Vector Welding C-Series Operating Instructions Manual page 4

3.1 Troubleshooting----------------------------------------------------------------------- 64-65
Chapter 4: DC Pulse Series Equipment
T-Series
------------------------------------------------------------------------------- 66-66
1.Summary
1.1 Brief introduction----------------------------------------------------------------------- 67-68
1.2 Working principle-----------------------------------------------------------------------68-68
1.3 Volt-ampere characteristic---------------------------------------------------------- 69-69
1.4 Specifications T231/T331------------------------------------------------------------ 69-70
1.5 Duty cycle ----------------------------------------------------------------------------- 70-70
1.6 Packaged items------------------------------------------------------------------------ 71-71
2.Operation
2.1 Layout for the panel T231/T331------------------------------------------------------ 71-75
2.2 Control panel---------------------------------------------------------------------------- 75-76
2.3 Setup for STICK(MMA) welding ------------------------------------------------------ 77-77
2.4 Setup for LIF TIG welding------------------------------------------------------------ 78-78
2.5 Operation environment---------------------------------------------------------------- 79-79
2.6 Operation notices--------------------------------------------------------------------- 79-79
3.Troubleshooting
3.1 Troubleshooting---------------------------------------------------------------------- 80-82
Chapter 5: Multifunction Series Equipment
O-Series
----------------------------------------------------------------------------- 83-83
1.Summary
1.1 Brief introduction----------------------------------------------------------------------- 84-84
1.2 Working principle---------------------------------------------------------------------- 85-85
1.3 Volt-ampere characteristic---------------------------------------------------------- 85-85
1.4 Specifications O241/O251---------------------------------------------------------- 86-86
1.5 Duty cycle-------------------------------------------------------------------------------87-87
1.6 Packaged items----------------------------------------------------------------------- 88-88
2.Operation
2.1 Layout for the panel O241----------------------------------------------------------- 88-92
2.2 Control panel---------------------------------------------------------------------------- 92-93
2.3 Layout for the panel O251------------------------------------------------------------ 94-98
2.4 Control panel ------------------------------------------------------------------------ 98-101
2.5 Setup for STICK (MMA) welding O241----------------------------------------- 101-102
2.6 Set-up for LIFT TIG (GTAW) welding O241----------------------------------- 102-103
2.7 Setup for cutting (CUT) O241--------------------------------------------------- 103-105
2.8 Setup for STICK (MMA) welding O251----------------------------------------- 105-106
2.9 Set-up for LIFT TIG (GTAW) welding O251----------------------------------- 106-107
2.10 Setup for cutting (CUT) O251-------------------------------------------------- 107-109
2.11 Operation environment--------------------------------------------------------- 109-109
2.12 Operation notices------------------------------------------------------------- 110-110
3.Troubleshooting
3.1 Troubleshooting------------------------------------------------------------------- 110-112
Chapter 6: MIG Series Equipment
R-Series
--------------------------------------------------------------------------- 113-113
1.Summary
1.1 Brief introduction------------------------------------------------------------------ 114-114
1.2 Working principle------------------------------------------------------------------ 114-114
1.3 Specifications R221-------------------------------------------------------------- 115-115
1.4 Packaged items----------------------------------------------------------------- 116-116
1.5 Duty cycle------------------------------------------------------------------------- 116-116
1.6 Specifications R231-------------------------------------------------------------- 117-117
1.7 Packaged items ------------------------------------------------------------------- 118-118
1.8 Duty cycle--------------------------------------------------------------------------- 118-118
1.9 Specifications R251/R311------------------------------------------------------ 119-119
1.10 Packaged items------------------------------------------------------------------ 120-120
1.11 Duty cycle-------------------------------------------------------------------------- 120-120
2.Operation
2.1 Layout for the panel R221------------------------------------------------------ 121-122
2.2 Layout for the panel R231------------------------------------------------------ 123-125
2.3 MIG gun polarity lead------------------------------------------------------------- 125-125
2.4 Layout for the panel R311--------------------------------------------------------- 126-127
2.5 Installing a 5 kg spool 200mm diameter (for R221,R231)------------------- 127-128
2.6 Installing a 15 kg spool 300mm diameter (suitable for R251 and R311------128-128
2.7 Inserting wire into the feed mechanism---------------------------------------- 128-129
2.8 Feed roller pressure adjustment--------- ---------------------------------------- 130-130
2.9 Changing the feed roll------------------------------------------------------------- 130-131
2.10 Shielding gas regulator operating instructions----------------------------- 131-134
2.11 Set-up MIG (GMAW) welding with gas shielded MIG wire----------------- 134-135