate storage compartments are also located small items like an ipod or phone. Below the upper tray, underneath the center console armrest. the lower storage compartment is made for larger items, like CDs and tissue boxes. In addition, the 12 volt power outlet, USB and Aux jack are located here.
Page 274 272 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Door Storage Rear Seat Armrest Storage — If Equipped The door panels contain storage areas. For rear passengers there is a storage bin located in the armrest. Lift upward on the latch to open the storage compartment.
Page 275 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 273 Cargo Area — Vehicles Equipped with 60/40 WARNING! (Continued) Split-Folding Rear Seat • The cargo area in the rear of the vehicle (with the The 60/40 split-folding rear seat provides cargo-carrying rear seatbacks in the locked-up or folded down versatility.
Page 276 274 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CARGO AREA FEATURES WARNING! Trunk Mat — If Equipped The weight and position of cargo and passengers can A trunk mat covers the bottom of the cargo area. The change the vehicle center of gravity and vehicle han- trunk mat is used to protect the interior of the trunk from dling.
Page 277 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 275 GROCERY BAG HOOKS CAUTION! The rear cargo area is equipped with grocery bag hooks, located on either side of the rear cargo area. Do not exceed the maximum weight limit 50 lbs (22 kg) of the grocery bag hook. Damage may occur to hook and mounting surface.
Page 278 276 UNDERSTANDING THE FEATURES OF YOUR VEHICLE REAR WINDOW FEATURES CAUTION! Rear Window Defroster Failure to follow these cautions can cause damage to The rear window defroster button is located on the the heating elements: climate control. Press this button to turn on the •...
Page 279: Understanding Your Instrument Panel
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS ▫ Oil Change Required ....300 Instrument Panel Features ....279 ▫...
Page 280 278 UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Messages # ......309 Steering Wheel Audio Controls ... . 330 ▫...
Page 281: Instrument Panel Features
UNDERSTANDING YOUR INSTRUMENT PANEL 279 INSTRUMENT PANEL FEATURES 1 — Air Outlet 8 — Uconnect Touch™ System Hard Controls 15 — Dimmer Controls 2 — Instrument Cluster 9 — SD Memory Card Slot 16 — Hood Release 3 — Hazard Switch 10 —...
Page 282: Instrument Cluster
280 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER...
Page 283: Instrument Cluster Descriptions
UNDERSTANDING YOUR INSTRUMENT PANEL 281 INSTRUMENT CLUSTER DESCRIPTIONS If the vehicle electronics sense that the vehicle is driven more than 1 mile (1.6 km) with either turn signal on, a 1. Tachometer continuous chime will sound to alert you to turn the The red segments indicate the maximum permissible signals off.
Page 284 282 UNDERSTANDING YOUR INSTRUMENT PANEL 6. Odometer Display / Electronic Vehicle Information Electronic Vehicle Information Center (EVIC) Display Center (EVIC) Display The Electronic Vehicle Information Center (EVIC) fea- tures a driver-interactive display that is located in the Odometer Display instrument cluster. For further information, refer to The odometer display shows the total distance the ve- “Electronic Vehicle Information Center (EVIC)”.
Page 285 UNDERSTANDING YOUR INSTRUMENT PANEL 283 7. Tire Pressure Monitoring Telltale Light — If one or more of your tires is significantly under-inflated. Equipped Accordingly, when the low tire pressure telltale illumi- Each tire, including the spare (if provided), nates, you should stop and check your tires as soon as should be checked monthly when cold and possible, and inflate them to the proper pressure.
Page 286 284 UNDERSTANDING YOUR INSTRUMENT PANEL Your vehicle has also been equipped with a TPMS CAUTION! malfunction indicator to indicate when the system is not operating properly. The TPMS malfunction indicator is The TPMS has been optimized for the original combined with the low tire pressure telltale. When the equipment tires and wheels.
Page 287 UNDERSTANDING YOUR INSTRUMENT PANEL 285 8. Malfunction Indicator Light (MIL) CAUTION! The Malfunction Indicator Light (MIL) is part of an onboard diagnostic system, called OBD, that Prolonged driving with the MIL on could cause dam- monitors engine and automatic transmission con- age to the engine control system.
Page 288 286 UNDERSTANDING YOUR INSTRUMENT PANEL 9. Speedometer 13. Anti-Lock Brake (ABS) Light Indicates vehicle speed. This light monitors the Anti-Lock Brake System (ABS). The light will turn on when the ignition 10. Fuel Door Reminder switch is turned to the ON/RUN position and The arrow in this symbol is a reminder that the may stay on for as long as four seconds.
Page 289 UNDERSTANDING YOUR INSTRUMENT PANEL 287 14. Sport Mode 15. Vehicle Security Light — If Equipped This light will illuminate when Sport or Track This light will flash at a fast rate for approxi- mode is selected. When Sport mode is selected, mately 15 seconds, when the vehicle security the EVIC will display “Sport Mode Active alarm is arming, and then will flash slowly...
Page 290 288 UNDERSTANDING YOUR INSTRUMENT PANEL If the light remains on when the parking brake has been The light will remain on until the cause is corrected. disengaged, and the fluid level is at the full mark on the NOTE: The light may flash momentarily during sharp master cylinder reservoir, it indicates a possible brake cornering maneuvers, which change fluid level condi- hydraulic system malfunction or that a problem with the...
Page 291 UNDERSTANDING YOUR INSTRUMENT PANEL 289 Vehicles equipped with the Anti-Lock Brake System 18. Electronic Stability Control (ESC) Activation/ (ABS), are also equipped with Electronic Brake Force Malfunction Indicator Light — If Equipped Distribution (EBD). In the event of an EBD failure, the The “ESC Activation/Malfunction Indicator Brake Warning Light will turn on along with the ABS Light”...
Page 292 290 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: 19. Seat Belt Reminder Light • The “ESC Off Indicator Light” and the “ESC When the ignition switch is first turned to ON/ Activation/Malfunction Indicator Light” come on mo- RUN, this light will turn on for four to eight mentarily each time the ignition switch is turned to seconds as a bulb check.
Page 293 UNDERSTANDING YOUR INSTRUMENT PANEL 291 The gauge pointer will likely indicate a higher tempera- WARNING! ture when driving in hot weather, up mountain grades, or when towing a trailer. It should not be allowed to A hot engine cooling system is dangerous. You or exceed the upper limits of the normal operating range.
Page 294: Electronic Vehicle Information Center (Evic)
292 UNDERSTANDING YOUR INSTRUMENT PANEL ELECTRONIC VEHICLE INFORMATION CENTER This system allows the driver to select a variety of useful (EVIC) information by pressing the switches mounted on the The Electronic Vehicle Information Center (EVIC) fea- steering wheel. The EVIC consists of the following: tures a driver-interactive display that is located in the •...
Page 295 UNDERSTANDING YOUR INSTRUMENT PANEL 293 The system allows the driver to select information by UP Button pressing the following buttons mounted on the steering Press and release the UP button to scroll upward wheel: through the main menu and Vehicle Info and Trip Info sub-menus (Fuel Economy, Vehicle Info, Tire PSI, Cruise, Messages) and sub-menus.
Page 296: Electronic Vehicle Information Center (Evic) Displays
294 UNDERSTANDING YOUR INSTRUMENT PANEL BACK Button The main display area will normally display the main Press the BACK button to return to the main menu or the screens of a selected feature of the main menu from an info screen or sub-menu item. menu.
Page 297: Evic White Telltales
UNDERSTANDING YOUR INSTRUMENT PANEL 295 • Unstored Messages The Reconfigurable Telltales section is divided into the This message type is displayed indefinitely or until the white telltales area on the right, amber telltales in the condition that activated the message is cleared. Examples middle, and red telltales on the left.
Page 298: Evic Amber Telltales
296 UNDERSTANDING YOUR INSTRUMENT PANEL • Electronic Speed Control SET EVIC Amber Telltales This telltale will illuminate when the electronic This area will show reconfigurable amber caution tell- speed control is SET. For further information, tales. These telltales include: refer to “Electronic Speed Control” in “Under- •...
Page 299: Evic Red Telltales
UNDERSTANDING YOUR INSTRUMENT PANEL 297 • Windshield Washer Fluid Low Indicator • Trunk Ajar This telltale will turn on to indicate the wind- This light will turn on to indicate that the trunk shield washer fluid is low. lid is ajar. •...
Page 300 298 UNDERSTANDING YOUR INSTRUMENT PANEL idle). If the charging system telltale remains on, it means If the telltale remains lit with the engine running, your that the vehicle is experiencing a problem with the vehicle will usually be drivable. However, see an autho- charging system.
Page 301 UNDERSTANDING YOUR INSTRUMENT PANEL 299 If the telltale turns on while driving, safely pull over and CAUTION! stop the vehicle. If the A/C system is on, turn it off. Also, shift the transmission into NEUTRAL and idle the ve- Continuous driving with the Transmission Tempera- hicle.
Page 302: Oil Change Required
300 UNDERSTANDING YOUR INSTRUMENT PANEL Oil Change Required 2. Fully depress the accelerator pedal, slowly, three times Your vehicle is equipped with an engine oil change within 10 seconds. indicator system. The Oil Change Due message will 3. Without pressing the brake pedal, push the ENGINE display in the EVIC for five seconds after a single chime START/STOP button once to return the ignition to the has sounded at the start of each ignition that an oil...
Page 303 UNDERSTANDING YOUR INSTRUMENT PANEL 301 Press the SELECT button to reset the Average Fuel Economy. Press the BACK button to return to the main menu. Average Fuel Economy / ECO Fuel Saver Mode — If Equipped Shows the average fuel economy since the last reset. When Average Fuel Economy is selected, The word RESET>...
Page 304 302 UNDERSTANDING YOUR INSTRUMENT PANEL There is an ECO icon between the Compass and Outside NOTE: Significant changes in driving style or vehicle Temperature info at the top of the EVIC display. This icon loading will greatly affect the actual drivable distance of will appear whenever the Multi-Displacement System the vehicle, regardless of the DTE displayed value.
Page 305: Cruise Control
UNDERSTANDING YOUR INSTRUMENT PANEL 303 Cruise Control conditions change. If Cruise is active and a warning or Press and release the UP or DOWN button until ACC (if other feature is in the EVIC main display, the Cruise equipped with Adaptive Cruise Control) or Cruise is status will be displayed in place of the EVIC odometer highlighted in the EVIC.
Page 306: Trip Info
304 UNDERSTANDING YOUR INSTRUMENT PANEL Trip Info The Trip Functions mode displays the following information: Press and release the UP or DOWN button until Trip Info Trip A is highlighted in the EVIC. Press and release the SELECT Shows the total distance traveled for Trip A since the last button to display the following three trip features in the reset.
Page 307: Tire Psi
UNDERSTANDING YOUR INSTRUMENT PANEL 305 Tire PSI Press and release the UP or DOWN button until Tire PSI WARNING! is highlighted in the EVIC. Press and release the SELECT button and one of the following will be displayed: Measurement of vehicle statistics with the Perfor- •...
Page 308 306 UNDERSTANDING YOUR INSTRUMENT PANEL The Performance Features include the following: The following describes each feature and its operation: • 0-60 mph (0-100 km/h) 0-60 mph (0-100 km/h) When selected, this screen displays the time it takes for • Braking Distance the vehicle to go from 0 to 60 mph (0 to 100 km/h) within •...
Page 309 UNDERSTANDING YOUR INSTRUMENT PANEL 307 • The distance and speed measurements will continue to Braking Distance When selected, this screen displays the vehicle’s braking display until the conditions are met for another event distance and the speed at which the brake pedal was to be recorded.
Page 310: (Customer Information Features)
308 UNDERSTANDING YOUR INSTRUMENT PANEL Instantaneous G-Force Vehicle Info (Customer Information Features) When selected, this screen displays the current G-Force Press and release the UP or DOWN button until Vehicle (lateral and longitudinal). Info is highlighted in the EVIC. Press and release the SELECT button and Coolant Temp will be displayed.
Page 311: Messages
UNDERSTANDING YOUR INSTRUMENT PANEL 309 Messages # Hard-Keys Select from Main Menu using the UP or DOWN buttons. Hard-Keys are located below the Uconnect Touch™ This feature shows the number of stored warning mes- system in the center of the instrument panel. In addition, sages (in the # place holder).
Page 312: Customer Programmable Features - Uconnect Touch™ System 8.4 Settings
310 UNDERSTANDING YOUR INSTRUMENT PANEL Customer Programmable Features — Uconnect Touch™ System 8.4 Settings Press the More soft-key, then press the Settings soft-key to display the menu setting screen. In this mode the Uconnect Touch™ system allows you to access program- mable features that may be equipped such as Display, Clock, Safety/Assistance, Lights, Doors &...
Page 313 UNDERSTANDING YOUR INSTRUMENT PANEL 311 Once the setting is complete press the Back Arrow setting soft-keys or by selecting any point on the scale soft-key to return to the previous menu or press the X between the + and – soft-keys. Then touch the arrow back soft-key to close out of the settings screen.
Page 314 312 UNDERSTANDING YOUR INSTRUMENT PANEL • Units check-mark appears next to the setting, showing that When in this display, you may select to have the EVIC, setting has been selected. Touch the back arrow soft-key odometer, and navigation system (if equipped) changed to return to the previous menu.
Page 315 UNDERSTANDING YOUR INSTRUMENT PANEL 313 • Set Time Minutes Clock After pressing the Clock soft-key the following settings When in this display, you may adjust the minutes. The will be available. Sync with GPS Time soft-key must be unchecked. To make your selection touch the + or - soft-keys to adjust •...
Page 316 314 UNDERSTANDING YOUR INSTRUMENT PANEL until a check-mark appears next to setting, showing that For further information, refer to “Adaptive Cruise Con- setting has been selected. Touch the back arrow soft-key trol (ACC)” in “Understanding The Features Of Your to return to the previous menu. Vehicle”.
Page 317 UNDERSTANDING YOUR INSTRUMENT PANEL 315 previous position when the transmission is shifted out of NOTE: If your vehicle has experienced any damage in REVERSE. To make your selection, touch the Tilt Mirrors the area where the sensor is located, even if the fascia is not damaged, the sensor may have become misaligned.
Page 318 316 UNDERSTANDING YOUR INSTRUMENT PANEL • Rain Sensing Auto Wipers • Headlight Illumination On Approach When this feature is selected, the system will automati- When this feature is selected, the headlights will activate cally activate the windshield wipers if it senses moisture and remain on for 0, 30, 60, or 90 seconds when the doors on the windshield.
Page 319 UNDERSTANDING YOUR INSTRUMENT PANEL 317 • Auto Dim High Beams “SmartBeam™” — If • Steering Directed Lights Equipped When this feature is selected, the headlights turn relative When this feature is selected, the high beam headlights to a change in direction of the steering wheel. To make will deactivate automatically under certain conditions.
Page 320 318 UNDERSTANDING YOUR INSTRUMENT PANEL • Sound Horn With Lock Doors & Locks After pressing the Doors & Locks soft-key the following When this feature is selected, the horn will sound when settings will be available. the remote start is activated. To make your selection, touch the Sound Horn With Lock soft-key, until a check- •...
Page 321 UNDERSTANDING YOUR INSTRUMENT PANEL 319 • Passive Entry 1st Press Of Key Fob Unlocks is selected, you must press the RKE transmitter UNLOCK button twice to unlock the This feature allows you to lock and unlock the vehicle’s passenger’s doors. When Unlock All Doors On 1st Press door(s) without having to press the Remote Keyless is selected, all of the doors will unlock on the first press Entry (RKE) transmitter lock or unlock buttons.
Page 322 320 UNDERSTANDING YOUR INSTRUMENT PANEL • Auto-On Driver Heated/Ventilated Seat & Steering NOTE: The seat will return to the memorized seat location (if Recall Memory with Remote Key Unlock is set Wheel With Vehicle Start — If Equipped to ON) when the Remote Keyless Entry (RKE) transmitter When this feature is selected the driver’s heated seat and is used to unlock the door.
Page 323 UNDERSTANDING YOUR INSTRUMENT PANEL 321 showing that setting has been selected. Touch the back Delay status touch the + or - soft-key to select your arrow soft-key to return to the previous menu. desired time interval. Touch the back arrow soft-key to return to the previous menu.
Page 324 322 UNDERSTANDING YOUR INSTRUMENT PANEL • Perform Compass Calibration NOTE: Keep magnetic materials away from the top of the instrument panel, such as iPod’s, Mobile Phones, Touch the Calibration soft-key to change this setting. This Laptops and Radar Detectors. This is where the compass compass is self-calibrating, which eliminates the need to module is located, and it can cause interference with the manually reset the compass.
Page 325 UNDERSTANDING YOUR INSTRUMENT PANEL 323 • Equalizer • Music Info Cleanup When in this display you may adjust the Bass, Mid and This feature helps organize music files for optimized Treble settings. Adjust the settings with the + and – music navigation.
Page 326: Srt Performance Features
324 UNDERSTANDING YOUR INSTRUMENT PANEL SIRIUS Setup Touch the Subscription Info soft-key to access the Sub- After pressing the SIRIUS Setup soft-key the following scription Information screen. settings will be available. Write down the SIRIUS ID numbers for your receiver. To •...
Page 327 UNDERSTANDING YOUR INSTRUMENT PANEL 325 The Performance Page include the following: WARNING! • Timers Measurement of vehicle statistics with the Perfor- • Engine Values mance Features is intended for off-highway or off- road use only and should not be done on any public •...
Page 328 326 UNDERSTANDING YOUR INSTRUMENT PANEL • The distance measurement will be aborted if the brake The following describes each feature and its operation: pedal is released before the vehicle comes to a com- Timers plete stop. 0-60 mph (0-100 km/h), 1/8 Mile, 1/4 Mile G-Force When selected, this screen displays the time it takes for When selected, this screen displays all four G-Force...
Page 329 UNDERSTANDING YOUR INSTRUMENT PANEL 327 • Battery Voltage • Oil Pressure Shows the actual battery voltage. Shows the actual oil pressure. • Battery Voltage Gauges 2 When selected, this screen displays the following values: Shows the actual battery voltage. • Coolant Temperature Engine Shows the actual coolant temperature within the range of When selected, this screen displays miles per hour (mph),...
Page 330: Setting The Analog Clock
328 UNDERSTANDING YOUR INSTRUMENT PANEL SETTING THE ANALOG CLOCK iPod /USB/MP3 CONTROL — IF EQUIPPED To set the analog clock at the top center of the instrument This feature allows an iPod or external USB device to be panel, press and hold the button until the setting is plugged into the USB port.
Page 331 UNDERSTANDING YOUR INSTRUMENT PANEL 329 proprietary amplifier and speaker technologies deliver- AUX input; and is activated through the Uconnect ing substantial increases in component and system effi- Touch™ System. Refer to “Surround Sound” under ciency levels. “Uconnect Touch™ Settings” in “Understanding Your Instrument Panel”.
Page 332: Steering Wheel Audio Controls
330 UNDERSTANDING YOUR INSTRUMENT PANEL STEERING WHEEL AUDIO CONTROLS The right-hand control is a rocker-type switch with a The remote sound system controls are located on the rear pushbutton in the center and controls the volume and surface of the steering wheel. Reach behind the wheel to mode of the sound system.
Page 333: Cd Player
UNDERSTANDING YOUR INSTRUMENT PANEL 331 The button located in the center of the left-hand control CD/DVD DISC MAINTENANCE will tune to the next preset station that you have pro- To keep a CD/DVD in good condition, take the following grammed in the radio preset pushbutton. precautions: CD Player 1.
Page 334: Radio Operation And Mobile Phones
332 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: If you experience difficulty in playing a particu- CLIMATE CONTROLS lar disc, it may be damaged (i.e., scratched, reflective The air conditioning and heating system is designed to coating removed, a hair, moisture or dew on the disc) make you comfortable in all types of weather.
Page 335: General Overview
UNDERSTANDING YOUR INSTRUMENT PANEL 333 General Overview Hard-Keys Hard-keys are located on the left and right side of the Uconnect Touch™ 4.3 screen in the center of the instru- ment panel. There are also hard-keys located below the Uconnect Touch™ screen. Automatic Climate Controls —...
Page 336 334 UNDERSTANDING YOUR INSTRUMENT PANEL Soft-Keys Soft-keys are accessible on the Uconnect Touch™ system screen. Uconnect Touch™ System 8.4 Automatic Temperature Controls — Soft-keys Uconnect Touch™ System 4.3 Manual Temperature Controls — Soft-keys (If Equipped)
Page 337 UNDERSTANDING YOUR INSTRUMENT PANEL 335 Button Descriptions (Applies To Both Hard-keys And 3. Blower Control Soft-keys) Blower control is used to regulate the amount of air forced through the climate system. There are seven 1. A/C Button blower speeds available. Adjusting the blower will cause Press and release to change the current Air Conditioning automatic mode to switch to manual operation.
Page 338 336 UNDERSTANDING YOUR INSTRUMENT PANEL Hard-key 4. Front Defrost Button The blower speed increases as you turn the control Press and release to change the current airflow setting to clockwise from the lowest blower setting. The blower Defrost mode. The indicator illuminates when this fea- speed decreases as you turn the knob counter-clockwise.
Page 339 UNDERSTANDING YOUR INSTRUMENT PANEL 337 6. Passenger Temperature Control Up Button CAUTION! Provides the passenger with independent temperature control. Push the button for warmer temperature set- Failure to follow these cautions can cause damage to tings. the heating elements: • Use care when washing the inside of the rear NOTE: Pressing this button while in Sync mode will window.
Page 340 338 UNDERSTANDING YOUR INSTRUMENT PANEL 9. AUTO Operation Button NOTE: In Sync mode, this button will also automati- Automatically controls the interior cabin temperature by cally adjust the passenger temperature setting at the adjusting airflow distribution and amount. Performing same time. this function will cause the ATC to switch between 12.
Page 341 UNDERSTANDING YOUR INSTRUMENT PANEL 339 • Bi-Level Mode • Defrost Mode Air comes from the instrument panel outlets and Air comes from the windshield and side window floor outlets. A slight amount of air is directed demist outlets. Use Defrost mode with maximum through the defrost and side window demister outlets.
Page 342: Climate Control Functions
340 UNDERSTANDING YOUR INSTRUMENT PANEL Climate Control Functions Recirculation When outside air contains smoke, odors, or A/C (Air Conditioning) high humidity, or if rapid cooling is desired, The Air Conditioning (A/C) button allows the operator you may wish to recirculate interior air by to manually activate or deactivate the air conditioning pressing the Recirculation control button.
Page 343: Automatic Temperature Control (Atc)
UNDERSTANDING YOUR INSTRUMENT PANEL 341 Automatic Temperature Control (ATC) 3. When the system is set up for your comfort level, it is not necessary to change the settings. You will experience ATC Hard-keys are located in the center of the instru- the greatest efficiency by simply allowing the system to ment panel.
Page 344: Operating Tips
342 UNDERSTANDING YOUR INSTRUMENT PANEL Manual Operation Operating Tips The system allows for manual selection of blower speed, NOTE: Refer to the chart at the end of this section for air distribution mode, A/C status and recirculation con- suggested control settings for various weather conditions. trol.
Page 345 UNDERSTANDING YOUR INSTRUMENT PANEL 343 Vacation Storage NOTE: • Recirculate without A/C should not be used for long Any time you store your vehicle or keep it out of service (i.e., vacation) for two weeks or more, run the air periods, as fogging may occur.
Page 347: Starting And Operating
STARTING AND OPERATING CONTENTS Starting Procedures ....349 Automatic Transmission ....354 ▫...
Page 348 346 STARTING AND OPERATING ▫ Traction Control System (TCS) ... 377 Driving On Slippery Surfaces ... . . 366 ▫ Acceleration ......366 ▫...
Page 349 STARTING AND OPERATING 347 ▫ Tire Loading And Tire Pressure ..391 ▫ Tire Rotation – All Season Tires ..405 Tires — General Information ... . . 395 Tire Pressure Monitor System (TPMS) .
Page 350 348 STARTING AND OPERATING ▫ Overloading ......424 Adding Fuel ......419 ▫...
Page 351: Starting Procedures
STARTING AND OPERATING 349 STARTING PROCEDURES WARNING! (Continued) Before starting your vehicle, adjust your seat, adjust the • Do not leave the key fob in or near the vehicle, and inside and outside mirrors, fasten your seat belt, and if do not leave Keyless Enter-N-Go in the ACC or present, instruct all other occupants to buckle their seat ON/RUN mode.
Page 352: Keyless Enter-N-Go
350 STARTING AND OPERATING Normal Starting CAUTION! (Continued) Using The ENGINE START/STOP Button • Shift into or out of REVERSE only after the vehicle has come to a complete stop and the engine NOTE: Normal starting of either a cold or a warm is at idle speed.
Page 353 STARTING AND OPERATING 351 3. If the shift lever is not in PARK, the ENGINE START/ ENGINE START/STOP Button Functions – With STOP button must be held for two seconds and vehicle Driver’s Foot OFF The Brake Pedal (In PARK Or speed must be above 5 mph (8 km/h) before the engine NEUTRAL Position) will shut off.
Page 354: Extreme Cold Weather (Below -20°F Or 29°C)
352 STARTING AND OPERATING Extreme Cold Weather (Below –20°F Or 29°C) WARNING! (Continued) To ensure reliable starting at these temperatures, use of • Do not attempt to push or tow your vehicle to get an externally powered electric engine block heater (avail- it started.
Page 355: After Starting
STARTING AND OPERATING 353 Clearing A Flooded Engine (Using ENGINE ENGINE BLOCK HEATER — IF EQUIPPED START/STOP Button) The engine block heater warms the engine, and permits If the engine fails to start after you have followed the quicker starts in cold weather. Connect the cord to a “Normal Starting”...
Page 356: Automatic Transmission
354 STARTING AND OPERATING AUTOMATIC TRANSMISSION NOTE: You must press and hold the brake pedal while shifting out of PARK. CAUTION! WARNING! Damage to the automatic transmission may occur if • It is dangerous to move the shift lever out of PARK the following precautions are not observed: •...
Page 357: Key Ignition Park Interlock
STARTING AND OPERATING 355 the transmission in PARK. This system also locks the shift WARNING! (Continued) lever in PARK whenever the ignition switch is in the OFF • Unintended movement of a vehicle could injure position. those in or near the vehicle. As with all vehicles, Brake/Transmission Shift Interlock System you should never exit a vehicle while the engine is This vehicle is equipped with a Brake Transmission Shift...
Page 358: Gear Ranges
356 STARTING AND OPERATING The electronically-controlled transmission provides a Gear Ranges precise shift schedule. The transmission electronics are DO NOT race the engine when shifting from PARK or self-calibrating; therefore, the first few shifts on a new NEUTRAL into another gear range. vehicle may be somewhat abrupt.
Page 359 STARTING AND OPERATING 357 WARNING! WARNING! (Continued) • It is dangerous to move the shift lever out of PARK • Never use the PARK position as a substitute for or NEUTRAL if the engine speed is higher than the parking brake. Always apply the parking idle speed.
Page 360 358 STARTING AND OPERATING WARNING! (Continued) WARNING! (Continued) • Unintended movement of a vehicle could injure • Never leave children alone in a vehicle, or with those in or near the vehicle. As with all vehicles, access to an unlocked vehicle. Allowing children you should never exit a vehicle while the engine is to be in a vehicle unattended is dangerous for a running.
Page 361 STARTING AND OPERATING 359 • Look at the shift lever position display and verify that CAUTION! it indicates the PARK position. • Before moving the shift lever out of PARK, you • With brake pedal released, verify that the shift lever must turn the ignition switch from the LOCK/OFF will not move out of PARK.
Page 362 360 STARTING AND OPERATING DRIVE WARNING! This range should be used for most city and highway driving. It provides the smoothest upshifts and down- Do not coast in NEUTRAL and never turn off the shifts, and the best fuel economy. The transmission ignition to coast down a hill.
Page 363 STARTING AND OPERATING 361 Transmission Limp Home Mode In the event of a momentary problem, the transmission Transmission function is monitored electronically for can be reset to regain all forward gears by performing the abnormal conditions. If a condition is detected that could following steps: result in transmission damage, Transmission Limp Home 1.
Page 364: Autostick
362 STARTING AND OPERATING NOTE: Even if the transmission can be reset, we recom- AUTOSTICK mend that you visit your authorized dealer at your Steering Wheel Mounted Paddle Shifters Or earliest possible convenience. Your authorized dealer has Console Mounted Shifter diagnostic equipment to determine if the problem could AutoStick is a driver-interactive transmission feature that recur.
Page 365 STARTING AND OPERATING 363 • Transmission shifting will be more noticeable when the current transmission gear is displayed in the Elec- tronic Vehicle Information Center (EVIC) portion of the AutoStick is engaged. To disengage AutoStick mode, hold the shift lever to the right or press and hold the (+) instrument cluster.
Page 366: Sport Mode
364 STARTING AND OPERATING Auto SPORT MODE This vehicle is equipped with an electronic controlled • If AutoStick is engaged while in “Auto” mode, the dampening system. This system reduces body roll and transmission will automatically shift up if maximum pitch in many driving situations including cornering, engine speed is reached.
Page 367 STARTING AND OPERATING 365 • Automatic (Auto) Mode — This is the default position When SPORT mode is enabled, a flag will light up in the when vehicle ignition is first turned on. This mode will instrument cluster. Refer to “Instrument Cluster Descrip- give a sporty, but comfortable ride.
Page 368: Acceleration
366 STARTING AND OPERATING DRIVING ON SLIPPERY SURFACES Traction When driving on wet or slushy roads, it is possible for a Acceleration wedge of water to build up between the tire and road Rapid acceleration on snow covered, wet, or other slip- surface.
Page 369: Driving Through Water
STARTING AND OPERATING 367 DRIVING THROUGH WATER Shallow Standing Water Driving through water more than a few inches/ Although your vehicle is capable of driving through centimeters deep will require extra caution to ensure shallow standing water, consider the following Caution safety and prevent damage to your vehicle.
Page 370 368 STARTING AND OPERATING CAUTION! (Continued) WARNING! • Driving through standing water may cause dam- • Driving through standing water limits your vehi- age to your vehicle’s drivetrain components. Al- cle’s traction capabilities. Do not exceed 5 mph ways inspect your vehicle’s fluids (i.e., engine oil, (8 km/h) when driving through standing water.
Page 371: Power Steering
STARTING AND OPERATING 369 • Upon initial start-up in cold weather, the power steer- POWER STEERING The standard power steering system will give you good ing pump may make noise for a short amount of time. vehicle response and increased ease of maneuverability This is due to the cold, thick fluid in the steering in tight spaces.
Page 372: Power Steering Fluid Check
370 STARTING AND OPERATING Power Steering Fluid Check WARNING! Checking the power steering fluid level at a defined service interval is not required. The fluid should only be Fluid level should be checked on a level surface and checked if a leak is suspected, abnormal noises are with the engine off to prevent injury from moving apparent, and/or the system is not functioning as antici- parts and to ensure accurate fluid level reading.
Page 373: Parking Brake
STARTING AND OPERATING 371 PARKING BRAKE Before leaving the vehicle, make sure that the parking brake is fully applied and place the shift lever in the PARK position. The foot operated parking brake is located below the lower left corner of the instrument panel. To apply the park brake, firmly push the park brake pedal fully.
Page 374 372 STARTING AND OPERATING NOTE: WARNING! • When the parking brake is applied and the transmis- • Never use the PARK position as a substitute for sion is placed in gear, the “Brake Warning Light” will flash. If vehicle speed is detected, a chime will sound the parking brake.
Page 375: Brake System
STARTING AND OPERATING 373 WARNING! (Continued) CAUTION! • Do not leave the key fob in or near the vehicle, and If the “Brake Warning Light” remains on with the do not leave a vehicle equipped with Keyless parking brake released, a brake system malfunction Enter-N-Go in the ACC or ON/RUN mode.
Page 376: Anti-Lock Brake System
374 STARTING AND OPERATING In the event power assist is lost for any reason (for is working properly. This self check occurs each time the example, repeated brake applications with the engine vehicle is started and accelerated past 7 mph (11 km/h). OFF) the brakes will still function.
Page 377 STARTING AND OPERATING 375 WARNING! WARNING! (Continued) • The Anti-Lock Brake System (ABS) cannot prevent • The Anti-Lock Brake System contains sophisticated the natural laws of physics from acting on the electronic equipment that may be susceptible to vehicle, nor can it increase braking or steering interference caused by improperly installed or high efficiency beyond that afforded by the condition of output radio transmitting equipment.
Page 378: Electronic Brake Control System
376 STARTING AND OPERATING Anti-Lock Brake Light If both the “Brake Warning Light” and the “Anti-Lock The “Anti-Lock Brake Light” monitors the anti- Brake Light” remain on, the ABS and EBD systems are lock brake system. The light will come on when not functioning.
Page 379: Anti-Lock Brake System (Abs)
STARTING AND OPERATING 377 Anti-Lock Brake System (ABS) Traction Control System (TCS) This system monitors the amount of wheel spin of each This system aids the driver in maintaining vehicle control driven wheel. If wheel spin is detected, brake pressure is under adverse braking conditions by controlling hydrau- applied to the slipping wheel(s) and engine power is lic brake pressure.
Page 380: Electronic Stability Control (Esc)
378 STARTING AND OPERATING power may also be reduced to assist in counteracting the WARNING! condition of oversteer or understeer and help the vehicle maintain the desired path. The BAS cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the The ESC uses sensors in the vehicle to determine the path traction afforded by prevailing road conditions.
Page 381 STARTING AND OPERATING 379 ESC Operating Modes WARNING! The ESC system has three available operating modes: The Electronic Stability Control (ESC) cannot pre- ESC On vent the natural laws of physics from acting on the This is the normal operating mode for the ESC. When- vehicle, nor can it increase the traction afforded by ever the vehicle is started, the ESC system will be in this prevailing road conditions.
Page 382 380 STARTING AND OPERATING The “ESC Off” switch is located in the switch bank near WARNING! the bottom center of the instrument panel. To enter the “Partial Off” mode, momentarily press the “ESC Off” When in “Partial Off” mode, the TCS portion of ESC, switch and the “ESC Activation/Malfunction Indicator except for the limited wheel slip feature described in Light”...
Page 383 STARTING AND OPERATING 381 release the TRIP ODOMETER button located on the NOTE: When the ESC is switched OFF, a feature of the system remains active. This feature controls wheel spin instrument cluster to clear this message. The “ESC OFF” across an axle quite similarly to a limited slip differential.
Page 384: Hill Start Assist (Hsa)
382 STARTING AND OPERATING • Gear selection matches vehicle uphill direction (i.e., Hill Start Assist (HSA) The HSA system is designed to assist the driver when vehicle facing uphill is in forward gear; vehicle back- starting a vehicle from a stop on a hill. HSA will maintain ing uphill is in REVERSE gear).
Page 385: Ready Alert Braking
STARTING AND OPERATING 383 Ready Alert Braking WARNING! Ready Alert Braking may reduce the time required to • HSA is not a parking brake. Always apply the reach full braking during emergency braking situations. It anticipates when an emergency braking situation may parking brake fully when leaving your vehicle.
Page 386: Esc Activation/Malfunction Indicator Light And Esc Off Indicator Light
384 STARTING AND OPERATING ESC Activation/Malfunction Indicator Light and Malfunction Indicator Light” begins to flash during ac- ESC OFF Indicator Light celeration, ease up on the accelerator and apply as little throttle as possible. Be sure to adapt your speed and The “ESC Activation/Malfunction Indicator driving to the prevailing road conditions.
Page 387: Synchronizing Esc
STARTING AND OPERATING 385 Synchronizing ESC TIRE SAFETY INFORMATION If the power supply is interrupted (battery Tire Markings disconnected discharged), “ESC Activation/Malfunction Indicator Light” may illuminate with the engine running. If this should occur, turn the steering wheel completely to the left and then to the right.
Page 388 386 STARTING AND OPERATING • Temporary spare tires are spares designed for tempo- NOTE: • P (Passenger) - Metric tire sizing is based on U.S. rary emergency use only. Temporary high pressure design standards. P-Metric tires have the letter “P” compact spare tires have the letter “T”...
Page 389 STARTING AND OPERATING 387 Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ..blank..= Passenger car tire based on European design standards LT = Light truck tire based on U.S. design standards T or S = Temporary spare tire 31 = Overall diameter in inches (in) 215 = Section width in millimeters (mm)
Page 390 388 STARTING AND OPERATING EXAMPLE: Service Description: 95 = Load Index — A numerical code associated with the maximum load a tire can carry H = Speed Symbol — A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions —...
Page 391: Tire Identification Number (Tin)
STARTING AND OPERATING 389 Tire Identification Number (TIN) Look for the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If the TIN is not found on The TIN may be found on one or both sides of the tire, the outboard side, then you will find it on the inboard however, the date code may only be on one side.
Page 392: Tire Terminology And Definitions
390 STARTING AND OPERATING Tire Terminology And Definitions Term Definition B-Pillar The vehicle B-Pillar is the structural member of the body located behind the front door. Cold tire inflation pressure is defined as the tire pressure after the Cold Tire Inflation Pressure vehicle has not been driven for at least 3 hours, or driven less than 1 mile (1.6 km) after sitting for a three hour period.
Page 393: Tire Loading And Tire Pressure
STARTING AND OPERATING 391 Tire Loading And Tire Pressure Tire And Loading Information Placard Tire And Loading Information Placard Location NOTE: The proper cold tire inflation pressure is listed on the driver’s side B-Pillar or the rear edge of the driver’s side door.
Page 394 392 STARTING AND OPERATING Loading To determine the maximum loading conditions of your The vehicle maximum load on the tire must not exceed vehicle, locate the statement “The combined weight of the load carrying capacity of the tire on your vehicle. You occupants and cargo should never exceed XXX lbs or will not exceed the tire’s load carrying capacity if you XXX kg”...
Page 395 STARTING AND OPERATING 393 4. The resulting figure equals the available amount of NOTE: • The following table shows examples on how to calcu- cargo and luggage load capacity. For example, if “XXX” amount equals 1,400 lbs (635 kg) and there will be five late total load, cargo/luggage, and towing capacities 150 lb (68 kg) passengers in your vehicle, the amount of of your vehicle with varying seating configurations...
Page 396 394 STARTING AND OPERATING...
Page 397: Tires - General Information
STARTING AND OPERATING 395 TIRES — GENERAL INFORMATION WARNING! Tire Pressure Overloading of your tires is dangerous. Overloading Proper tire inflation pressure is essential to the safe and can cause tire failure, affect vehicle handling, and satisfactory operation of your vehicle. Three primary increase your stopping distance.
Page 398 396 STARTING AND OPERATING Economy WARNING! (Continued) Improper inflation pressures can cause uneven wear • Over-inflated or under-inflated tires can affect patterns to develop across the tire tread. These abnormal vehicle handling and can fail suddenly, resulting wear patterns will reduce tread life resulting in a need for in loss of vehicle control.
Page 399: Tire Inflation Pressures
STARTING AND OPERATING 397 Tire Inflation Pressures CAUTION! The proper cold tire inflation pressure is listed on the driver’s side “B” Pillar or rear edge of the driver’s side After inspecting or adjusting the tire pressure, al- door. ways reinstall the valve stem cap. This will prevent moisture and dirt from entering the valve stem, Some vehicles may have Supplemental Tire Pressure which could damage the valve stem.
Page 400: Tire Pressures For High Speed Operation
398 STARTING AND OPERATING Check tire pressures more often if subject to a wide range Tire Pressures For High Speed Operation of outdoor temperatures, as tire pressures vary with The manufacturer advocates driving at safe speeds temperature changes. within posted speed limits. Where speed limits or condi- tions are such that the vehicle can be driven at high Tire pressures change by approximately 1 psi (7 kPa) per speeds, maintaining correct tire inflation pressure is very...
Page 401: Radial Ply Tires
STARTING AND OPERATING 399 Radial Ply Tires Tire Spinning When stuck in mud, sand, snow, or ice conditions, do not WARNING! spin your vehicle’s wheels faster than 30 mph (48 km/h) or for longer than 30 seconds continuously without Combining radial ply tires with other types of tires stopping when you are stuck.
Page 402: Tread Wear Indicators
400 STARTING AND OPERATING Tread Wear Indicators These indicators are molded into the bottom of the tread Tread wear indicators are in the original equipment tires grooves. They will appear as bands when the tread depth to help you in determining when your tires should be becomes 1/16 in (2 mm).
Page 403: Replacement Tires
STARTING AND OPERATING 401 Keep dismounted tires in a cool, dry place with as little It is recommended to replace the two front tires or two exposure to light as possible. Protect tires from contact rear tires as a pair. Replacing just one tire can seriously with oil, grease, and gasoline.
Page 404 402 STARTING AND OPERATING WARNING! WARNING! (Continued) • Never use a tire with a smaller load index or • Do not use a tire, wheel size or rating other than capacity, other than what was originally equipped that specified for your vehicle. Some combinations on your vehicle.
Page 405: Tire Chains
STARTING AND OPERATING 403 TIRE CHAINS CAUTION! (Continued) If driving conditions require tire chains for your vehicle, • Install chains on the rear wheels as tightly as use only chains that meet SAE type “Class S” specifica- possible and then retighten after driving about tions.
Page 406: Tire Rotation Recommendations
404 STARTING AND OPERATING NOTE: In order to avoid damage to tires, chains, and These effects can be reduced by timely rotation of tires. your vehicle do not drive for a prolonged period on dry The benefits of rotation are especially worthwhile with pavement.
Page 407: Tire Rotation - Standard Tires
STARTING AND OPERATING 405 Tire Rotation – Standard Tires Tire Rotation – All Season Tires The suggested rotation method is the “side-to-side” as The suggested rotation method for vehicles equipped shown in the following diagram. with all season tires is the “forward-cross” as shown in the following diagram.
Page 408: Tire Pressure Monitor System (Tpms)
406 STARTING AND OPERATING TIRE PRESSURE MONITOR SYSTEM (TPMS) The TPMS will warn the driver of a low tire pressure if The Tire Pressure Monitor System (TPMS) will warn the the tire pressure falls below the low-pressure warning driver of a low tire pressure based on the vehicle recom- limit for any reason, including low temperature effects mended cold placard pressure.
Page 409 STARTING AND OPERATING 407 For example, your vehicle may have a recommended CAUTION! cold (parked for more than three hours) placard pressure • The TPMS has been optimized for the original of 30 psi (207 kPa). If the ambient temperature is 68°F (20°C) and the measured tire pressure is 27 psi (186 kPa), equipment tires and wheels.
Page 410: Premium System
408 STARTING AND OPERATING • Seasonal temperature changes will affect tire pressure, NOTE: • The TPMS is not intended to replace normal tire care and the TPMS will monitor the actual tire pressure in and maintenance or to provide warning of a tire failure the tire.
Page 411 STARTING AND OPERATING 409 The TPMS consists of the following components: Tire Pressure Monitoring Low Pressure Warnings The TPM Telltale Light will illuminate in the instru- • Receiver module, ment cluster and a chime will sound when tire • Four TPM sensors, pressure is low in one or more of the four active road tires.
Page 412 410 STARTING AND OPERATING Should this occur, you should stop as soon as possible Service TPMS Warning and inflate the tires with a low pressure condition (those If a system fault is detected, the TPM Telltale Light will flashing in the EVIC graphic) to the vehicle’s recom- flash on and off for 75 seconds and then remain on solid.
Page 413 STARTING AND OPERATING 411 If the ignition switch is cycled, this sequence will repeat, 4. Using tire chains on the vehicle. providing the system fault still exists. If the system fault 5. Using wheels/tires not equipped with TPM sensors. no longer exists, the TPM Telltale Light will no longer flash, and the SERVICE TPM SYSTEM message will no The EVIC will also display a SERVICE TPM SYSTEM longer display, and a pressure value will display in place...
Page 414 412 STARTING AND OPERATING Vehicles With Full Size Spare Vehicles With Compact Spare 1. The matching full size spare wheel and tire assembly 1. The compact spare tire does not have a TPM sensor. has a TPM sensor that can be monitored by the TPMS. Therefore, the TPMS will not monitor the pressure in the compact spare tire.
Page 415: General Information
STARTING AND OPERATING 413 4. For each subsequent ignition switch cycle, a chime will General Information sound, the TPM Telltale Light will flash on and off for This device complies with Part 15 of the FCC rules and 75 seconds and then remain on solid, and the EVIC will RSS 210 of Industry Canada.
Page 416: Fuel Requirements
414 STARTING AND OPERATING FUEL REQUIREMENTS Over 40 auto manufacturers worldwide have issued and endorsed consistent gasoline specifications (the World- 6.4L Engine wide Fuel Charter, WWFC) which define fuel properties The 6.4L engine is designed to meet all necessary to deliver enhanced emissions, performance, emissions regulations and provide excel- and durability for your vehicle.
Page 417: Gasoline/Oxygenate Blends
STARTING AND OPERATING 415 Gasoline/Oxygenate Blends E-85 Usage In Non-Flex Fuel Vehicles Some fuel suppliers blend unleaded gasoline with oxy- Non-FFV vehicles are compatible with gasoline contain- genates such as 10% ethanol, MTBE, and ETBE. Oxygen- ing 10% ethanol (E10). Gasoline with higher ethanol ates are required in some areas of the country during the content may void the vehicle’s warranty.
Page 418: Mmt In Gasoline
416 STARTING AND OPERATING To fix a Non-FFV vehicle inadvertently fueled once with vehicles. The manufacturer recommends that gasoline E-85 perform the following: without MMT be used in your vehicle. The MMT content of gasoline may not be indicated on the gasoline pump, •...
Page 419: Fuel System Cautions
STARTING AND OPERATING 417 Fuel System Cautions CAUTION! (Continued) • The use of fuel additives, which are now being CAUTION! sold as octane enhancers, is not recommended. Follow these guidelines to maintain your vehicle’s Most of these products contain high concentra- performance: tions of methanol.
Page 420: Carbon Monoxide Warnings
418 STARTING AND OPERATING Carbon Monoxide Warnings WARNING! (Continued) • Guard against carbon monoxide with proper WARNING! maintenance. Have the exhaust system inspected Carbon monoxide (CO) in exhaust gases is deadly. every time the vehicle is raised. Have any abnor- Follow the precautions below to prevent carbon mal conditions repaired promptly.
Page 421: Adding Fuel
STARTING AND OPERATING 419 ADDING FUEL 2. Open the fuel filler door. 1. Press the fuel filler door release switch (located in the driver’s door map pocket). Fuel Filler Door 3. There is no fuel filler cap. A flapper door inside the pipe seals the system.
Page 422 420 STARTING AND OPERATING 4. Insert the fuel nozzle fully into the filler pipe – the NOTE: A funnel is provided (located in the trunk in the nozzle opens and holds the flapper door while refueling. spare tire area) to open the flapper door to allow for emergency refueling with a gas can.
Page 423: Emergency Fuel Filler Door Release
STARTING AND OPERATING 421 Emergency Fuel Filler Door Release CAUTION! If you are unable to open the fuel filler door, use the fuel filler door emergency release. To avoid fuel spillage and overfilling, do not “top off” the fuel tank after filling. 1.
Page 424: Vehicle Loading
422 STARTING AND OPERATING 3. Pull the release cable. VEHICLE LOADING The load carrying capacity of your vehicle is shown on the “Vehicle Certification Label.” This information should be used for passenger and luggage loading as indicated. Do not exceed the specified Gross Vehicle Weight Rating (GVWR) or the Gross Axle Weight Rating (GAWR).
Page 425: Gross Vehicle Weight Rating (Gvwr)
STARTING AND OPERATING 423 • Gross Axle Weight Rating (GAWR) front Gross Axle Weight Rating (GAWR) The GAWR is the maximum capacity of the front and rear • Gross Axle Weight Rating (GAWR) rear axles. Distribute the load over the front and rear axles •...
Page 426: Overloading
424 STARTING AND OPERATING Overloading Loading The load carrying components (axle, springs, tires, To load your vehicle properly, first figure out its empty wheels, etc.) of your vehicle will provide satisfactory weight, axle-by-axle and side-by-side. Store heavier items service as long as you do not exceed the GVWR and the down low and be sure you distribute their weight as front and rear GAWR.
Page 427: Trailer Towing
STARTING AND OPERATING 425 TRAILER TOWING CAUTION! Trailer towing with this vehicle is not recommended. Towing this vehicle in violation of the above require- RECREATIONAL TOWING (BEHIND ments can cause severe transmission damage. Such MOTORHOME, ETC.) damage is not covered by the New Vehicle Limited Recreational towing (with all four wheels on the ground, Warranty.
Page 429: What To Do In Emergencies
WHAT TO DO IN EMERGENCIES CONTENTS ▫ Preparations For Jump-Start ... . . 441 Hazard Warning Flashers ....428 ▫...
Page 430: Hazard Warning Flashers
428 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHERS IF YOUR ENGINE OVERHEATS The Hazard Warning flasher switch is located in the center In any of the following situations, you can reduce the of the instrument panel between the center air outlets. potential for overheating by taking the appropriate action.
Page 431: Tirefit Kit
WHAT TO DO IN EMERGENCIES 429 TIREFIT KIT CAUTION! Small punctures up to ⁄ ” (6 mm) in the tire tread can be sealed with TIREFIT. Foreign objects (e.g., screws or Driving with a hot cooling system could damage nails) should not be removed from the tire. TIREFIT can your vehicle.
Page 432: Tirefit Storage
430 WHAT TO DO IN EMERGENCIES TIREFIT Storage TIREFIT Kit Components And Operation The TIREFIT kit is located in the trunk. 1. Sealant Bottle TIREFIT Location 2. Deflation Button 3. Pressure Gauge 4. Power Button...
Page 433 WHAT TO DO IN EMERGENCIES 431 5. Mode Select Knob Selecting Sealant Mode Turn the Mode Select Knob (5) to this 6. Sealant Hose (Clear) position to inject the TIREFIT Sealant 7. Air Pump Hose (Black) and to inflate the tire. Use the Sealant Hose (clear hose) (6) when selecting 8.
Page 434: Tirefit Usage Precautions
432 WHAT TO DO IN EMERGENCIES • For optimum performance, make sure the valve stem TIREFIT Usage Precautions on the wheel is free of debris before connecting the • Replace the TIREFIT Sealant Bottle (1) and Sealant TIREFIT kit. Hose (6) prior to the expiration date (printed on the •...
Page 435 WHAT TO DO IN EMERGENCIES 433 WARNING! WARNING! (Continued) • Keep TIREFIT away from open flames or heat • Do not attempt to seal a tire on the side of the source. vehicle closest to traffic. Pull far enough off the •...
Page 436: Sealing A Tire With Tirefit
434 WHAT TO DO IN EMERGENCIES injecting the sealant into the deflated tire and running the WARNING! (Continued) air pump. Move the vehicle as necessary to place the • TIREFIT Sealant solution contains latex. In case of valve stem in this position before proceeding. an allergic reaction or rash, consult a physician 3.
Page 437 WHAT TO DO IN EMERGENCIES 435 5. Uncoil the Power Plug (8) and insert the plug into the If the sealant (white fluid) does not flow within 0 – vehicle’s 12 Volt power outlet. 10 seconds through the Sealant Hose (6): 1.
Page 438 436 WHAT TO DO IN EMERGENCIES If the sealant (white fluid) does flow through the If the tire does not inflate to at least 26 psi (1.8 Bar) Sealant Hose (6): pressure within 15 minutes: • The tire is too badly damaged. Do not attempt to drive 1.
Page 439 WHAT TO DO IN EMERGENCIES 437 3. Immediately disconnect the Sealant Hose (6) from the (D) Drive Vehicle: valve stem, reinstall the cap on the fitting at the end of the Immediately after injecting sealant and inflating the tire, hose, and place the TIREFIT kit in the vehicle storage drive the vehicle 5 miles (8 km) or 10 minutes to ensure location.
Page 440 438 WHAT TO DO IN EMERGENCIES (E) After Driving: If the tire pressure is 19 psi (1.3 bar) or higher: Pull over to a safe location. Refer to “Whenever You Stop 1. Press the Power Button (4) to turn on TIREFIT and to Use TIREFIT”...
Page 441 WHAT TO DO IN EMERGENCIES 439 5. Replace the Sealant Bottle (1) and Sealant Hose (6) 4. Clean any remaining sealant from the TIREFIT hous- assembly at your authorized dealer as soon as possible. ing. Refer to “(F) Sealant Bottle and Hose Replacement.” 5.
Page 442: Jump-Starting Procedures
440 WHAT TO DO IN EMERGENCIES JUMP-STARTING PROCEDURES CAUTION! If your vehicle has a discharged battery it can be jump- started using a set of jumper cables and a battery in Do not use a portable battery booster pack or any another vehicle or by using a portable battery booster other booster source with a system voltage greater pack.
Page 443: Preparations For Jump-Start
WHAT TO DO IN EMERGENCIES 441 Preparations For Jump-Start Remote Battery Posts The battery is stored under an access cover in the trunk. WARNING! Remote battery posts are located on the right side of the engine compartment for jump-starting. • Take care to avoid the radiator cooling fan when- ever the hood is raised.
Page 444: Jump-Starting Procedure
442 WHAT TO DO IN EMERGENCIES 1. Set the parking brake, shift the automatic transmission Jump-Starting Procedure into PARK and turn the ignition to LOCK. WARNING! 2. Turn off the heater, radio, and all unnecessary electri- cal accessories. Failure to follow this procedure could result in per- sonal injury or property damage due to battery ex- 3.
Page 445 WHAT TO DO IN EMERGENCIES 443 1. Connect the positive (+) end of the jumper cable to the 5. Start the engine in the vehicle that has the booster remote positive (+) post of the discharged vehicle. battery, let the engine idle a few minutes, and then start the engine in the vehicle with the discharged battery.
Page 446: Freeing A Stuck Vehicle
444 WHAT TO DO IN EMERGENCIES If frequent jump-starting is required to start your vehicle FREEING A STUCK VEHICLE you should have the battery and charging system in- If your vehicle becomes stuck in mud, sand, or snow, it spected at your authorized dealer. can often be moved by a rocking motion.
Page 447 WHAT TO DO IN EMERGENCIES 445 NOTE: Turn off the Electronic Stability Program (ESP) WARNING! — if equipped, or Traction Control System (TCS) — if equipped before rocking the vehicle. Refer to “Electronic Fast spinning tires can be dangerous. Forces gener- Brake Control”...
Page 448: Shift Lever Override - 5 Speed Transmission
446 WHAT TO DO IN EMERGENCIES SHIFT LEVER OVERRIDE — 5 SPEED 5. Using a screwdriver or similar tool, press and hold the TRANSMISSION override tab through the access port on the center console. If a malfunction occurs and the shift lever cannot be moved out of the PARK position, you can use the following procedure to temporarily move the shift lever: 1.
Page 449: Towing A Disabled Vehicle
WHAT TO DO IN EMERGENCIES 447 TOWING A DISABLED VEHICLE Towing Condition Wheels OFF the Ground SRT8 MODELS IF Transmission is operable: Flat Tow NONE • Transmission in NEUTRAL • 30 mph (48 km/h)max speed Front • 15 mi (24 km) max distance Wheel Lift Rear Flatbed...
Page 450 448 WHAT TO DO IN EMERGENCIES Flatbed towing is recommended. CAUTION! If the transmission is operable, vehicles this vehicle may • Do not use sling type equipment when towing. be towed (with rear wheels on the ground) under the Damage to the fascia will occur. following conditions: •...
Page 451: Without The Ignition Key Fob
WHAT TO DO IN EMERGENCIES 449 Without The Ignition Key Fob CAUTION! Special care must be taken when the vehicle is towed with the ignition in the OFF position. The only approved Failure to follow these towing methods can cause method of towing without the ignition key fob is with a severe transmission damage.
Page 453: Maintaining Your Vehicle
MAINTAINING YOUR VEHICLE CONTENTS ▫ Engine Air Cleaner Filter ....460 Engine Compartment — 6.4L ... . . 453 ▫...
Page 454 452 MAINTAINING YOUR VEHICLE ▫ Brake System ..... . . 476 Bulb Replacement ..... 497 ▫...
Page 455: Engine Compartment - 6.4L
MAINTAINING YOUR VEHICLE 453 ENGINE COMPARTMENT — 6.4L 1 — Remote Jump Start (Positive Battery Post) 6 — Air Cleaner Filter 2 — Engine Oil Dipstick 7 — Power Steering Fluid Reservoir 3 — Engine Oil Fill 8 — Integrated Power Module (Fuses) 4 —...
Page 456: Onboard Diagnostic System - Obd Ii
454 MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM — OBD II CAUTION! Your vehicle is equipped with a sophisticated onboard • Prolonged driving with the MIL on could cause diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic further damage to the emissions control system.
Page 457 MAINTAINING YOUR VEHICLE 455 For states that require an Inspection and Mainte- 3. As soon as you turn the ignition switch to the ON nance (I/M), this check verifies the “Malfunction position, you will see the MIL symbol come on as part of Indicator Light (MIL)”...
Page 458: Replacement Parts
456 MAINTAINING YOUR VEHICLE vehicle as you normally would in order for your OBD II DEALER SERVICE system to update. A recheck with the above test routine Your authorized dealer has the qualified service person- may then indicate that the system is now ready. nel, special tools, and equipment to perform all service operations in an expert manner.
Page 459: Maintenance Procedures
Immediately have potential malfunctions examined by an authorized Chrysler Group LLC dealership or qualified repair center. (Continued)
Page 460: Engine Oil
458 MAINTAINING YOUR VEHICLE Engine Oil Change Engine Oil The oil change indicator system will remind you that it is Checking Oil Level time to take your vehicle in for scheduled maintenance. To assure proper engine lubrication, the engine oil must Refer to “Maintenance Schedule”...
Page 461 MAINTAINING YOUR VEHICLE 459 Materials Added To Engine Oil CAUTION! Do not add any supplemental materials, other than leak detection dyes, to the engine oil. Engine oil is an engi- Do not use chemical flushes in your engine oil as the neered product and its performance may be impaired by chemicals can damage your engine.
Page 462: Engine Oil Filter
460 MAINTAINING YOUR VEHICLE Engine Oil Filter WARNING! The engine oil filter should be replaced with a new filter at every engine oil change. The air induction system (air cleaner, hoses, etc.) can provide a measure of protection in the case of engine Engine Oil Filter Selection backfire.
Page 463: Maintenance-Free Battery
MAINTAINING YOUR VEHICLE 461 Maintenance-Free Battery Your vehicle is equipped with a maintenance-free battery. You will never have to add water, nor is periodic main- tenance required. NOTE: The battery is stored under an access cover in the trunk. Remote battery terminals are located in the engine compartment for jump starting.
Page 464 462 MAINTAINING YOUR VEHICLE WARNING! CAUTION! • Battery fluid is a corrosive acid solution and can • It is essential when replacing the cables on the burn or even blind you. Do not allow battery fluid battery that the positive cable is attached to the to contact your eyes, skin, or clothing.
Page 465: Air Conditioner Maintenance
MAINTAINING YOUR VEHICLE 463 Air Conditioner Maintenance WARNING! For best possible performance, your air conditioner • Use only refrigerants and compressor lubricants should be checked and serviced by an authorized dealer at the start of each warm season. This service should approved by the manufacturer for your air condi- include cleaning of the condenser fins and a performance tioning system.
Page 466: A/C Air Filter
464 MAINTAINING YOUR VEHICLE Refrigerant Recovery And Recycling 1. Remove the access door in the cowl screen by pressing R-134a Air Conditioning Refrigerant is a hydrofluoro- the retaining clips. carbon (HFC) that is endorsed by the Environmental Protection Agency and is an ozone-saving product. How- ever, the manufacturer recommends that air conditioning service be performed by authorized dealers or other service facilities using recovery and recycling equipment.
Page 467 MAINTAINING YOUR VEHICLE 465 2. Unsnap both ends and lift the filter access cover. 4. Install the new filter with arrows pointing in the direction of airflow, which is toward the rear of the vehicle (text and arrows on the filter will indicate this). Filter Access Cover 3.
Page 468: Body Lubrication
466 MAINTAINING YOUR VEHICLE Body Lubrication Windshield Wiper Blades Locks and all body pivot points, including such items as Clean the rubber edges of the wiper blades and the seat tracks, door hinge pivot points and rollers, liftgate, windshield periodically with a sponge or soft cloth and a tailgate, sliding doors and hood hinges, should be lubri- mild nonabrasive cleaner.
Page 469: Adding Washer Fluid
MAINTAINING YOUR VEHICLE 467 Adding Washer Fluid The fluid reservoir will hold nearly 1 gal (4 L) of washer The windshield washer fluid reservoir is located in the fluid when the message “Low Washer Fluid” appears in front of the engine compartment. Be sure to check the the Electronic Vehicle Information Center (EVIC) (if fluid level at regular intervals.
Page 470: Exhaust System
468 MAINTAINING YOUR VEHICLE Exhaust System WARNING! The best protection against carbon monoxide entry into • Exhaust gases can injure or kill. They contain the vehicle body is a properly maintained engine exhaust system. carbon monoxide (CO), which is colorless and odorless.
Page 471 MAINTAINING YOUR VEHICLE 469 Under normal operating conditions, the catalytic con- CAUTION! verter will not require maintenance. However, it is im- • The catalytic converter requires the use of un- portant to keep the engine properly tuned to assure proper catalyst operation and prevent possible catalyst leaded fuel only.
Page 472: Cooling System
470 MAINTAINING YOUR VEHICLE To minimize the possibility of catalytic converter damage: Cooling System • Do not shut off the engine or interrupt the ignition, WARNING! when the transmission is in gear and the vehicle is in • When working near the radiator cooling fan, dis- motion.
Page 473 MAINTAINING YOUR VEHICLE 471 Coolant Checks With the engine at normal operating temperature (but Check engine coolant (antifreeze) protection every not running), check the cooling system pressure cap for 12 months (before the onset of freezing weather, where proper vacuum sealing by draining a small amount of applicable).
Page 474 472 MAINTAINING YOUR VEHICLE Selection Of Coolant CAUTION! (Continued) Use only the manufacturer’s recommended engine cool- • Do not use water alone or alcohol-based engine ant (antifreeze). Refer to “Fluids, Lubricants, and Genu- coolant (antifreeze) products. Do not use addi- ine Parts”...
Page 475 MAINTAINING YOUR VEHICLE 473 • Mix a minimum solution of 50% HOAT engine coolant Adding Coolant Your vehicle has been built with an improved engine and distilled water. Use higher concentrations (not to coolant (antifreeze) that allows extended maintenance exceed 70%) if temperatures below 34°F ( 37°C) are intervals.
Page 476 474 MAINTAINING YOUR VEHICLE Cooling System Pressure Cap WARNING! (Continued) The cap must be fully tightened to prevent loss of coolant, • Do not use a pressure cap other than the one and to ensure that engine coolant (antifreeze) will return to specified for your vehicle.
Page 477 MAINTAINING YOUR VEHICLE 475 Coolant Level Points To Remember The coolant bottle provides a quick visual method for NOTE: When the vehicle is stopped after a few miles determining that the coolant level is adequate. With the (kilometers) of operation, you may observe vapor coming engine OFF and cold, the level of the engine coolant from the front of the engine compartment.
Page 478: Brake System
476 MAINTAINING YOUR VEHICLE • If frequent engine coolant (antifreeze) additions are Brake System required, or if the level in the coolant recovery bottle In order to assure brake system performance, all brake does not drop when the engine cools, the cooling system components should be inspected periodically.
Page 479 MAINTAINING YOUR VEHICLE 477 Master Cylinder – Brake Fluid Level Check Use only manufacturer’s recommended brake fluid. Re- Check the fluid level in the master cylinder immediately if fer to “Fluids, Lubricants, and Genuine Parts” in “Main- the brake system warning light indicates system failure. taining Your Vehicle”...
Page 480 478 MAINTAINING YOUR VEHICLE WARNING! (Continued) WARNING! (Continued) • To avoid contamination from foreign matter or • Overfilling the brake fluid reservoir can result in moisture, use only new brake fluid or fluid that spilling brake fluid on hot engine parts, causing has been in a tightly closed container.
Page 481: Automatic Transmission
MAINTAINING YOUR VEHICLE 479 Automatic Transmission Special Additives Automatic Transmission Fluid (ATF) is an engineered Selection Of Lubricant product and its performance may be impaired by supple- It is important that the proper lubricant is used in the mental additives. Therefore, do not add any fluid addi- transmission to assure optimum transmission perfor- tives to the transmission.
Page 482 480 MAINTAINING YOUR VEHICLE Fluid Level Check CAUTION! (Continued) Regular automatic transmission fluid level checks are not • The fluid level is preset at the factory and it does required. For this reason, the dipstick is omitted. not require adjustment under normal operating If you notice fluid loss or transmission malfunction, have conditions.
Page 483: Rear Axle
MAINTAINING YOUR VEHICLE 481 Rear Axle Appearance Care And Protection From Corrosion For normal service, periodic fluid level checks are not Protection Of Body And Paint From Corrosion required. When the vehicle is serviced for other reasons Vehicle body care requirements vary according to geo- the exterior surfaces of the axle assembly should be graphic locations and usage.
Page 484 482 MAINTAINING YOUR VEHICLE What Causes Corrosion? Washing Corrosion is the result of deterioration or removal of • Wash your vehicle regularly. Always wash your ve- paint and protective coatings from your vehicle. hicle in the shade using MOPAR Car Wash or a mild The most common causes are: car wash soap, and rinse the panels completely with clear water.
Page 485 MAINTAINING YOUR VEHICLE 483 • If you detect any stone chips or scratches in the paint, CAUTION! touch them up immediately. The cost of such repairs is • Do not use abrasive or strong cleaning materials considered the responsibility of the owner. such as steel wool or scouring powder that will •...
Page 486 484 MAINTAINING YOUR VEHICLE Wheel And Wheel Trim Care NOTE: If your vehicle is equipped with Dark Vapor Chrome wheels DO NOT USE wheel cleaners, abrasives • All wheels and wheel trim, especially aluminum and or polishing compounds. They will permanently damage chrome plated wheels, should be cleaned regularly this finish and void your warranty.
Page 487 MAINTAINING YOUR VEHICLE 485 • For grease stains, apply MOPAR Multi-Purpose Your leather upholstery can be best preserved by regular Cleaner or equivalent high quality cleaner to a clean, cleaning with a damp soft cloth. Small particles of dirt damp cloth and remove the stain. Use a fresh, damp can act as an abrasive and damage the leather upholstery towel to remove soap residue.
Page 488 486 MAINTAINING YOUR VEHICLE Cleaning Headlights quarter window equipped with the radio antenna. Do Your vehicle has plastic headlights that are lighter and not use scrapers or other sharp instrument that may less susceptible to stone breakage than glass headlights. scratch the elements.
Page 489: Fuses
MAINTAINING YOUR VEHICLE 487 Seat Belt Maintenance FUSES Do not bleach, dye, or clean the belts with chemical Integrated Power Module solvents or abrasive cleaners. This will weaken the fabric. The Integrated Power Module is located in the engine Sun damage can also weaken the fabric. compartment.
Page 490 488 MAINTAINING YOUR VEHICLE Cavity Car- Mini- Description CAUTION! tridge Fuse • When installing the integrated power module Fuse cover, it is important to ensure the cover is prop- — — Fuse – Spare erly positioned and fully latched. Failure to do so 40 Amp —...
Page 491 MAINTAINING YOUR VEHICLE 489 Cavity Car- Mini- Description Cavity Car- Mini- Description tridge Fuse tridge Fuse Fuse Fuse — 10 Amp Security 50 Amp — Power Steering #2 — 20 Amp Horns 30 Amp — Wiper Motor Yellow Pink — 10 Amp Air Conditioning Clutch 30 Amp...
Page 492 490 MAINTAINING YOUR VEHICLE Cavity Car- Mini- Description Cavity Car- Mini- Description tridge Fuse tridge Fuse Fuse Fuse — 25 Amp Engine Module — 10 Amp Power Steering Natural Module/AC Clutch Relay — — Fuse – Spare — 10 Amp AWD Module/Front —...
Page 493: Rear Power Distribution Center
MAINTAINING YOUR VEHICLE 491 Rear Power Distribution Center CAUTION! There is also a power distribution center located in the • When installing the power distribution center trunk under the spare tire access panel. This center contains fuses and relays. cover, it is important to ensure the cover is prop- erly positioned and fully latched.
Page 494 492 MAINTAINING YOUR VEHICLE Cavity Car- Mini- Description Cavity Car- Mini- Description tridge Fuse tridge Fuse Fuse Fuse 60 Amp — Front PDC Feed #1 30 Amp — Driver Door Yellow Pink — — Fuse – Spare 30 Amp — Passenger Door Pink 60 Amp...
Page 495 MAINTAINING YOUR VEHICLE 493 Cavity Car- Mini- Description Cavity Car- Mini- Description tridge Fuse tridge Fuse Fuse Fuse — — Fuse — Spare — 15 Amp Ignition Switch/Wireless Blue Module — — Fuse — Spare — 10 Amp Steering Column —...
Page 496 494 MAINTAINING YOUR VEHICLE Cavity Car- Mini- Description Cavity Car- Mini- Description tridge Fuse tridge Fuse Fuse Fuse — 25 Amp Rear Heated Seats/ — 20 Amp Front Heated Seats Natural Steering Wheel Yellow — 10 Amp Park Assist/Blind — 10 Amp Heated Cupholders/ Spot/Camera...
Page 497: Vehicle Storage
MAINTAINING YOUR VEHICLE 495 VEHICLE STORAGE Cavity Car- Mini- Description If you are leaving your vehicle dormant for more than tridge Fuse 21 days, you may want to take these steps to protect your Fuse battery. — — Fuse — Spare •...
Page 498: Replacement Bulbs
496 MAINTAINING YOUR VEHICLE REPLACEMENT BULBS Exterior Bulb Number Low Beam/High Beam (Bi-Halogen Headlamp) ......HIR2LL Interior Bulb Number Low Beam/High Beam (Bi-Xenon Headlamp) .
Page 499: Bulb Replacement
MAINTAINING YOUR VEHICLE 497 Exterior Bulb Number WARNING! Backup Lamp ......W21W A transient high tension occurs at the bulb sockets of Center High Mount Stop Lamp (CHMSL).
Page 500 498 MAINTAINING YOUR VEHICLE Standard Low Beam Headlamp, High Beam Headlamp, Park/Turn Lamp, Inner Park Lamp, and Outer Park Lamp 1. Open the hood. NOTE: Removal of the air cleaner filter housing may be necessary prior to replacing bulbs in the headlamp assembly on the driver side of the vehicle.
Page 501 MAINTAINING YOUR VEHICLE 499 3 — Park/Turn Lamp Bulb 4 — Inner Park Lamp Bulb 5 — Outer Park Lamp Bulb...
Page 502: Rear Backup Lamp And Turn Signal Lamps
500 MAINTAINING YOUR VEHICLE 4. Remove the three wing nuts from the back of the tail CAUTION! lamp assembly. Do not touch the new bulb with your fingers. Oil 5. Pull the tail lamp assembly away from the vehicle contamination will severely shorten bulb life. If the enough to access the electrical connector.
Page 503: License Lamp
MAINTAINING YOUR VEHICLE 501 11. Reinstall the bulb and socket assembly into the tail lamp assembly, and then turn it clockwise. 12. Reinstall the tail lamp assembly, fasteners, electrical connector, and trunk trim. 13. Close the trunk. License Lamp 1. Remove the screws securing the lamp to the rear fascia.
Page 504: Fluid Capacities
502 MAINTAINING YOUR VEHICLE FLUID CAPACITIES U.S. Metric Fuel (Approximate) 19 Gallons 72 Liters Engine Oil with Filter 6.4 Liter Engine (SAE 0W-40, Synthetic API Certified) 7 Quarts 6.6 Liters Cooling System * 6.4 Liter Engine (MOPAR Antifreeze/Coolant 5 Year/100,000 Mile 15.2 Quarts 14.4 Liters Formula or equivalent)
Page 505: Fluids, Lubricants, And Genuine Parts
MAINTAINING YOUR VEHICLE 503 FLUIDS, LUBRICANTS, AND GENUINE PARTS Engine Component Fluid, Lubricant, or Genuine Part Engine Coolant MOPAR Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology) or equivalent. Engine Oil For best performance and maximum protection under all types of operat- ing conditions, the manufacturer only recommends full synthetic engine oils that meet the American Petroleum Institute (API) categories of SM or SM/CF.
Page 506: Chassis
504 MAINTAINING YOUR VEHICLE Chassis Component Fluid, Lubricant, or Genuine Part Automatic Transmission MOPAR ATF+4 Automatic Transmission Fluid or equivalent licensed ATF+4 product. Brake Master Cylinder MOPAR DOT 3 and SAE J1703 should be used or equivalent. If DOT 3 brake fluid is not available, then DOT 4 is acceptable.
Page 507 MAINTENANCE SCHEDULES CONTENTS ▫ Required Maintenance Intervals ..508 Maintenance Schedule ....506...
Page 508 506 MAINTENANCE SCHEDULES MAINTENANCE SCHEDULE On Electronic Vehicle Information Center (EVIC) equipped vehicles, “Oil Change Required” will be dis- The Scheduled Maintenance services listed in this played in the EVIC and a single chime will sound, manual must be done at the times or mileages specified to protect your vehicle warranty and ensure the best indicating that an oil change is necessary.
Page 509 MAINTENANCE SCHEDULES 507 NOTE: than your authorized dealer, the message can be reset by • The oil change indicator message will not monitor the referring to the steps described under “Electronic Vehicle time since the last oil change. Change your vehicle’s Information Center (EVIC)/Oil Change Required”...
Page 510 508 MAINTENANCE SCHEDULES Once a Month At Each Oil Change • Check tire pressure and look for unusual wear or • Change the engine oil filter. damage. • Inspect the brake hoses and lines. • Inspect the battery, and clean and tighten the terminals CAUTION! as required.
Page 511 MAINTENANCE SCHEDULES 509 6,000 Miles (10,000 km) or 12,000 Miles (20,000 km) or 12 Months Maintenance Service 6 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. Schedule ❏ Rotate tires. ❏ Change the engine oil and engine oil ❏...
Page 512: Service Schedule
510 MAINTENANCE SCHEDULES 18,000 Miles (30,000 km) or 24,000 Miles (40,000 km) or 24 Months Maintenance Service 18 Months Maintenance Schedule ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate tires. ❏ Change the engine oil and engine oil ❏...
Page 513 MAINTENANCE SCHEDULES 511 30,000 Miles (50,000 km) or 36,000 Miles (60,000 km) or 36 Months Maintenance Service 30 Months Maintenance Schedule ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate tires. ❏ Change the engine oil and engine oil ❏...
Page 514 512 MAINTENANCE SCHEDULES 42,000 Miles (70,000 km) or 48,000 Miles (80,000 km) or 48 Months Maintenance Service 42 Months Maintenance Schedule ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate tires. ❏ Change the engine oil and engine oil ❏...
Page 515 MAINTENANCE SCHEDULES 513 54,000 Miles (90,000 km) or 60,000 Miles (100,000 km) or 60 Months Maintenance Service 54 Months Maintenance Schedule ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate tires. ❏ Change the engine oil and engine oil ❏...
Page 516 514 MAINTENANCE SCHEDULES 66,000 Miles (110,000 km) or 72,000 Miles (120,000 km) or 72 Months Maintenance Service 66 Months Maintenance Schedule ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate tires. ❏ Change the engine oil and engine oil ❏...
Page 517 MAINTENANCE SCHEDULES 515 78,000 Miles (130,000 km) or 84,000 Miles (140,000 km) or 84 Months Maintenance Service 78 Months Maintenance Schedule ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate tires. ❏ Change the engine oil and engine oil ❏...
Page 518 516 MAINTENANCE SCHEDULES 90,000 Miles (150,000 km) or 96,000 Miles (160,000 km) or 96 Months Maintenance Service 90 Months Maintenance Schedule ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate tires. ❏ Change the engine oil and engine oil ❏...
Page 519 MAINTENANCE SCHEDULES 517 102,000 Miles (170,000 km) or 108,000 Miles (180,000 km) or 108 Months Maintenance Service 102 Months Maintenance Schedule ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate tires. ❏ Change the engine oil and engine oil ❏...
Page 520 518 MAINTENANCE SCHEDULES 114,000 Miles (190,000 km) or 120,000 Miles (200,000 km) or 120 Months Maintenance Service 114 Months Maintenance Schedule ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate tires. ❏ Change the engine oil and engine oil ❏...
Page 521 MAINTENANCE SCHEDULES 519 126,000 Miles (210,000 km) or 132,000 Miles (220,000 km) or 132 Months Maintenance Service 126 Months Maintenance Schedule ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate tires. ❏ Change the engine oil and engine oil ❏...
Page 522 520 MAINTENANCE SCHEDULES 138,000 Miles (230,000 km) or 144,000 Miles (240,000 km) or 144 Months Maintenance Service 138 Months Maintenance Schedule ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate tires. ❏ Change the engine oil and engine oil ❏...
Page 523 MAINTENANCE SCHEDULES 521 150,000 Miles (250,000 km) or WARNING! 150 Months Maintenance Service • You can be badly injured working on or around a Schedule ❏ Change the engine oil and engine oil filter. motor vehicle. Do only service work for which you ❏...
Page 525: If You Need Consumer Assistance
If You Need Assistance ....525 Reporting Safety Defects ....529 ▫ Chrysler Group LLC Customer Center ..526 ▫ In The 50 United States And Washington, D.C.
Page 526 524 IF YOU NEED CONSUMER ASSISTANCE ▫ Traction Grades ..... 532 Publication Order Forms ....530 ▫...
Page 527: Suggestions For Obtaining Service For Your Vehicle
IF YOU NEED CONSUMER ASSISTANCE 525 SUGGESTIONS FOR OBTAINING SERVICE FOR Be Reasonable With Requests YOUR VEHICLE If you list a number of items and you must have your vehicle by the end of the day, discuss the situation with Prepare For The Appointment the service advisor and list the items in order of priority.
Page 528: Chrysler Group Llc Customer Center
• Vehicle delivery date and mileage This is why you should always talk to an authorized dealer’s service manager first. Most matters can be re- Chrysler Group LLC Customer Center solved with this process. P.O. Box 21–8004 Auburn Hills, MI 48321–8004 •...
Page 529: Customer Assistance For The Hearing Or Speech Impaired (Tdd/Tty)
IF YOU NEED CONSUMER ASSISTANCE 527 Customer Assistance For The Hearing Or Speech Service Contract Impaired (TDD/TTY) You may have purchased a service contract for a vehicle To assist customers who have hearing difficulties, the to help protect you from the high cost of unexpected manufacturer has installed special TDD (Telecommuni- repairs after the manufacturer’s New Vehicle Limited cation Devices for the Deaf) equipment at its customer...
Page 530: Warranty Information
See the Warranty Information Booklet, located on the training to assure that you are absolutely delighted with DVD, for the terms and provisions of Chrysler Group the ownership experience. You’ll be pleased with their LLC warranties applicable to this vehicle and market.
Page 531: Mopar Parts
IF YOU NEED CONSUMER ASSISTANCE 529 MOPAR PARTS To contact NHTSA, you may either call the Auto Safety MOPAR fluids, lubricants, parts, and accessories are Hotline toll free at 1–888–327–4236 (TTY: 1–800–424– available from an authorized dealer. They are recom- 9153), or go to http://www.safercar.gov;...
Page 532 Chrysler Group assistance of service and engineering specialists to LLC vehicles. A complete working knowledge of the acquaint you with specific Chrysler Group LLC ve- vehicle, system, and/or components is written in hicles. Included are starting, operating, emergency...
Page 533 IF YOU NEED CONSUMER ASSISTANCE 531 Call toll free at: All passenger car tires must conform to Federal safety requirements in addition to these grades. • 1–800–890–4038 (U.S.) Treadwear • 1–800–387–1143 (Canada) The Treadwear grade is a comparative rating, based on the wear rate of the tire when tested under controlled conditions on a specified government test course.
Page 534 532 IF YOU NEED CONSUMER ASSISTANCE Traction Grades material of the tire to degenerate and reduce tire life, and The Traction grades, from highest to lowest, are AA, A, B, excessive temperature can lead to sudden tire failure. The and C. These grades represent the tire’s ability to stop on grade C corresponds to a level of performance, which all wet pavement, as measured under controlled conditions on passenger car tires must meet under the Federal Motor...
Page 535 INDEX...
Page 536 534 INDEX About Your Brakes ....371,373 Airbag, Side ..... . 60,62,65,66 ABS (Anti-Lock Brake System) .
Page 537 INDEX 535 Automatic Door Locks ..... 31 Battery ....... 461 Automatic Headlights .
Page 538 536 INDEX Bulb Replacement ..... 496,497 Checks, Safety ......83 Bulbs, Light .
Page 539 INDEX 537 Console, Overhead ..... . . 243 Data Recorder, Event ..... . 70 Contract, Service .
Page 540 538 INDEX Door Locks, Automatic ....31 Electronic Vehicle Information Door Opener, Garage ..... 245 Center (EVIC) .
Page 541 INDEX 539 Exhaust Gas Caution ....84,418 Event Data Recorder ..... . 70 Fails to Start .
Page 542 540 INDEX Fluid Capacities ......502 Ethanol ......415 Fluid Leaks .
Page 543 INDEX 541 Gasoline, Clean Air ..... . 414 Hazard Warning Flasher ....428 Gasoline, Reformulated .
Page 544 542 INDEX High Beam/Low Beam Select (Dimmer) Switch . . 186 Interior Lights ......189 Hill Start Assist .
Page 545 INDEX 543 Lap/Shoulder Belts ..... . . 47 Electronic Stability Program (ESP) LATCH (Lower Anchors and Tether Indicator ......384 for CHildren) .
Page 546 544 INDEX Malfunction Indicator (Check Engine) ..285 Loading Vehicle ..... . 422,424 Map Reading ..... 187,188 Capacities .
Page 547 INDEX 545 Malfunction Indicator Light Mode (Check Engine) ..... . . 285,455 Fuel Saver ......301 Manual Transmission .
Page 548 546 INDEX Oil, Engine ......458,503 Overhead Console ..... . . 243 Capacity .
Page 549 INDEX 547 Seats ......162 Rear Seat, Folding ..... . . 173 Steering .
Page 550 548 INDEX Reporting Safety Defects ....529 And Pregnant Women ....56 Resetting Oil Change Indicator .
Page 551 INDEX 549 Tilting ......162 Side View Mirror Adjustment ....97 Security Alarm (Theft Alarm) .
Page 552 550 INDEX Starting and Operating ....349 Supplemental Restraint System - Airbag ..56 Starting Procedures .
Page 553: Vehicle
INDEX 551 Tires ......87,395,531 Towing ....... 425 Aging (Life of Tires) .
Page 554 552 INDEX Tread Wear Indicators ....400 Vehicle Storage ..... . . 343,495 Trip Odometer .
Page 555 INDEX 553 Windows ......38 Windshield Wiper Blades ....466 Power .
Page 556 INSTALLATION OF RADIO TRANSMITTING EQUIPMENT Special design considerations are incorporated into this The antenna cable should be as short as practical and vehicle’s electronic system to provide immunity to radio routed away from the vehicle wiring when possible. Use frequency signals. Mobile two-way radios and telephone only fully shielded coaxial cable.
Page 557 Chrysler Group LLC Printed in U.S.A. 12C482-126-AD 4th Edition...

This manual is also suitable for:

300 srt8 2012

Chrysler SRT8 2012 Owner's Manual

Introduction 1

Things to Know before Starting Your Vehicle

Understanding the Features of Your Vehicle

Understanding Your Instrument Panel

Starting and Operating

What to Do in Emergencies

Maintaining Your Vehicle

If You Need Consumer Assistance

Quick Links

Chapters

Related Manuals for Chrysler SRT8 2012

Summary of Contents for Chrysler SRT8 2012