ZyXEL Communications XGS3700-24HP Release Note/Manual Supplement page 46

153. [Mirror] In mirror test, the learned packet will broadcast to other ports. The behavior is
abnormal. Execute MAC-Flush, DUT will be ok.
154. [Mirror] Non Monitor port can receive the traffic in the mirrored port.
155. [IPv6 ND] Send 8K ND packets into Device then check Neighbor table in web page,
device will hang up or crash.
156. [Web] The ARP table should add "Age" time via Web. Web should be the same CLI.
157. [Web - Diagnostic] The system log should be display 1000 entries via Web. Web should
be the same CLI.
158. [Rmirror] The reflector port set fails when create one entry.
159. [Web - Rmirror] The reflector port set fails and display abnormal when create one entry.
160. [RMirror] The error message is not intuition when set reflector port fails.
161. [CFM] In local stack table, it will have one redundant entry in port 29. The issue seems to
only occurs in 24HP, not 48HP.
162. [Private VLAN] In web page, remove default VLAN 1 and add primary VLAN, isolate
VLAN and community VLAN, CLI could not synchronous with Web page.
163. [MIB-IEEE] When deleting the dot1agCfmMepDbTable (OID: 1.3.111.2.802.1.1.8.1.7.3)
value, the dot1agCfmMepDbChassisIdSubtype (OID: 1.3.111.2.802.1.1.8.1.7.3.1.8) will
show "0" and SilverCreek will show "Agent returned out of range enumeration 0 is not a
known value for IEEE8021-CFM-MIB:dot1agCfmMepDbChassisIdSubtype.1.1.1.2" error
message.
164. [Web] Set DHCP Relay - Remoter DHCP Server 3 fail after set the IP Address via Web.
165. [PoE Trap] Disable per port PoE trap, DUT still sends PSE port on/off trap when PD
connect to DUT.
166. [Service Access Control] When change https service port value via Web, then show
running-configuration didn't display configuration via CLI.
167. [Service Access Control] When change SSH service port value via Web, then show
running-configuration didn't display configuration via CLI.
168. [Service Access Control] The telnet and ftp service port setting didn't clear after erase
running-configuration.
169. [DHCP Snooping] The DHCP snooping profile setting didn't clear after erase
running-configuration.
170. [Flow Control] Flow control could not load balance cross unit
171. [DHCP Server] When release 253 client IP address, it could not release all client IP, and
the timer in DHCP server table will be infinite. (Release rate: 5 packet /s)
172. [DHCP Server] After request 253 and release 253 client IP, it could not get 253 dynamic
IP again.
173. [RMON] etherHistorycontrol utilization was incorrect (using Gb port)
174. [MIB-zyxelIpsg] When testing the zyArpFreezeVlan (OID: 1.3.6.1.4.1.890.1.15.3.33.1.3),
it will show "Add [mac=00:19:cb:f8:6d:ca IP=192.168.1.1 vid=95 port=0 ] to IPSG static
binding table." message but PC Port connect to VLAN 1.
175. [IP] In out- band, user can overwrite IP address with 192.168.0.1/16. But, in in-band, user
can't overwrite IP address with 192.168.1.1/16.
176. [Static ARP] in the web, the last index number for ARP should be 256, not 0
177. [MIB] When setting the port list format to 0x80 to related items, sometimes MIB will return
invalid value.
178. [DHCP Server] In backup/restore configuration file or reboot device, sometimes, it could
not clear client IP entry in DHCP server status after user release client IP. Besides, the
timer in client IP entry will be infinite.
179. [DHCPv6 Relay] DUT can't transfer DHCP Solicit into Relay_Forw through DHCP Relay
Agent.
180. [IPv6]Send ICMPv6 neighbor advertisement packets (SA: 00:19:cb:01:01:01) into device,
and enable ipv6, sometimes, device only display as "preferred", not "duplicated".
181. [Service Access Control] The warning message should be write timeout range about
telnet timeout value via CLI and Web.
182. [Service Access Control] The warning message should be write timeout range about FTP
timeout value via CLI and Web.
183. [Service Access Control] The warning message should be write timeout range about Http
timeout value via CLI and Web.
184. [Service Access Control] The warning message should be write timeout range about
Console timeout value via CLI and Web.