Assign Setting - Boss GT-1000 Parameter Manual

Value Explanation
Controls the Start/Stop of external MIDI devices (such
MIDI START
as sequencers).
Controls the Play/Stop of external MIDI devices (such as
MMC PLAY
hard disk recorders).
Turns the trigger on/off when the MASTER DELAY's TYPE
MDLY TRIGGER
is WARP or TWIST.
TUNER Switches the TUNER on and off.
MANUAL *2 Switches the MANUAL on and off.
Turns MANUAL on/off when briefly pressed; turns
MANUAL/TUNER *2
TUNER on/off when long-pressed.
*1 Not shown in "CUR NUM" and "MANUAL1–5. "
*2 Not shown if CONTROL MODE (p. 28) is set to PEDALBOARD.
*3 If CONTROL MODE (p. 28) is set to PEDALBOARD, this will be "TUNER. "
FUNCTION (EXP1 PEDAL, EXP 2, EXP 3)
Value Explanation
OFF No assignment.
FOOT VOLUME
Foot volume will be assigned.
PEDAL FX will be assigned.
PEDAL FX
According to the pedal effect setting, this operates as
wah or as pedal bend.
FV/PEDAL FX PEDAL FX and foot volume will be assigned.
Foot volume will be assigned.
FV+TUNER
TUNER is displayed if the pedal is returned all the way.
PEDAL FX and foot volume will be assigned.
FV+TUNER/PFX
TUNER is displayed if the pedal is returned all the way
when using foot volume.
MODE
Value Explanation
The setting is toggled On (maximum value) or Off
TOGGLE
(minimum value) with each press of the footswitch.
The normal state is Off (minimum value), with the
MOMENT switch On (maximum value) only while the footswitch
is depressed.
PREFERENCE
* This cannot be selected if CONTROL MODE (p. 28) is set to
PEDALBOARD.
Value Explanation
Different settings can be made independently for each
PATCH
patch.
SYSTEM The same settings will be shared by all patches.

ASSIGN SETTING

ASSIGN 1–16
For each parameter, you can specify, in detail, which controller will
control which parameter. You can create 16 sets of such assignments.
Parameter Value
SW OFF, ON
This selects the parameter to be changed.
TARGET
Refer to "TARGET list" (p. 31).
This sets the minimum value for the range in which the
MIN
parameter can change. The value differs depending on
TARGET
the parameter assigned for TARGET parameter.
This sets the maximum value for the range in
which the parameter can change. The value differs
MAX
depending on the parameter assigned for TARGET
parameter.
NUM1–NUM5
CUR NUM
BANKDOWN
BANKUP
CTL1–CTL3
CTL4, CTL5
CTL6, CTL7
EXP1 SW
SOURCE
EXP1
EXP2
EXP3
SOURCE
INT PEDAL
WAVE PEDAL
INPUT
CC#1–31, 64–95
MOMENT
MODE
TOGGLE
ACT LOW 0–126
ACT HIGH 1–127
SENS
0–100
MENU
Explanation
Turns the ASSIGN 1–16 on/off.
Assigns the GT-1000's number [1]–[5]
switch.
Assigns the same number switch as
the selected patch number.
Assigns the GT-1000's [BANK I ]
switch.
Assigns the GT-1000's [BANK H ]
switch.
Assigns the GT-1000's [CTL1]–[CTL3]
switch.
Assigns the external footswitch
connected to the CTL 4, 5/ EXP 2
jack.
Assigns the external footswitch
connected to the CTL 6, 7/ EXP 3
jack.
Assigns the GT-1000's [EXP 1] switch.
Assigns the GT-1000's expression
pedal.
Assigns the external expression
pedal connected to the CTL 4, 5/
EXP 2 jack.
Assigns the external expression
pedal connected to the CTL 6, 7/
EXP 3 jack.
Assigns the Refer to"Virtual
internal pedal. Expression Pedal
System (Internal
Assigns the
Pedal / Wave
wave pedal.
Pedal)" (p. 36).
The assigned target parameter will
change according to the input level.
Control Change messages from an
external MIDI device.
The normal state is Off (minimum
value), with the switch On
(maximum value) only while the
footswitch is depressed.
The setting is toggled On (maximum
value) or Off (minimum value) with
each press of the footswitch.
You can set the controllable range
for target parameters within the
source's operational range. Target
parameters are controlled within the
range set with ACT LOW and ACT
HIGH. You should normally set ACT
LOW to 0 and ACT HIGH to 127.
This adjusts the input sensitivity
when INPUT is selected for SOURCE.
29