Boss GT-1000 Parameter Manual page 13

Parameter Value
FLAT,
LOW CUT *1
20.0Hz–20.0kHz
20.0Hz–20.0kHz,
HIGH CUT *1
FLAT
DIRECT LEVEL 0–100
BPM 40–250
*1 Not shown if TYPE is set to CE-1 CHORUS or CE-1 VIBRATO.
DUAL
Parameter Value
RATE
0–100,
BPM ΠР`
RATE 2
DEPTH
0–100
DEPTH 2
PRE-DELAY 1
0.0ms–40.0ms
PRE-DELAY 2
EFFECT LEVEL 1
0–100
EFFECT LEVEL 2
TRI
WAVEFORM
WAVEFORM 2
SINE
LOW CUT 1
FLAT,
20.0Hz–20.0kHz
LOW CUT 2
HIGH CUT 1
20.0Hz–20.0kHz,
FLAT
HIGH CUT 2
DIRECT LEVEL 0–100
Explanation
This sets the frequency at which the low
cut filter begins to take effect. When FLAT
is selected, the low cut filter will have no
effect.
This sets the frequency at which the high
cut filter begins to take effect. When FLAT
is selected, the high cut filter will have no
effect.
Adjusts the volume of the direct sound.
Setting this to 0 cuts the direct sound.
Adjusts the BPM value for each patch.
* BPM (beats per minute) indicates the
number of quarter note beats that occur
each minute
* When you have an external MIDI
device connected, the MASTER BPM
synchronizes to the external MIDI
devices tempo, making it impossible to
set the MASTER BPM. To enable setting
of the MASTER BPM, set "SYNC CLOCK"
(p. 41) to "INTERNAL. "
Explanation
Adjusts the rate of the chorus effect.
* When set to BPM, the value of each
parameter will be set according
to the value of the "MASTER BPM"
specified for each patch. This makes
it easier to achieve effect sound
settings that match the tempo of
the song.
* If, due to the tempo, the time is
longer than the range of allowable
settings, it is then synchronized to a
period either 1/2 or 1/4 of that time.
Adjusts the depth of the chorus effect.
* To use it for doubling effect, set the
value to 0.
Adjusts the time needed for the effect
sound to be output after the direct
sound has been output. By setting a
longer pre delay time, you can obtain an
effect that sounds like more than one
sound is being played at the same time
(doubling effect).
Adjusts the volume of the effect sound.
Produces a typical chorus effect.
Produces a deeper sense of modulation.
This sets the frequency at which the low
cut filter begins to take effect. When
FLAT is selected, the low cut filter will
have no effect.
This sets the frequency at which the
high cut filter begins to take effect.
When FLAT is selected, the high cut filter
will have no effect.
Adjusts the volume of the direct sound.
Setting this to 0 cuts the direct sound.
Parameter Value
BPM 40–250
MONO
OUTPUT MODE
STEREO
PRIME
Parameter Value
SWEETNESS 0–100
BELL 0–100
MONO
OUTPUT MODE
STEREO
CE-1 CHORUS, CE-1 VIBRATO
Parameter Value
PREAMP SW OFF, ON
PREAMP GAIN 0–100
PREAMP LEVEL 0–100
Effect
Explanation
Adjusts the BPM value for each patch.
* BPM (beats per minute) indicates the
number of quarter note beats that
occur each minute
* When you have an external MIDI
device connected, the MASTER BPM
synchronizes to the external MIDI
devices tempo, making it impossible
to set the MASTER BPM. To enable
setting of the MASTER BPM, set "SYNC
CLOCK" (p. 41) to "INTERNAL. "
This setting is appropriate for mono
output.
Produces a rich spaciousness when
stereo output is used.
Explanation
Higher values produce a more
enveloping sound.
Higher values produce a more brilliant
sound.
This setting is appropriate for mono
output.
Produces a rich spaciousness when
stereo output is used.
Explanation
Specifies whether the CE-1's preamp is
simulated (ON) or not simulated (OFF).
Adjusts the gain of the preamp. Higher
settings will produce distortion.
Adjusts the volume of the preamp.
13