Table of Contents
Advertisement
18. [DHCP] Create DHCP Relay VLAN per port setting, then backup configuration fails and
CLI will hang up.
19. [DHCP] Create DHCP Relay VLAN per port setting, then CLI pop error message when
show running-configuring.
20. [MIB-zyxelIpsg] When using SilverCreek to test the zyArpFreeze (OID:
1.3.6.1.4.1.890.1.15.3.33.1.1), DUT will crash.
21. [Broadcast Storm Control] The rate minimum value is 2, not 0.
22. [IGMP-snooping] When reload configuration, CLI pop error message.
23. [Port Move] After port move, the MAC type in MAC table should be dynamic, not static.
24. [ACL] The classifier rule only create 192, and policy rule only 128.
25. [DHCP] In DHCP snooping, DHCP relay (smart relay, VLAN based relay), profile could not
compatible with previous option, information.
26. [Flow Control] In either 10M/full or 10M/half mode, when traffic is congestion, the received
rate from incoming traffic could not balance
27. DHCP Snooping] "Option 82" should be option82 with no space (match the word option82
in DHCP Relay)
28. [MSTP] In RSTP, MRSTP, MSTP, port 1 information should display as "port 01 info",
not "port 1 info". It should keep the consistence with the previous product.
29. [Out-Of-Band] Use Out-Of-Band port to access device via web page, CLI will pop error
messages.
30. [VLAN-stacking] When port-security + QinQ access port didn't workable.
31. [Interface] When port 1 set speed-duplex 100-full, the link status display 100M/H.
32. [Intrusion-Lock] The GS3700-24HP/XGS3700-48HP should support intrusion-lock.
33. [Clone] The clone lack port "related trap" for CLI and Web.
34. [sflow] The string is wrong. It should "sflow", not "sFlow".
35. [TRTCM] When reload configuration, CLI pop error message.
36. [Loopguard] The loopguard re-active issue.
37. [IPSG] The rate is abnormal when enable IPSG.
38. [Service Access Control] Enable SSH function with specific port, SSH should be display in
the show run
39. [Mirror] When mirrored port and monitor port are in different unit, sometimes, monitor port
could not receive any traffic from mirrored port.
40. [Access Control] erase running configuring, device should reset all to default
41. [Port Security] In show port security with specified port index, the entry has wrong index.
42. [MVR] When MVR delete all check box via web, web return error message.
43. [MIB-zyxelDhcpRelay]When setting the invalid value to
zyDhcpRelayGlobalRelayOption82Profile (OID: 1.3.6.1.4.1.890.1.15.3.18.1.1.4), it should
pop error message. (The zyDhcpRelayGlobalRelayState is disabled)
44. [MIB-zyxelDhcpRelay]The zyDhcpRelayGlobalRelayOption82PortProfile (OID:
1.3.6.1.4.1.890.1.15.3.18.1.1.6.1.1) can't set to Port28.
45. [MIB-zyxelDhcpRelay]The zyDhcpRelayVlanRelayOption82VlanPortProfile (OID:
1.3.6.1.4.1.890.1.15.3.18.1.2.6.1.1) can't set to Port28.
46. [MIB-zyxelDhcpSnooping]The zyDhcpSnoopingOption82VlanPortProfile (OID:
1.3.6.1.4.1.890.1.15.3.20.1.7.1.1) can't set to Port28.
47. [MIB-zyxelDhcpv6]Setting the zyDhcpv6RelayOptionIfIdState (OID:
1.3.6.1.4.1.890.1.15.3.21.1.2.1.4) from enabled (1) to disabled (2) will fail.
48. [MIB-zyxelDhcpv6] When setting the zyDhcpv6RelayOptionRemoteIdData (OID:
1.3.6.1.4.1.890.1.15.3.21.1.2.1.5) to 65 characters, it should pop error message.
49. [PoE] In consumption mode, when all PDs connect to the device, consumption power will
exceed total power. The behavior is abnormal.
50. [MIB-zyxelDhcpv6] The zyDhcpv6ClientIaTypeState (OID:
1.3.6.1.4.1.890.1.15.3.21.1.3.1.2) and zyDhcpv6ClientIaTypeRapidCommitState (OID:
1.3.6.1.4.1.890.1.15.3.21.1.3.1.3) default value should be 2 (disabled), not "0".
51. [IGMP-snooping] The IGMP-snooping fast leave didn't send specific query when receive
leave packets.
52. [MIB-zyxelDhcpv6]The zyDhcpv6ClientInfoRefreshMinimum (OID:
1.3.6.1.4.1.890.1.15.3.21.1.3.1.6) can't set to max value - 4294967295 via SNMPc or MIB
Browser.
53. [IGMP-snooping] The IGMP-snooping fast leave didn't send specific query when receive
leave packets in MVR topology.
Advertisement
Table of Contents
