Pitch Shifter; Ring Mod - Boss GT-1000 Parameter Manual

PITCH SHIFTER

This effect changes the pitch of the original sound (up or down)
within a range of two octaves.
Parameter Value
Selects the number of voices for the pitch shift sound.
1VOICE
VOICE
2MONO
2STEREO
PS1:PITCH
-24–+24
PS2:PITCH
DIRECT LEVEL
0–100
Selection for the pitch shifter mode.
FAST,
MEDIUM,
SLOW
PS1:MODE
PS2:MODE
MONO
PS1:FINE
-50–+50
PS2:FINE
PS1:PRE-DELAY
0ms–300ms,
BPM ` – Œ
PS2:PRE-DELAY
PS1:LEVEL
0–100
PS2:LEVEL
PS1:FEEDBACK
0–100
BPM 40–250
Explanation
One-voice pitch-shifted sound output in
mono.
Two-voice pitch-shifted sound (PS1, PS2)
output in mono.
Two-voice pitch-shifted sound (PS1, PS2)
output through left and right channels.
Adjusts the amount of pitch shift (the
amount of interval) in semitone steps.
Adjusts the volume of the direct sound.
The response is slower in the order
of FAST, MEDIUM and SLOW, but the
modulation is lessened in the same order.
MONO is used for inputting single notes.
* You may be unable to produce
the intended effect when playing
chords (two or more notes played
simultaneously).
Make fine adjustments to the interval. The
amount of the change in the Fine 100 is
equivalent to that of the Pitch 1.
Adjusts the time from when the direct
sound is heard until the pitch shifted
sounds are heard. Normally you can leave
this set at 0 ms.
* When set to BPM, the value of each
parameter will be set according to the
value of the "MASTER BPM" specified
for each patch. This makes it easier
to achieve effect sound settings that
match the tempo of the song.
* If, due to the tempo, the time is longer
than the range of allowable settings, it
is then synchronized to a period either
1/2 or 1/4 of that time.
Adjusts the volume of the pitch shifter.
Adjusts the feedback amount of the pitch
shift sound.
Adjusts the BPM value for each patch.
* BPM (beats per minute) indicates the
number of quarter note beats that
occur each minute
* When you have an external MIDI
device connected, the MASTER BPM
synchronizes to the external MIDI
devices tempo, making it impossible to
set the MASTER BPM. To enable setting
of the MASTER BPM, set "SYNC CLOCK"
(p. 41) to "INTERNAL. "

RING MOD.

This creates a bell-like sound by ring-modulating the guitar sound
with the signal from the internal oscillator.
The sound can be unmusical and lack distinctive pitches.
Parameter Value
INTELLIGENT OFF, ON
FREQUENCY 0–100
0–100,
FREQ MOD RATE
BPM ΠР`
FREQ MOD
0–100
DEPTH
EFFECT LEVEL 0–100
DIRECT MIX 0–100
BPM 40–250
Explanation
If this is ON, the oscillator frequency changes
according to the pitch of the input sound,
producing a pitched sound. In this case, the
expected effect does not occur if the pitch
of the guitar sound is not detected correctly.
We recommend that you use this with single-
note playing.
Adjusts the frequency of the internal
oscillator.
Adjusts the rate at which the internal
oscillator is modulated.
* When set to BPM, the value of each
parameter will be set according to the
value of the "MASTER BPM" specified for
each patch. This makes it easier to achieve
effect sound settings that match the
tempo of the song.
* If, due to the tempo, the time is longer
than the range of allowable settings, it is
then synchronized to a period either 1/2
or 1/4 of that time.
Adjusts the depth to which the internal
oscillator is modulated.
Adjusts the volume of the effect sound.
Adjusts the volume of the direct sound.
Adjusts the BPM value for each patch.
* BPM (beats per minute) indicates the
number of quarter note beats that occur
each minute
* When you have an external MIDI
device connected, the MASTER BPM
synchronizes to the external MIDI devices
tempo, making it impossible to set the
MASTER BPM. To enable setting of the
MASTER BPM, set "SYNC CLOCK" (p. 41) to
"INTERNAL. "
Effect
19