Table of Contents
Advertisement
240. [SNMP-zyxelArp] Using "Get" way to get zyStaticArpRowStatus (OID:
1.3.6.1.4.1.890.1.15.3.11.1.4.1.5) will fail, but using "Next-Get" is OK.
241. [MIB-zyxelArp] When using SilverCreek to test the zyArpPort (OID:
1.3.6.1.4.1.890.1.15.3.11.2.1.1.4), it will show "Agent returned out of range enumeration 1
is not a known value for ZYXEL-ARP-MIB:zyArpPort.192.168.1.10.1" error message.
242. [Port interface] Linked port was sync slow (about 5 seconds) when unplug/plug into the
DUT (link up and down twice before linked success)
243. [LLDP-med] when show either LLDP info local/remote port, the Extended TLV Info
should display as LLDP-MED OUI not 802.1 OUI
244. [DHCP Relay] In smart relay mode, when management VLAN and client VLAN are
different, some model carry client VLAN IP as source IP (3700 Series) , some model (2200
Series) carry management VLAN IP as source IP. Which one is correct
245. [Arp Inspection] The log-buffer entries display abnormal in ARP inspection log-buffer
function.
246. [SNMP-zyxelIpv6] Setting the invalid value to zyIpv6DefaultGateway (OID:
1.3.6.1.4.1.890.1.15.3.34.1.5.1.7) will make the original value become empty.
247. [SNMP-zyxelIpv6] The rule -
zyIpv6GlobalAddressRowStatus.31023.2.16.16.35.0.0.0.0.0.0.0.0.0.0.0.0.0.1.64.0 (OID:
1.3.6.1.4.1.890.1.15.3.34.1.6.1.7) can't be created via MIB, but CLI is OK.
248. [MIB-zyxelIpv6Ndp] The
zyNdpPrefixRowStatus.31023.2.16.1023.1.0.0.0.0.0.0.0.0.0.0.0.0.0.1.64 and
zyNdpPrefixRowStatus.32047.2.16.2047.1.0.0.0.0.0.0.0.0.0.0.0.0.0.1.64 can't be created
via MIB Browser.
249. [IPv6 Neighbor Setup] Create maximum ipv6 neighbor setup, it could not delete the last
entry via web page. It will pop error message. Interface id range error. CLI can delete the
last entry directly.
250. [syslog] ping test to correct IP, it should display IN ping: ping test to the IP "completed"
(not "failed") when show logging
251. [port move] connect two devices with port1 and port2, ping passed; after port moved
(connected to port 3), ping failed. Check on the mac table, connected port (same mac)
was still display the previous port which was port1. It should be immediately change to the
current connecting port (port3) after port moves.
252. [SNMP-zyxelMvr] The zyMvrGroupStartIpAddress (OID:
1.3.6.1.4.1.890.1.15.3.55.1.5.1.3) and zyMvrGroupEndIpAddress (OID:
1.3.6.1.4.1.890.1.15.3.55.1.5.1.5) can't be set via SNMPc, but SilverCreek is OK.
253. [MIB-zyxelSflow] The over max zySflowPortCollectorRowStatus (OID:
1.3.6.1.4.1.890.1.15.3.75.1.6.1.5) rules can be created.
254. [MIB-zyxelSnmp] The zySnmpTrapSysGroup (OID: 1.3.6.1.4.1.890.1.15.3.76.1.8.1.1)
lacks "dyinggasp" selected item.
255. [MIB-zyxelSnmp] The zySnmpTrapAAAGroup (OID: 1.3.6.1.4.1.890.1.15.3.76.1.8.1.3)
lacks "authorization" selected item.
256. [MIB-zyxelTacacs] When setting the zyTacacsAuthenticationServerIpAddress (OID =
1.3.6.1.4.1.890.1.15.3.83.1.1.3.1.2) and zyTacacsAccountingServerIpAddress (OID =
1.3.6.1.4.1.890.1.15.3.83.1.2.2.1.2) to invalid value, it should pop error message.
257. [MIB-zyxelIpv6StaticRoute]It should be denied to set the
zyIpv6StaticRouteNextHopIpAddress (OID: 1.3.6.1.4.1.890.1.15.3.37.1.2.1.5) to unexist
IP domain.
258. [Policy Route] When create policy route rule without profile name, the behavior is
abnormal.
259. [RMirror] After set mirror port's direction on source switch via web, then use CLI to show
running-config will abnormal.
260. [RMirror] Set mirror port direction fail via CLI.
261. [IPv6] Create maximum ipv6 neighbor setup (256) per VLAN, then enable ipv6 (256) per
VLAN, CLI will pop error messages continuously.
262. [IPv6 Status] Restore the attachment file, the ipv6 status in last 1,2 is abnormal in web
page.
263. [IPv6 Interface Setup] It can create 128 ipv6 interface VLAN. But, it only enable 64 ipv6 in
interface VLAN. it will cause the remainder 64 ipv6 interface VLAN could not work.
264. [Rmirror] In web page, the default direction value in source switch should be "both",
not "ingress".
Advertisement
Table of Contents
