Table of Contents
Advertisement
265. [Rmirror] In web page, create Rmirror VLAN ruler without reflect port, show running will
display mirror-port "" in Rmirror VLAN ruler.
266. [Rmirror] In web page, it must enable mirror port and direction, then work. But, in cli, it
only configure mirror port direction directly. It make user confuse easily.
267. [MIB-zyxelMvr] The zyMvrGroupRowStatus (OID: 1.3.6.1.4.1.890.1.15.3.55.1.5.1.6) can
be created to over max rules via SNMPc.
268. [IPv6]In web page, create 128 interface VLAN, it can display 128 interface VLAN in IPv6
link-local address setup. But, it only can display 64 interface VLAN in IPv6 global address
setup.
269. [IPv6] In web page, user can modify and delete the global address ruler. But, user only
can modify the link-local address ruler. What is difference between global address and
link-local address.
270. [IPv6 Static Route] Create maximum ipv6 static route, it could not diplay the correct
delete and clear items.
271. [IPv6 Link-Local Address Setup] In IPv6 link-local address setup page, create 2 interface
VLAN ruler, and click interface VLAN 2, the related parameter still keep interface VLAN 1
information.
272. [syslog] when out-band port link up/down, sent event/trap to both syslog and SNMP
should be the same info. (in syslog displays GS3700 interface: port 1link down; in SNMPc:
interface 10000 link down trap)
273. [Rmirror] In DHCP snooping, the received DHCP discovery in connected port should be
double tagged (Rmirror + DHCP DHCP-VLAN), not single tagged.
274. [IPv6] The suggestion value range of minimum Interval in IPv6 Router Discovery Setup
should be 3~1350, not 3~1500 via Web.
275. [IPv6] Set Valid Lifetime value 9999999999 in IPv6 Prefix Setup, then value will change
to 0 via Web.
276. [IPv6 Prefix Setup] In IPv6 prefix setup, create preferred lifetime is bigger than valid
lifetime, web page will pop warning message. "Prefix lifetime must be exceed valid
lifetime". The behavior is abnormal. Besides, the message information seems be wrong.
277. [IPv6 Neighbor Setup] In IPv6 neighbor setup page, create neighbor setup entry without
the related interface VLAN, it could not directly delete the neighbor setup ruler. It will pop
error message. Interface id range error.
278. [IPv6 Interface Setup] In IPv6 interface setup page, create 2 interface ruler, and click
interface VLAN 2, the related parameter still keep the VLAN 1 information.
279. [Rmirror] In bandwidth control, the received rate in connected port should follow egress
setting in egress port, not ingress port setting.
280. [IPv6] In Ipv6 global address, create ipv6 address 5001::1/128 and enable eui-64 in web
page, the ipv6 address in cli and web will be 5000::219:cbff:fe01:101/128. But, show
running will display as ipv6 address ::/128 eui-64.
281. [Private VLAN] In show VLAN counter, sometimes, the received packets is not equal to
the SMB send packets.
282. [MLD Filtering Profile] Create maximum MLD filtering profile, it will have 2 delete items on
web page.
283. [Web] Set ipv6 link-local address and default gateway via Web, the DUT hang up.
284. [Rmirror] In VLAN stacking, mirror the access port and the direction is both, the ether
type in connected port should be 8100, not 9100.
285. [RMirror] DUT Ping DUT sometimes fail via RMirror Connected port.
286. [MIB-zyxelSflow] The zyxelSflowPortCollectorTable (OID: 1.3.6.1.4.1.890.1.15.3.75.1.6)
value can't be gotten via MIB Browser.
287. [DHCPv6 Client] In DHCPv6 Client, set information refresh minimum to 9999999999, it
should have warning message when configure over the maximum value.
288. [Private VLAN] When the reserved port for show VLAN counter is link at 10M, the private
VLAN in show counter will be abnormal. (the received rate is around 10M).
289. [MIB-IP]When using SilverCreek to test the ipNetToMediaTable (OID: 1.3.6.1.2.1.4.22), it
will pop "Agent returned out of range index value 0 is out of the range (1..2147483647) for
index IP-MIB:ipNetToMediaIfIndex of object IP-MIB:ipNetToMediaIfIndex.0.192.168.0.38"
error message.
290. [static ARP] create a static ARP with different IP and port with duplicated MAC; static
ARP overwrite dynamic success, but port didn't change to the one which just created
when show mac
Advertisement
Table of Contents
