Table of Contents
Advertisement
100. [MIB-zyxelPrivateVlan] The zyPrivateVlanAssociatedPrimaryVid (OID:
1.3.6.1.4.1.890.1.15.3.68.1.1.1.2) can't be set via SNMPc or MIB Browser.
101. [MIB-zyxelPrivateVlan] When using SilverCreek to test the
zyPrivateVlanAssociatedPrimaryVid (OID: 1.3.6.1.4.1.890.1.15.3.68.1.1.1.2), it will pop
error message - "Agent returned out of range integer value 0 is outside the range of
(1..4096) for ZYXEL-PRIVATE-VLAN-MIB:zyPrivateVlanAssociatedPrimaryVid.4094".
102. [MIB-zyxelProtocolBasedVlan] The zyProtocolBasedVlanMaxNumberOfVlans (OID:
1.3.6.1.4.1.890.1.15.3.69.1.1) value shows error. It should be Port No * 8.
(XGS3700-48HP --＞ 416. GS3700-24HP --＞ 224).
103. [IPv6] When modify link-local address from automatically generate (enable ipv6) to static
configure and ping the same domain ipv6 address, the icmp request will carry
automatically configure link- local address, not static configure link-local address.
104. [IPv6] Use static global ipv6 address to ping the same domain ipv6 adrress, ping will be
ok. But, remove static global ipv6 address, ping still be ok.
105. [IPv6] Use static global ipv6 address with eui-64 to ping the same domain ipv6 adrress,
ping will be ok. But, remove static global ipv6 address with eui-64, ping still be ok.
106. [MAC Authentication] set name prefix then do mac authentication, check authentication
mac should not be "static"
107. [MAC Authentication] Verify mac authentication + port security, after disable port-security,
DUT can't forward any traffic.
108. [MIB-zyxelRadius] When setting the zyRadiusAuthenticationServerIpAddr (OID:
1.3.6.1.4.1.890.1.15.3.71.1.1.3.1.2) to invalid value, it should pop error message.
109. [MIB-zyxelRadius] When setting the zyRadiusAccountingServerIpAddr (OID:
1.3.6.1.4.1.890.1.15.3.71.1.2.2.1.2) to invalid value, it should pop error message.
110. [Guest VLAN] when show port-access-authenticator ＜port＞, Supplicant MAC format
error
111. [IPV6] In default ns-interval, ping non-existent ipv6 address, it should only send 3 NS
packets.
112. [MIB-zyxelRemotePortMirror] The zyRemotePortMirrorMaxNumberOfVlans (OID:
1.3.6.1.4.1.890.1.15.3.73.1.1) shows value = 4094. but DUT only can create 5 rules.
113. [MIB-zyxelRemotePortMirror] When using SilverCreek to create max
zyRemotePortMirrorRowStatus (OID: 1.3.6.1.4.1.890.1.15.3.73.1.2.1.9) rules, it will cause
DUT can't erase RMirror setting via CLI.
114. [MIB-zyxelRip] DUT doesn't support the zyxelRip (OID: 1.3.6.1.4.1.890.1.15.3.74)
function, please remove its setting.
115. [MIB-zyxelSflow] The zySflowMaxNumberOfPortCollectors (OID:
1.3.6.1.4.1.890.1.15.3.75.1.5) should be 28 for GS3700-24HP, not 52.
116. [MIB-zyxelSflow] When using SilverCreek to test the zySflowCollectorUdpPort (OID:
1.3.6.1.4.1.890.1.15.3.75.1.3.1.3), it will pop error message - "Agent returned wrong
syntax for ZYXEL-SFLOW-MIB:zySflowCollectorUdpPort.1.4.10.31.9.21. Expected syntax
of ZYXEL-SFLOW-MIB:zySflowCollectorUdpPort.1.4.10.31.9.21 to be INTEGER, not
Gauge".
117. [MIB-zyxelSflow] Using "Get" way to get the zyxelSflowPortCollectorTable (OID:
1.3.6.1.4.1.890.1.15.3.75.1.6) will fail, but using "Next-Get" way is OK.
118. [MAC authentication] send wire-speed unknow packets to authenticator port then do mac
flush, packet should not flooding to other port.
119. [MIB-zyxelSnmp] The zySnmpVersion (OID: 1.3.6.1.4.1.890.1.15.3.76.1.6) can't be set
via SNMPc or MIB Browser.
120. [MIB-zyxelSnmp] The zySnmpTrapDestinationUdpPort (OID:
1.3.6.1.4.1.890.1.15.3.76.1.5.1.2) can't be set via SNMPc or MIB Browser.
121. [MIB-zyxelSnmp] The zySnmpTrapDestinationVersion (OID:
1.3.6.1.4.1.890.1.15.3.76.1.5.1.3) can't be set to 0 (v1) or 2 (v3) via SNMPc or MIB
Browser.
122. [MIB-zyxelSnmp] The zySnmpTrapDestinationUserName (OID:
1.3.6.1.4.1.890.1.15.3.76.1.5.1.4) can't be set via SNMPc or MIB Browser.
123. [MIB-zyxelSnmp] The zySnmpUserSecurityLevel (OID:
1.3.6.1.4.1.890.1.15.3.76.1.7.1.2), zySnmpUserAuthenticationProtocol (OID:
1.3.6.1.4.1.890.1.15.3.76.1.7.1.3) and zySnmpUserPrivacyProtocol (OID:
1.3.6.1.4.1.890.1.15.3.76.1.7.1.4) access type is "read-write", but they can't be set via
SNMPc or MIB Browser.
Advertisement
Table of Contents
